Oxygen permeation of various archetypes of oxygen membranes based on BSCF

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3‐δ tubes, capillaries, capillary modules, and asymmetric membranes were prepared and tested for oxygen permeation in a dead‐end vacuum operation mode at temperatures up to 850^°C. The capillary module was built up by reactive air brazing using seven capillaries and a supply tube. Two machined discs were used as an end cap and as a connector plate. The oxygen permeation behaves according to Wagner at small driving forces, but significant negative deviations were observed for asymmetric membranes and single capillaries at higher ones. This is caused by pressure drops at the vacuum side for single capillaries. The highest oxygen flux was revealed for the capillary module with 175.5 mL(STP)/min at a low‐vacuum pressure of 0.042 bar at 850^°C, but the asymmetric membrane showing a little bit higher flux at moderate vacuum pressures above 0.07 bar. © 2012 American Institute of Chemical Engineers AIChE J, 58: 3195–3202, 2012     

Phase separation of a hafnium alkoxide-modified polysilazane upon polymer-to-ceramic transformation—A case study

The polymer-to-ceramic transformation of a hafnium alkoxide-modified polysilazane was investigated via thermogravimetric analysis coupled with in situ mass spectrometry (TG/MS), nuclear magnetic resonance (MAS NMR) and transmission electron microscopy (TEM). The results indicate that the structural evolution of the polysilazane upon ceramization is strongly affected by the modification with hafnium alkoxide. Thus, the content of carbon in the ceramic backbone was relatively low, whereas a large amount of SiN₄ sites and a segregated carbon phase was present in the sample. Furthermore, this study revealed the formation of a SiHfCNO amorphous single phase ceramic via pyrolysis of the polymer at 700 °C, whereas at higher pyrolysis temperatures precipitation of hafnia was observed, leading to an amorphous hafnia/silicon carbonitride ceramic nanocomposite. The precipitation of hafnia was shown to not rely on decomposition processes, but to be a result of rearrangement reactions occurring within the ceramic material.     

Proton-Detected Solid-State NMR of the Cell-Free Synthesized α-Helical Transmembrane Protein NS4B from Hepatitis C Virus

Proton-detected 100 kHz magic-angle-spinning (MAS) solid-state NMR is an emerging analysis method for proteins with only hundreds of microgram quantities, and thus allows structural investigation of eukaryotic membrane proteins. This is the case for the cell-free synthesized hepatitis C virus (HCV) nonstructural membrane protein 4B (NS4B). We demonstrate NS4B sample optimization using fast reconstitution schemes that enable lipid-environment screening directly by NMR. 2D spectra and relaxation properties guide the choice of the best sample preparation to record 2D ¹H-detected ¹H,¹⁵N and 3D ¹H,¹³C,¹⁵N correlation experiments with linewidths and sensitivity suitable to initiate sequential assignments. Amino-acid-selectively labeled NS4B can be readily obtained using cell-free synthesis, opening the door to combinatorial labeling approaches which should enable structural studies.     

Is the particle deposition in a cell exposure facility comparable to the lungs? A computer model approach

Abstract

Cell exposure experiments at the air-liquid interface (ALI) are used increasingly as indicators for health effects and for the impact of aerosols on the lung. Thereby the aerosol particles are kept airborne and can deposit on a cell surface area similar to the human respiratory tract (RT). However, geometry and air flow rates of an ALI system deviate considerably from the RT. As the tissue-delivered particle dose to the lungs (TD) can hardly be measured, computer models of particle deposition are used here to mimic both the particle deposition at ALI and in the RT. An ALI exposure setup (VitroCell GmbH) for an airflow rate of 100 cm³ min^?1 is selected, where the particle deposition model has been verified experimentally. For the RT we use the hygroscopic lung deposition model of Ferron et al. (2013 Ferron, G. A., S. Upadhyay, R. Zimmermann, and E. Karg. 2013. Model of the deposition of aerosol particles in the respiratory tract of the rat. II. Hygroscopic particle deposition. J. Aerosol Med. Pulm. Drug Deliv. 26 (2):101–19. doi:10.1089/jamp.2011.0965.[Crossref], [PubMed], [Web of Science ®] , [Google Scholar]). Model runs are performed for the particle deposition and for the deposited particles per surface area in both the ALI and the RT. The results show that the ALI-deposited mass is 1-2 orders of magnitude higher than in the alveolar region, because the surface area of the lung region is substantially larger. A particle size range from 40 to 450 nm is identified, where the ratio of both the deposition in a lung region and the deposition at the ALI varies by a factor less than two. Mean values for this ratio are 31 and 101 for the tracheo-bronchial and the alveolar region, respectively. The same size range is found for the ratio of the deposited particles per surface area in a lung region and at the ALI. For this range the mean surface deposition at the ALI is 23- and 1575-times larger than in the tracheo-bronchial and the alveolar lung region, respectively. The effect is partly compensated by different flow rate and cell size.

Copyright © 2020 American Association for Aerosol Research     

Oxide ceramic fibers via dry spinning process—From lab to fab

Oxide fibers preparation and manufacturing capabilities at Fraunhofer-Center HTL are introduced, showing the development and preparation of oxide ceramic fibers from lab scale to pilot scale up to near production scale. As a specific example, the development of an aluminosilicate fiber with mullite composition is discussed in more detail. Fiber development started from nonaqueous sol-gel precursors in the early lab scale. With increasing fiber spinning volume, precursors were switched to water-soluble systems. Transformation from green fiber to ceramic fiber was monitored by thermogravimetric and differential thermal analysis, X-ray diffraction, and scanning electron microscopy. The evolution of ceramic phases, microstructure formation, and the effects on tensile strength and Young's modulus were investigated. Weibull statistics and fracture analysis helped to understand the results. Next step will be the transition from large lab scale to pilot scale, demonstrating manufacturing capability.     

SiCN ceramics with controllable carbon nanomaterials for electromagnetic absorption performance

Different kinds of carbon nanomaterials, free carbon (C_free), graphene, and N-containing graphene (NG), in single-source-precursors-derived SiCN ceramics, were in situ generated by modifying polysilazane with divinylbenzene, dopamine hydrochloride and melamine, respectively. Adjusting the carbon source brings phase structure and electromagnetic wave absorption (EMA) properties differences of SiCN/C ceramics. In situ C_free enhances the EMA capacity of SiCN ceramics by improving their electrical conductivity of 9.2 × 10⁻⁴ S/cm. The electrical conductivity of SiCN ceramics with 2D graphene sheets balloons to 2.5 × 10⁻³ S/cm, causing poor impedance match thus leading to a worse EMA performance. In situ NG in SiCN ceramics has a low electrical conductivity of 5.6 × 10⁻⁸ S/cm, making for excellent impedance match. The corrugated NG boosts dielectric loss, interfacial, and dipole polarization. NG-SiCN nanocomposites possess an outstanding EMA performance with RL_min of −61.08 dB and effective absorption bandwidth of 4.05 GHz, which are ∼2.4 times lower and ∼4 times higher than those of SiCN, respectively.     

A Novel Coenzyme A Analogue in the Anaerobic,Sulfate-Reducing,Marine Bacterium Desulfobacula toluolica Tol2T

Coenzyme A (CoA) thioesters are formed during anabolic and catabolic reactions in every organism. Degradation pathways of growth-supporting substrates in bacteria can be predicted by differential proteogenomic studies. Direct detection of proposed metabolites such as CoA thioesters by high-performance liquid chromatography coupled with high-resolution mass spectrometry can confirm the reaction sequence and demonstrate the activity of these degradation pathways. In the metabolomes of the anaerobic sulfate-reducing bacterium Desulfobacula toluolica Tol2^T grown with different substrates various CoA thioesters, derived from amino acid, fatty acid or alcohol metabolism, have been detected. Additionally, the cell extracts of this bacterium revealed a number of CoA analogues with molecular masses increased by 1 dalton. By comparing the chromatographic and mass spectrometric properties of synthetic reference standards with those of compounds detected in cell extracts of D. toluolica Tol2^T and by performing co-injection experiments, these analogues were identified as inosino-CoAs. These CoA thioesters contain inosine instead of adenosine as the nucleoside. To the best of our knowledge, this finding represents the first detection of naturally occurring inosino-CoA analogues.     

Polysilazane derived micro/nano Si3N4/SiC composites

The pyrolised polysilazanes poly(hydridomethyl)silazane NCP 200 and poly(urea)silazane CERASET derived Si–C–N amorphous powders were used for preparation of micro/nano Si₃N₄/SiC composites by hot pressing. Y₂O₃–Al₂O₃ and Y₂O₃–Yb₂O₃ were used, as sintering aids. The resulting ceramic composites of all compositions were dense and polycrystalline with fine microstructure of average grain size <1 μm of both Si₃N₄ and SiC phases. The fine SiC nano-inclusions were identified within the Si₃N₄ micrograins. Phase composition of both composites consist of , β modifications of Si₃N₄ and SiC. High weight loss was observed during the hot pressing cycle, 12 and 19 wt.% for NCP 200 and CERASET precursors, respectively. The fracture toughness of both nanocomposites (NCP 2000 and CERASET derived) was not different. Indentation method measured values are from 5 to 6 MPa m^1/2, with respect to the sintering additive system. Fracture toughness is slightly sensitive to the SiC content of the nanocomposite. Hardness increases with the content of SiC in the nanocomposite. The highest hardness was achieved for pyrolysed CERASET precursor with 2 wt.% Y₂O₃ and 6 wt.% Yb₂O₃, HV 23 GPa. This is a consequence of the highest SiC content as well as the chemical composition of additives.     

Crystallization of Polymer-Derived Silicon Carbonitride at 1873 K under Nitrogen Overpressure

The chemical stability of an amorphous silicon carbonitride ceramic, having the composition 0.57SiC·0.43Si₃N₄·0.49C is studied as a function of nitrogen overpressure at 1873 K. The ceramic suffers a weight loss at p _N2 < 3.5 bar (1 bar = 100 kPa), does not show a weight change from 3.5 to 11 bar, and gains weight above 11 bar. The structure of the ceramic changes with pressure: it is crystalline from 1 to 6 bar, amorphous at ∼10 bar, and is crystalline above ∼10 bar. The weight-loss transition, at 3.5 bar, is in excellent agreement with the prediction from thermodynamic analysis when the activities of carbon, SiC, and Si₃N₄ are set equal to those of the crystalline forms; this implies that the material crystallizes before decomposition. The amorphous to crystalline transition that occurs at ∼10 bar, and which is accompanied by weight gain, is likely to have taken place by a different mechanism. A nucleation and growth reaction with the atmospheric nitrogen is proposed as the likely mechanism. The supersaturation required to nucleate α-Si₃N₄ crystals is calculated to be 30 kJ/mol.