Modeling Microwave Vacuum Drying Kinetics and Moisture Diffusivity of Carrot Slices

Carrot slices of 3.5 mm thickness were dried in a laboratory microwave vacuum dryer at five different microwave power density levels of 2, 4.66, 7.33, 10, and 12.66 W/g and at three vacuum chamber pressure levels of 6.66, 19.98, and 33.3 kPa to 4-6% d.b. moisture content. Inside the dryer the sample holding plate was rotated with the speed of 4 rpm for uniform microwaves application. The drying rates were increased with the increase in microwave power density at all pressure levels and the Page model was found to be the most suitable model to predict the drying behavior of carrot slices at all process conditions. The Page model drying rate constant (k, min^-1) showed high correlation with microwave power density at constant pressure by a power law equation and showed a logarithmic relationship with the microwave power density and pressure. Similar to the drying rate constant, the average moisture diffusivity at constant pressure was found to be function of microwave power density by power law equation as well as was also dependent on the power density and pressure by a logarithmic relationship.     

Establishment of human parotid pleomorphic adenoma cells in culture: morphological and biochemical characterization

This study reports the establishment of alpha-amylase-producing human parotid pleomorphic adenoma cell lines (2HP and 2HP1) which have been maintained in culture for over 1 yr. The procedures required preparation of cellular clumps from tumor tissue and plating them on plasma clot or precoated dishes. During the initial phase of growth they required modified MCDB-153 medium without serum. When cells showed signs of degeneration they were changed to MCDB-153 medium containing first 2% and then 10% heat inactivated fetal bovine serum. Although cells grew well in MCDB-153 containing 10% serum, the epithelial cell morphology was not distinct. Therefore, the growth and morphology of cells grown in MCDB-10% serum were compared with those in RPMI growth medium containing 10% fetal bovine serum and F12 containing 10% agammaglobulin newborn bovine serum. Although the growth of cells was a little slower in F12 medium than those in MCDB and RPMI, the epithelial cell morphology was maintained better than in other growth media. The cells of 2HP and 2HP1 produce low levels of alpha-amylase and relatively high levels of alpha-amylase mRNAs of 1176 and 702 bp and contain neurofilament-160, a neuronal-specific marker. The cells of 2HP1 are tumorigenic when tested in athymic mice, but the cells of 2HP are not. The establishment of amylase-producing human parotid adenoma cell lines of different characteristics in culture provides a new opportunity to study the mechanisms of differentiation and transformation, and regulation of alpha-amylase in these cells.     

A three-parameter equation for molecular weight distribution of low-density polyethylene

A new three-parameter distribution function is proposed which fits best the experimental molecular weight distribution curves of branched lowdensity polyethylenes. The data were interpreted from GPC measurements, and a special computer program was utilized in order to derive the best values of the empirical constants a, b, and c.     

Model for drying during fluidized-bed combustion of wet low-rank coals

An unsteady state heat conduction model with a convective boundary condition is proposed for the drying of low-rank, high-porosity coals, such as lignites, during fluidized-bed combustion. The drying front is assumed to be the receding surface of a wet core. The solution technique for this moving boundary problem is based on the heat balance integral approach with immobilization of the moving boundary by a change in space variable. The governing cubic equation describing the drying curve in dimensionless form may be solved easily by the Newton—Raphson method. The model predictions are compared with experimental data for Mississippi lignite with excellent agreement. A correlation for estimation of total drying time is proposed. The temperature profiles obtained may be used for the study of the coupled drying and devolatilization in fluidized-bed combustors. The profiles could also be of importance in the study of formation of fissures/cracks in lignites subjected to intense heating conditions encountered during fluidized-bed combustion.     

THERMAL REGENERATION OF ACTIVATED CARBONS

The thermal regeneration of activated carbons loaded with p-nitrophenol (PNP) and other aromatic compounds was studied using a thermal balance. After pyrolysis of the adsorbates in nitrogen at 700°C, the residues were gasified with oxygen at 415 to 500°C or with steam at 840 to 920°C. Residues from PNP were several times more reactive to oxygen than the base carbons and also showed greater chemisorption of oxygen. For steam gasification, only small differences between spent and fresh carbons were found.     

Characteristics and compositions ofCarissa spinarum,Leucaena leucocephala andPhysalis minima seeds and oils

The seeds and extracted oils ofCarissa spinarum (Apocynaceae), (I),Leucaena leucocephala (Leguminosae) (II) andPhysalis minima (Solanaceae) (III) were analyzed for characteristics and compositions. The seeds of I, II and III contained 22.4, 6.4 and 40.0% oil and 10.1, 27.6 and 17.9% protein, respectively. The oils of I, II and III had, respectively, iodine values 70.1, 113.5 and 122.5; saponification values 186, 188 and 189; unsaponifiable matter 5.2, 2.5 and 0.8%, and the following fatty acid compositions (area %): palmitic 12.6, 14.2, 10.5; stearic 7.6, 6.1, 8.6; oleic 72.7, 20.1, 17.3; linoleic 5.2, 53.8, 61.4; linolenic 0.9, 1.8, 0.0, and arachidic 1.0, 2.3, 0.0. II contained 1.7% lignoceric acid. III contained small amounts of hexadecenoic (0.1%), epoxy (0.6%) and hydroxy (1.5%) fatty acids.     

Localized swelling of Fe-Cr-Ni alloy rollers in high-temperature applications

Localized swelling has been observed in 24Cr-24Ni-Nb steel transportation rollers used in the normalizing furnace of a plate mill after prolonged service at high temperature. Due to high localized thermal and mechanical stresses, the chromia layer formed on the roller surface ruptures, exposing the roller substrate to furnace oxygen. Oxidation of second-phase carbides results in the formation of carbon monoxide at very high partial pressure. This leads to formation of voids, leading in turn to localized swelling of the roller material.     

Updating a 1950s-generation aluminum smelter

Hindalco’s aluminum electrolysis cells were initially installed in 1962, and the technology was based on 1950s-generation pots. Although Hindalco expanded its aluminums melting capacity from 20,000 tonnes per year to 175,000 tonnes per year, the basic design of the pots remained unchanged. In view of energy price increases, and to keep pace with the latest developments in aluminum smelting technology, Hindalco undertook efforts to modernize its facilities. In spite of numerous constraints, the Hindalco smelter has been able to achieve performance nearly equivalent to that of 1980s-generation pots by retrofitting new technologies. This has resulted in considerable savings in electrical energy consumption and raw materials usage.     

A proposal for student modeling based on ontologies and diagnosis rules

The advances in the educational field and the high complexity of student modeling have provoked it to be one of the aspects more investigated in Intelligent Tutoring Systems (ITSs). The Student Models (SMs) should not only represent the student’s knowledge, but rather they should reflect, as faithfully as possible, the student’s reasoning process. To facilitate this goal, in this article a new approach to student modeling is proposed that benefits from the advantages of Ontological Engineering, advancing in the pursue of a more granular and complete knowledge representation. It’s focused, mainly, on the SM cognitive diagnosis process, and we present a method providing a rich diagnosis about the student’s knowledge state – especially, about the state of learning objectives reached or not. The main goal is to achieve SMs with a good adaptability to the student’s features and a high flexibility for its integration in varied ITSs.