Fluid dynamics and flow patterns in stirred tanks with a turbine impeller

Velocity profiles were measured in a stirred tank with a turbine impeller using a three-dimensional, pitot tube probe. A tangential jet model was used to describe the flow in the region of the impeller, and two-dimensional potential flow models and a circular jet were used to describe the flow in the rest of the tank. The tangential jet model accurately predicted the measurements from this work and comparable measurements reported in the literature for water and air, for varying impeller diameter and speeds and for different tank diameters. In the rest of the tank a three-dimensional, low velocity, flow field exists; and the center of circulation is not a true stagnation point. The flow at this point is tangential. The two-dimensional models only qualitatively described the flow in this region, and a three-dimensional model would be required. It was experimentally and theoretically confirmed that standard practice of using 10% baffles effectively controls the flow in the tank.     

Dependence of electrical properties of polycrystalline cvd si films on grain size and impurity doping concentrationa,b

The electrical properties of sets of simultaneously grown p-type polycrystalline Si films, deposited by SiH₄ pyrolysis on polycrystalline high-purity alumina substrates and B-doped during growth, were determined by Hall-effect measurements in the temperature range 77-420K as functions both of impurity doping concentration N (~10^l5 to ~10²⁰cm⁻³) and average grain size (≈1 to ≈125μm) in the film. Room temperature data showed rapidly increasing resistivities and rapidly decreasing free-carrier concentrations for doping below a critical concentration N_m and distinct mobility minima at that concentration, with the value of N_m being larger the smaller the average grain size. Measurements as a function of sample temperature showed the intergrain barrier height E_b, decreasing from a maximum value of ~0.4eV at the critical concentration to very small values (~0.01eV) for concentrations above 10¹⁹cm⁻³, with a functional dependence close to E_b ∝l/N^1/2 and E_b for any given concentration being larger the smaller the average grain size. Results are interpreted in terms of the grain-boundary trapping model. Trapped carrier densities in the grain boundaries were calculated to range from ~5×l0¹¹cm⁻² at N≈N_m to ~5×l0¹²cm⁻² for N>10¹⁹cm⁻³, the density being higher the smaller the grain size, and evidence was found for an energy distribution of traps in the Si bandgap, rather than a fixed density at a single discrete energy level. The observed relationship between N_m and average grain size nearly coincides with that of the model for films with ~lμm grain size but sharply departs from it for larger grain sizes, indicating probable applicability of the model for grain sizes up to that range. ^aThis work was supported by the U.S. Department of Energythrough its San Francisco Operations Office under Contract DE-AC03-79ET23045 and monitored by the Solar Energy Research Institute, Golden, CO. bThese results were first described at the 22nd Electronic Materials Conference, Ithaca, NY, June 21–27, 1980, Paper No. M4.     

Simple techniques for incorporating institutional-preference information in programming transportation investments

Urban transportation decisions usually involve a multiplicity of public and private institutions and actors. This paper addresses the problem of incorporating institutional preference information in a systematic manner within the methodology for evaluating transportation alternatives. An approach developed in conjunction with a procedure for programming major urban transportation network improvements in Cairo, Egypt is described. It relies on a measure of relative political desirability of alternative project combinations. Different possible types of preference information are compared as to information content and ease of implementation. Alternative analytical models of individual and group preferences towards project combinations under different preferential assumptions are specified and discussed. Finally, specifications are provided for their operational use in the application context for which they were intended.     

Minnesota Multiphasic Personality Inventory correlates of dysphasic language disturbances.

Compared the MMPI performances of 15 male dysphasic brain-damaged adults with the performances of 15 matched control brain-damaged Ss without specific language impairment. A significant overall difference on the 9 clinical scales combined was shown by multivariate analysis, with higher scores obtained by dysphasic Ss. Further univariate analysis showed significantly higher scores on the Pd and Sc scales. Results are discussed in terms of (a) evidence for a closer relation between MMPI variables and behavioral measures than between MMPI variables and neurological measures of lesion laterality, and (b) the interpretive limitations implied by uncritical transference of MMPI findings based on psychiatric patients and normals to patients with central nervous system lesions. The need for validation studies investigating social behavior correlates of MMPI results in brain-damaged samples is emphasized. (18 ref) (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

The removal of Escherichia coli-bacteriophage T7 by magnetic filtration

Magnetic filtration effectively removed bacteriophage T₇ from water. The removal was undertaken by adsorbing the virus onto magnetite in the presence of calcium chloride and by passing the mixture through a filter placed in a magnetic field.     

Estimation of safe exposure time from an ophthalmic operating microscope with regard to ultraviolet radiation and blue-light hazards to the eye

Hazards from the optical radiation of an operating microscope that cause damage at the corneal, lenticular, and retinal levels were investigated; we considered, in particular, ultraviolet radiation (UVR) and blue light. The spectral irradiance from a Zeiss operation microscope OPMI VISU 200 was measured in the corneal plane between 300 and 1100 nm. Effective irradiance and radiance were calculated with relative spectral effectiveness data from the American Conference for Governmental and Industrial Hygienists. Safe exposure time to avoid UVR injury to the lens and cornea was found to be 2 h without a filter, 4 h with a UVR filter, 200 a yellow filter, and 400 h with a filter combination. Safe exposure time to avoid retinal photochemical injury was found to be 3 min without a filter and with a UVR filter, 10 min with a yellow filter, and 49 min with a filter combination. The effective radiance limit for retinal thermal injury was not exceeded. The hazard due to the UVR component from the operating microscope is not critical, and operation time can be safely prolonged with the use of appropriate filters. The retinal photochemical hazard appears critical without appropriate filters, permitting only some minutes of safe exposure time. The calculated safe exposure times are for worst-case conditions and maximal light output and include a safety factor.     

Appearance-based face recognition and light-fields

Arguably the most important decision to be made when developing an object recognition algorithm is selecting the scene measurements or features on which to base the algorithm. In appearance-based object recognition, the features are chosen to be the pixel intensity values in an image of the object. These pixel intensities correspond directly to the radiance of light emitted from the object along certain rays in space. The set of all such radiance values over all possible rays is known as the plenoptic function or light-field. In this paper, we develop a theory of appearance-based object recognition from light-fields. This theory leads directly to an algorithm for face recognition across pose that uses as many images of the face as are available, from one upwards. All of the pixels, whichever image they come from, are treated equally and used to estimate the (eigen) light-field of the object. The eigen light-field is then used as the set of features on which to base recognition, analogously to how the pixel intensities are used in appearance-based face and object recognition.     

Determination of methionine and selenomethionine in yeast by species-specific isotope dilution GC/MS

A method for the simultaneous determination of methionine (Met) and selenomethionine (SeMet) in yeast using species-specific isotope dilution (ID) gas chromatography/mass spectrometry (GC/MS) is described. Samples were digested by refluxing for 16 h with 4 M methanesulfonic acid. Analytes were derivatized with methyl chloroformate and extracted into chloroform for GC/MS analysis. In addition to use of commercially available 13C-enriched Met and SeMet spikes for species specific ID analysis, a 74Se-enriched SeMet spike was also available for comparison of results. In selective ion monitoring mode, the intensities of ions at m/z 221, 222, 269, 270, and 263 were used to calculate the 221/222, 269/270, and 269/263 ion ratios for quantification of Met and SeMet. Concentrations of 5959 +/- 33 and 3404 +/- 12 microg g(-1) (one standard deviation, n = 6) with relative standard deviations of 0.55 and 0.36% for Met and SeMet, respectively, were obtained using 13C-enriched spikes. A concentration of 3417 +/- 8 microg g(-1) (one standard deviation, n = 6) was obtained using the 74Se-enriched SeMet spike. The concentration of SeMet measured in the yeast is equivalent to 66.43 +/- 0.24% of total Se and 30.31 +/- 0.11% of total Met is in the form of SeMet. Method detection limits (three times the standard deviation) of 3.4 and 1.0 microg g(-1) were estimated for Met and SeMet, respectively, based on a 0.25-g subsample of yeast with 1 mL of extract used for derivatization. A similar concentration of 5930 +/- 29 microg g(-1) (one standard deviation, n = 4) for Met and a lower concentration of 2787 +/- 49 microg g(-1) (one standard deviation, n = 4) for SeMet were obtained for this yeast sample using species-specific ID analysis based on GC/MS with 13C-enriched Met and SeMet spikes when a 2-h open microwave digestion approach using 8 M methanesulfonic acid was used.     

Standards for standard-makers? A testing time

The International Commission on Radiological Protection (ICRP) is now reviewing its recommendations with a view to publishing their revision in 2005. The last set of recommendations issued by the ICRP has caused some concern to neutron dosimetrists. This paper attempts to explain these concerns. Technological developments make it likely that exposure to high-linear energy transfer (LET) radiations will increase in the future. It is in the area of the dosimetry of high-LET radiations, particularly neutrons, where some experts feel that ICRP recommendations have been unclear. This paper discusses the process of setting protection limits in toxicology and its application to radiation protection. The development of radiation protection quantities and models is described, and the problems found with effective dose described. Suggestions for improvements are made that would enable effective dose to serve in two modes--both as a limiting quantity and also as the measurable (operational) quantity required by dosimetrists.