Programmable group-delay module using binary polarization switching

We demonstrate the first programmable group-delay module based on polarization switching. With a unique binary tuning mechanism, the device can generate any differential group delay value from -45 to +45 ps with a resolution of 1.40 ps, or any true-time-delay value from 0 to 45 ps with a resolution of 0.7 ps. The delay varying speeds for both applications are under 1 ms and can be as fast as 0.1 ms. We evaluate both the dynamic and static performances of the device while paying special attention to its dynamic figures of merit for polarization-mode dispersion emulation and compensation applications. Our experiment shows that the device exhibits a negligible transient-effect induced power penalty (<0.2 dB) in a 10-Gb/s nonreturn-to-zero system.     

Ф16mm、Ф18mm钼棒的研制

采用等静压制法，压制钼圆棒坯，经中频高温烧结，制得尺寸适合、用户满意的钼电极棒。     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

化学束外延

本文介绍了化学束外延(CBE)的发明和发展,论述了CBE的原理和设备。文中还介绍了最近提出的一种生长机理。     

A three-dimensional non-epitaxial atomistic growth model for thin-film deposition: effect of surface mobility

The effect of the atomic mobility on a film surface has been studied by using a three-dimensional atomistic thin-film deposition model which simulates three-dimensional thin-film images, surface profiles and cross-sectional area pictures. In addition, quantitative results of surface RMS roughness, average film thickness, atomic coordination number and its distribution, and solid fraction of the deposited thin films, were obtained from the simulations. When the film surface mobility increased from 0.3 to 3.0, RMS roughness decreased from 6.5 to 1.1, solid fraction increased from 0.27 to 0.56 and average film thickness decreased from 40 to 28, due to the reduction of the voids within the film. The full-width half magnitude of the atomic coordination distribution became narrower indicating the increased degree of crystallization. With increase in surface mobility crossing the boundary to 1.5, the film evolved from a porous or loose columnar structure with voids, to a densely packed fibrous grain structure which can be categorized by the zone structure models.     

A high-current and high-temperature 6H-SiC thyristor

A 6H-SiC thyristor has been fabricated and characterized. A forward breakover voltage close to 100 V and a pulse switched current density of 5200 A/cm² have been demonstrated. The thyristor is shown to operate under pulse gate triggering for turn-on and turn-off, with a rise time of 43 ns and a fall time of less than 100 ns. The forward breakover voltage is found to decrease by only 4% when the operating temperature is increased from room temperature to 300°C. It is found that anode ohmic contact resistance dominates the device forward drop at high current densities     

特征X射线能谱法测定Fe^＋注入小麦种子的深度

用１１０ｋｅＶ Ｆｅ＾＋离子束垂直注入小麦种胚后，在扫描电子显微镜上沿种子纵沟剖面，在不同深度上测量Ｆｅ元素被激发出的特征Ｘ射线强度分布，结果表明分布呈指数衰减，与晶体中的热扩散分布相类似，并对此进行了讨论。     

Performance characteristics of parallel resonant convertor

Using a set of characteristic curves derived from the stateplane analysis, a novel approach to the design of the parallel resonant convertor (PRC) is presented. It will be shown that the steady-state response of the convertor can also be obtained from these characteristic curves     

HHD型核子秤电离室物理性能检测

HHD型核子秤电离室已成功地使用于HCS型核子秤.对它的各种物理性能指标进行了检测,各项性能指标都达到了设计要求。