Analysis and Modelling of the LPC VD Annular Reactor

This paper presents the results of our work on a new type of CVD reactor, annular reactor. This equipment is able to deposit pure silicon and also in-situ phosphorus doped silicon on a large number of substrates     

AC measurements of the minimum longitudinal resistance of a QHEsample from 10 Hz to 10 kHz

AC measurements of the longitudinal resistance, R_xx, of a quantum Hall effect (QHE) sample have been made in a frequency range from 10 Hz to 10 kHz. The results show no frequency effect on the minimum value of R_xx corresponding to the quantum numbers i=2 and i=4, within the measurement resolution of 0.5 mΩ. Therefore, the influence of frequency on the value of the quantized Hall resistance, R_H, should not exceed a few parts in 10⁹ . Some unwanted effects detected during the development of the resistance bridge have been pointed out     

Motion of a solid sphere in a general flow near a plane boundary at zero Reynolds number

It is demonstrated how the hydrodynamic force and moment of force acting on a solid sphere may be calculated when it is placed at rest at an arbitrary position in a two dimensional flow at zero Reynolds number in which the region of flow is bounded by either an undeformable planar free surface or by a plane solid wall. The results so obtained are used to calculate the motion of a freely moving solid sphere in an asymmetric vortex in the presence of an underformable free surface. It is seen that the sphere, depending on the direction of the undisturbed flow, will either spiral into or out of the vortex. This implies that when a dilute suspension of such spherical particles undergoes such a vortex motion in the presence of the free surface, the vortex will either fill up with particles from the surrounding flow or become devoid of particles.Deceased, July 31, 1995     

Process optimization and related material properties of silicon films produced by laser-induced chemical vapour deposition from silane

Laser-induced chemical vapour deposition of silicon films on SiO₂/Si (1 0 0) and Si (1 0 0) substrates was studied using ArF laser irradiation of silane/argon gas mixture in parallel to the substrate. The optimal deposition conditions were specified by examination of film morphology at a wide range of irradiation and process parameters. At optimal conditions, specular films were obtained with no powder formation. The effect of deposition parameters, such as laser energy and repetition rate, on the deposition rate and the related film quality, was investigated.     

Melt-extracted oxide ceramic fibres — the fundamentals

A melt-extraction technique, using a sharpened molybdenum wheel, has been used to produce fine oxide ceramic fibres. Wetting of the molybdenum wheel by molten ceramic is a key parameter in the melt-extraction process. Two types of fibre are generally obtained, depending on the extraction speed. At very low wheel speed, fine and uniform fibres of high quality are produced. However, when the wheel speed exceeds a critical velocity, Rayleigh waves are formed on the free surface of the fibres. Moreover, the average fibre thickness first increases with the wheel velocity, then passes through a maximum, decreasing at high velocity. This thickness variation is discussed in terms of both surface tension and viscosity of the liquid ceramics.     

Cumulant calculations of thermodynamic quantities for the Hubbard and the emery model

The calculations of the first paper suggesting phase separation in the Hubbard model [2] are performed under modern computer facilties for the one and three-band Hubbard model. High-temperature approximations for specific heat and static correlation functions are obtained. The latter show, at these high temperatures, no tendency to phase separate in the same way as in the cited paper because our spin parallel nearest-neighbor charge correlation function is negative for all doping values. The spin antiparallel correlation function has positive and negative values for different doping regimes.Extension of this work to higher levels of iterations and to other correlation functions is in progress.     

Experimental and numerical investigation of fracture in double-edge notched steel plates

Double-edge notched (DENT) steel plates were pulled until complete fracture and several experimental observations were made (using profilometry and scanning electron microscopy). The essential work of fracture (EWF) model was found to be well verified. Numerical simulations—up to the maximum load only—of some experiments were performed using the finite element method (FEM), and incorporating geometric and material non-linearities (large deformation elasto-plasticity). Some experimental measurements were compared with the corresponding numerical computations and excellent agreement was found.     

Propagation of a quasi-shear horizontal acoustic wave in Z-Xlithium niobate plates [and conductivity sensor application]

It is found that an acoustic wave which is nearly polarized in the shear horizontal (SH) direction can propagate along the X axis of a Z-cut lithium niobate plate if the ratio h/λ, where h=plate thickness and λ=acoustic wavelength, is less than about 0.5. Attractive properties of this quasi-SH wave include: (1) phase velocity nearly constant for all values of h/λ; (2) ability to propagate in contact with a liquid medium; and (3) electromechanical coupling coefficient as high as 0.15. These properties make the wave attractive for use in a variety of sensor and signal processing applications. An example of sensor applications is illustrated by using the wave to measure conductivity of liquids (aqueous KCl solution). The frequency of a 12-MHz quasi-SH mode oscillator fabricated on a 0.48 wavelength thick Z-X lithium niobate plate is found to vary by more than 80 kHz for variation in KCI concentration from 0 to 0.15%