Electrode impedance parameters and internal resistance of a sealed LiC/Li1-xCoO2 lithium-ion rechargeable battery

The individual electrode impedance parameters and internal resistance of a sealed LiC/Li1-xCoO2 lithium-ion rechargeable battery were estimated by a galvanostatic nondestructive technique. Various resistive components of the battery were found to be minimum between state-of-charge values 0.5–0.9. It is expected that the operation of the battery within about 50% of its depth-of-discharge would prolong the charge/discharge cycle life of the battery.     

Ultraviolet sensing properties of polyvinyl alcohol-coated aluminium-doped zinc oxide nanorods

Undoped and aluminium (Al)-doped zinc oxide (ZnO) nanorods have been synthesized by electrochemical route. The synthesized materials have been characterized by X-ray diffraction, UV–visible spectrometer and scanning electron microscope. The Al-doped ZnO nanorods have been coated with polyvinyl alcohol. Current–voltage characteristics have been investigated in dark and under UV-light illumination. Aluminium doping in ZnO increase its electrical conductivity and further polyvinyl alcohol coating on Al-doped ZnO increase UV sensitivity of the material. Response and recovery time of Al-doped ZnO and PVA-coated Al-doped ZnO nanorods have been recorded. PVA-coated Al-doped ZnO nanorods shows very fast response and recovery time of 10 s in comparison to uncoated ZnO (20 min) nanorods.     

Fractional M-band dual tree complex wavelet transform for digital watermarking

In this paper, a novel digital watermarking scheme using fractional M-band dual tree complex wavelet transform (Fr-M-band-DT-CWT) is proposed. High frequency channels have wide bandwidth and low frequency channels have narrow bandwidth. These characteristics are suitable for analysing low frequency signal, but not for relatively high frequency signal. The images often contain many edges, which may cause rich middle and high frequency components in the 2-band wavelet domain. Therefore, the ordinary 2-band dual tree complex wavelet transform (DT-CWT) is not well-suited for analysing the image. So, the M-band DT-CWT with the FrFT called Fr-M-band-DT-CWT is proposed in this paper to address this problem. Further, we integrate the Fr-M-Band-DT-CWT with singular value decomposition (SVD) in order to enhance the performance. Experimental results of the proposed watermarking scheme are compared with the previously available watermarking algorithms, fractional Fourier transform (FrFT), fractional wavelet transform (FrWT). Further, the proposed watermark extraction scheme is also tested on different attacks. The results of the present investigations show that the proposed watermarking scheme is superior as compared to other existing watermarking schemes.     

Statistically tuned Gaussian background subtraction technique for UAV videos

Background subtraction is one of the efficient techniques to segment the targets from non-informative background of a video. The traditional background subtraction technique suits for videos with static background whereas the video obtained from unmanned aerial vehicle has dynamic background. Here, we propose an algorithm with tuning factor and Gaussian update for surveillance videos that suits effectively for aerial videos. The tuning factor is optimized by extracting the statistical features of the input frames. With the optimized tuning factor and Gaussian update an adaptive Gaussian-based background subtraction technique is proposed. The algorithm involves modelling, update and subtraction phases. This running Gaussian average based background subtraction technique uses updation at both model generation phase and subtraction phase. The resultant video extracts the moving objects from the dynamic background. Sample videos of various properties such as cluttered background, small objects, moving background and multiple objects are considered for evaluation. The technique is statistically compared with frame differencing technique, temporal median method and mixture of Gaussian model and performance evaluation is done to check the effectiveness of the proposed technique after optimization for both static and dynamic videos.     

Buckling analysis of rectangular composite plates with rectangular cutout subjected to linearly varying in-plane loading using fem

A numerical study is carried out using finite element method, to examine the effects of square and rectangular cutout on the buckling behavior of a sixteen ply quasi-isotropic graphite/epoxy symmetrically laminated rectangular composite plate [0°/+45°/-45°/90°]_2s, subjected to various linearly varying in-plane compressive loads. Further, this paper addresses the effects of size of square/rectangular cutout, orientation of square/rectangular cutout, plate aspect ratio(a/b), plate length/thickness ratio(a/t), boundary conditions on the buckling bahaviour of symmetrically laminated rectangular composite plates subjected to various linearly varying in-plane compressive loading. It is observed that the various linearly varying in-plane loads and boundary conditions have a substantial influence on buckling strength of rectangular composite plate with square/rectangular cutout.     

Optimization of processing parameters in induction hardening using response surface methodology

In this paper, an effective procedure of response surface methodology (RSM) has been utilized for finding the optimal values of process parameters while induction hardening of AISI 1040 under two different conditions of the material i.e., rolled and normalized. Various process parameters, such as feed rate (speed at which the induction coil moves, which is measured in mm/sec), current, dwell time (time after which heat intensity starts to heat work piece in seconds) and gap between the work piece and induction coil have been explored by experiments. Hardness at two different conditions has been considered as performance characteristic. The experiment plan was based on rotatable, central composite design (CCD). The experimental results showed that the proposed mathematical models suggested could describe the performance indicators within the limits of the factors being investigated. The obtained optimal process parameters have been predicted and verified by confirmation experiments. Microstructure and SEM (scanning electron microscope) analyses were also done for justification of the work.     

Properties of Ternary One Dimensional Plasma Photomic Crystals for an Obliquely Incident Electromagnetic Wave Considering the Effect of Collisions in Plasma Layers

An analytical study is presented on the modal dispersion characteristics, group velocity, and effective group, as well as the phase index of a ternary one dimensional plasma photonic crystal for an obliquely incident electromagnetic wave considering the effect of collisions in plasma layers. The dispersion relation is derived by using the transfer matrix method and the boundary conditions based on electromagnetic theory. The dispersion curves are plotted for both the normal photonic band gap structure and the absorption photonic band gap structure. It is found that the increase in the angle of incidence shifts the photonic band gap toward higher frequencies. Also, the cutoff frequency is independent of collisions.     

Nutrient Losses Due to Scarification of Pigeonpea (Cajanus cajan L.) Cotyledons

Outer layers of cotyledons of pigeonpea cultivar C 11 were successively scarified using a Tangential Abrasive Dehulling Device (TADD). Scarification for 0; 2, 4, 8, and 12 min resulted in the removal of 0, 6.7, 12.7, 25.3, and 36.9%, respectively, of powder fractions. The cotyledons and powder fractions at each level of scarification were analyzed for chemical composition, including minerals and trace elements, protein fractions, amino acid composition, and trypsin inhibitor acitivity (TIA). Protein, soluble sugars and ash of the dhal fraction (scarified cotyledons) decreased with increasing scarification time, while starch content increased. Considerable amounts of calcium (about 20%) and iron (about 30%) were removed by scarification for 4 min, but the process did not adversely affect protein quality in terms of amino acids. Trypsin inhibitors were not removed substantially by scarification.     

Process Parameter Effects on Particle Residence Time in a Vertical Scraped Surface Heat Exchanger

Residence times of 1.0-2.0 cm potato cubes with 0.4-1.2% aqueous solutions of sodium carboxymethyl cellulose flowing at 453-599 mli sec were investigated in a vertical scraped surface heat exchanger rotating at 60 160 rpm. Minimum and maximum normalized particle residence times (NPRTs) standard deviation of mean NPRTs, and characteristic parameter for tanks-in-series models were not significantly affected by particle concentration. Mean NPRT for 40% particle concentration was significantly higher than those of single particle - 20% particle concentrations. Mean NPRTs were significantly influenced by process parameters and 2-way interactions.