Location of structural sections from within a highly distorted complex line drawing

Complex and highly distorted line drawings are produced by subjects attempting the Rey Complex Figure test, a clinical test of neuropsychological assessment. However, the marking scheme conventionally employed can be subjective and unreliable. In this paper, the first stages in automating this scoring system are investigated using a robust technique to locate a reduced set of scoring sections and a knowledge-based system that employs spatial metrics and fuzzy approximation techniques. Testing the technique using clinical data produced encouraging results that support the argument that this is a feasible approach for implementing a fully automated system, and that in its current state, can be immediately applied in a semi-automated system.     

Crystallization study of chemically vapour-deposited amorphous silicon films by in situ x-ray diffraction

The solid phase crystallization kinetics of chemically vapour-deposited amorphous silicon films were studied by in situ X-ray diffraction. We determined the crystalline volume directly from the Bragg peak intensities at various times during isothermal annealing in the temperature range 578 °C < T < 658 °C. From these experiments we deduced that the crystallization was due to nucleation predominantly at the substrate-film interface followed by crystal growth perpendicular to this interface. The crystal growth rate was thermally activated with an activation energy E_v of 3.1 eV. A strong 〈111〉 preferred orientation of the growing polycrystal was observed and the grain size remained constant at about 60 nm. Evidence of stresses at the amorphous-crystalline interface during the early stages of crystallization was observed. A comparison with previous conductivity measurements is also carried out.     

Compact implementation of high-performance CMOS current mirror

A high-performance compact current mirror implementation with very low input resistance, very high output resistance, high copying accuracy, low input and output voltage supply requirements and high bandwidth is proposed. The circuit characteristics are validated with simulations in 0.5 /spl mu/m CMOS technology and with experimental results.     

Crystal growth of selected II–VI semiconducting alloys by directional solidification: Part I Ground-based experiments

A series of Hg_0.84Zn_0.16 Te crystal ingots have been grown from pseudobinary melts by the Bridgmam–Stockbarger type directional solidification using a Marshall Space Flight Center/Space Science Laboratory heat-pipe furnace and the ground control experiment laboratory furnace of the crystal growth furnace which was flown on the first United States Microgravity Mission. A number of translation rates and a series of hot- and cold-zone temperatures were employed to assess the influence of growth parameters on the crystal properties for the purpose of optimizing the in-flight growth conditions. This revised version was published online in November 2006 with corrections to the Cover Date.     

Effect of starting particle size on hot-pressing of magnesium oxide powder prepared by vapour-phase oxidation process

Effect of starting particle size on hot-pressing of magnesium oxide (MgO) powder was examined using seven kinds of MgO powders prepared by a vapour-phase oxidation process; the average primary particle sizes were 11, 25, 32, 44, 57, 107 and 261 nm. These compressed powders (compacts) were hot-pressed at a temperature between 900 and 1300°C. The densifications of these compacts during the hot-pressing proceeded via (i) the sintering of primary particles within secondary particles and the rearrangement of secondary particles/grains (900°C), (ii) the gradual grain growth controlled by the pore migration (900∼1100°C) and (iii) the rapid grain growth due to the active mass transfer (1300°C); the grain sizes of MgO compacts hot-pressed at and below 1100°C were <1 μm, while those at 1300°C attained 20∼30 μm. The transluscent compact with the relative density of 99.7% could be obtained when the compressed powder with the average primary particle size of 44 nm was hot-pressed at a temperature as low as 1100°C for 1 h. This revised version was published online in November 2006 with corrections to the Cover Date.     

Unfavorable mechanical effects of heat and moisture exchangers in ventilated patients

OBJECTIVE: To investigate the mechanical effects of artificial noses. SETTING: A general intensive care unit of a university hospital. PATIENTS: 10 patients in pressure support ventilation for acute respiratory failure. INTERVENTIONS: The following three conditions were randomly tested on each patient: the use of a heated humidifier (control condition), the use of a heat and moisture exchanger without filtering function (HME), and the use of a combined heat and moisture exchanger and mechanical filter (HMEF). The pressure support level was automatically adapted by means of a closed-loop control in order to obtain constancy, throughout the study, of patient inspiratory effort as evaluated from airway occlusion pressure at 0.1 s (P0.1). Patient's ventilatory pattern, P0.1, work of breathing, and blood gases were recorded. MEASUREMENTS AND MAIN RESULTS: The artificial noses increased different components of the inspiratory load: inspiratory resistance, ventilation requirements (due to increased dead space ventilation), and dynamic intrinsic positive end-expiratory pressure (PEEP). The additional load imposed by the artificial noses was entirely undertaken by the ventilator, being the closed-loop control of P0.1 effective to maintain constancy of patient inspiratory work by means of adequate increases in pressure support level. CONCLUSIONS: The artificial noses cause unfavorable mechanical effects by increasing inspiratory resistance, ventilation requirements, and dynamic intrinsic PEEP. Clinicians should consider these effects when setting mechanical ventilation and when assessing patients' ability to breathe spontaneously.     

Preparation of autologous bone marrow grafts for cryopreservation using the AS104 cell separator

The heterocomplex of glycoproteins E and NS1 of tick-borne encephalitis (TBE) virus was isolated from culture fluid of continuous SPEV (porcine embryo kidney) cells by affinity chromatography on CL4B sepharose with immobilized monoclonal antibodies to TBE virus protein NS1. Comparison of the TBE E-NS1 heterocomplex from culture fluid and cells showed the predominance of secreted extracellular form. A similar TBE virus heterocomplex E-NS1 was revealed in the blood sera of patients with TBE but not in their lymphocytes. Extracellular localization of the E-NS1 complex at the late stage of infection rules out its hypothesized participation in the replication of TBE virus. Virtual absence of the heterocomplex and presence of proteins E and NS1 in high concentrations in the cells makes the nonspecific aggregation of these proteins impossible. Evidently, the extracellular heterocomplex E-NS1 may react with virusspecific antibodies or with cytotoxic T lymphocytes.