La<Subscript>1−x</Subscript>Ag<Subscript>x</Subscript>FeO<Subscript>3</Subscript>/halloysites nanocomposite with enhanced visible light photocatalytic performance

La_1?xAg_xFeO₃/halloysites nanotubes (HNTs) nanocomposite was synthesized by sol–gel method. It was characterized by X-ray diffraction, transmission electron microscope, Fourier transform infrared spectroscopy and UV–visible diffused reflectance spectroscopy measurements. The photo-activity of the La_1?xAg_xFeO₃/HNTs nanocomposite was evaluated via degradation of methylene blue (MB) under visible-light irradiation. The results showed that the HNTs with unique pore structure favored the adsorption of organic molecules. Adequate Ag⁺ doping improved the absorption ability for visible light. The La_0.95Ag_0.05FeO₃/HNTs demonstrated the best photocatalytic performance, which achieved as high as 99 % for MB degradation exposed 2 h irradiation. However,further increasing of Ag⁺ doping gradually reduced the photocatalytic activity. The nanocomposite catalyst showed outstanding recyclability after eight cycles which still remained up to 90 %.     

Effect of sintering temperature on microstructures and microwave dielectric properties of Ba<Subscript>2</Subscript>MgWO<Subscript>6</Subscript> ceramics

The microwave dielectric properties of Ba₂MgWO₆ ceramics were investigated with a view to the use of such ceramics in mobile communication. Ba₂MgWO₆ ceramics were prepared using the conventional solid-state method with various sintering temperatures. Dielectric constants (? _r ) of 16.8–18.2 and unloaded quality factor (Q _u  × f) of 7000–118,200 GHz were obtained at sintering temperatures in the range 1450–1650 °C for 2 h. A maximum apparent density of 6.76 g/cm³ was obtained for Ba₂MgWO₆ ceramic, sintered at 1650 °C for 2 h. A dielectric constant (? _r ) of 18.4, an unloaded quality factor (Q _u  × f) of 118,200 GHz, and a temperature coefficient of resonant frequency (τ _f ) of ?34 ppm/°C were obtained when Ba₂MgWO₆ ceramics were sintered at 1650 °C for 2 h.     

Electromigration effect on Sn-58 % Bi solder joints with various substrate metallizations under current stress

The electromigration behavior of low-melting temperature Sn-58Bi (in wt%) solder joints was investigated with a high current density between 3 and 4.5 × 10³ A/cm² between 80 and 110 °C. In order to analyze the impact of various substrate metallizations on the electromigration performance of the Sn-58Bi joint, we used representative substrate metallizations including electroless nickel immersion gold (ENIG), electroless nickel electroless palladium immersion gold (ENEPIG), and organic solderability preservatives (OSP). As the applied current density increased, the time to failure (TTF) for electromigration decreased regardless of the temperature or substrate metallizations. In addition, the TTF slightly decreased with increasing temperature. The substrate metallization significantly affected the TTF for the electromigration behavior of the Sn-58Bi solder joints. The substrate metallizations for electromigration performance of the Sn-58Bi solder are ranked in the following order: OSP-Cu, ENEPIG, and ENIG. Due to the polarity effect, current stressing enhanced the fast growth of intermetallic compounds (IMCs) at the anode interface. Cracks occurred at the Ni₃Sn₄ + Ni₃P IMC/Cu interfaces on the cathode sides in the Sn-58Bi/ENIG joint and the Sn-58Bi/ENEPIG joint; this was caused by the complete consumption of the Ni(P) layer. Alternatively, failure occurred via deformation of the bulk solder in the Sn-58Bi/OSP-Cu joint. The experimental results confirmed that the electromigration reliability of the Sn-58Bi/OSP-Cu joint was superior to those of the Sn-58Bi/ENIG or Sn-58Bi/ENEPIG joints.     

A Microwave Transmission Instrument for Rapid Dry Rubber Content Determination in Natural Rubber Latex

We report the design, implementation and testing of an instrument for rapid dry rubber content (DRC) determination in rubber latex. It is composed of rectangular waveguide antennae, microwave generator, power detector, and microcontroller. According to the theory of microwave transmission, the power loss of microwaves passing through latex is related to the DRC. This attenuation is determined by measuring the transmitted microwave intensity with a power detector. The appropriate frequency that gives the best correlation between DRC and attenuation was found to be about 2.36 GHz. The microwave power measurement is processed by the microcontroller using the empirical calibration equation to estimate DRC in rubber latex. The instrument was tested using new latex samples with various DRC, sampled locally in Songkhla province, Thailand, and the DRC estimates by the instrument were compared to the slow but accurate standard oven-drying results. The estimates had an 0.21 % mean error and R ² = 0.9983, indicating good practical performance.     

An Approach Method to Calibrate the Autocollimator with Small Angle Measurement Range

A new method to calibrate the autocollimator with small angle measurement range has been developed. This method used a system based on rotary encoder for angle measurements with self-calibration function (SelfA47). The SelfA47 has 18,000 graduation lines with angle interval of 0.02°, corresponds to 72 arcsec. Thereby this system cannot be used to calibrate the autocollimator with measurement range <72 arcsec. On the other hand, SelfA47 can be used to calibrate an electronic level. The deviation of electronic level shaped linear gradient. Therefore a small nominal gradient of electronic level can be approximated by interpolation. Since the gradient of a curve corresponds to the angle quantities, it is feasible to calibrate the autocollimator with nominal angle <72 arcsec using SelfA47 and an electronic level. In this proposed method, SelfA47 is placed horizontally on the same plane with electronic level and mirror reflector position. The electronic level value that have been corrected by SelfA47 is used as a reference. This reference value was converted to the angle, thus the angle deviation of autocollimator can be determined. The prominent uncertainty of angle measurement using this new technique derived from the uncertainty of electronic level and rotary encoder. Using this method, the expanded uncertainty of 0.36 arcsec is obtained from calibration of autocollimator with measuring range of ±20 arcsec and it is consistent statistically with the manufacturer calibration result shown by E _n value is <1. In conclusion, this approach method can be applied to calibrate the autocollimator with a resolution smaller than SelfA47 as standard, but it is not recommended for the calibration of highly accurate autocollimator.     

Design and Uncertainty Evaluation of a Strain Measurement System

Strain measurement is very important in various industrial applications as well as different disciplines of science and technology for direct and indirect observations of certain parameters. Designing signal conditioning circuit is always a challenging and important task for satisfactory and reliable performance of a sensor as well as the system. The design and implementation details of a signal conditioning circuit of resistive sensor (strain gauge) for strain measurement are presented in this paper. Also the important aspects in designing a signal conditioning circuit for resistive sensor are presented and a novel method for the measurement of strain is discussed. Quarter bridge configuration with AC voltage excitation is used for the measurement along with the necessary circuitry to get a suitable and measurable output DC voltage. The measurement system is calibrated using a cantilever of stainless steel and the details of calibration are presented in the paper. The uncertainty associated with the measurement system is evaluated.     

Facile synthesis and characterization of MnO<Subscript>2</Subscript> nanomaterials as supercapacitor electrode materials

MnO₂ nanomaterials are synthesized via calcinations in air at various temperatures. Amorphous MnO₂ masses appear between 100 and 300 °C and nanorods form above 400 °C. Transmission and scanning electron microscopy are used to observe the geometries of each material, with further structural analyses conducted using X-ray photoelectron spectroscopy, X-ray diffraction, and BET method. The electrochemical properties are investigated through galvanostatic charge/discharge cycling, electrochemical impedance spectra, and cyclic voltammetry within a three-electrode test cell filled with 1 mol L^?1 Na₂SO₄ solution. The slightly asymmetric galvanostatic cycling curves suggest that the reversibility of the Faradaic reactions are imperfect, requiring a larger time to charge than discharge. The specific capacitances of each sample are calculated and trends are identified, proving that the samples synthesized at higher temperatures exhibit poorer electrochemical behaviors. The highest calculated specific capacitance is 175 F g^?1 by the sample calcinated at 400 °C. However, the lower temperature samples exhibit more favorable geometric properties and higher overall average specific capacitances. For future research, it is suggested that surface modifications such as a carbon coating could be used in conjunction with the MnO₂ nanorods to reach the electrochemical properties required by contemporary industrial applications.     

Preparation and microwave absorbing properties of nickel-coated carbon fiber with polyaniline via in situ polymerization

Electric conductive and microwave absorbing material PANI/Ni/CF was prepared by in situ polymerization of polyaniline on the surface of nickel-coated carbon fiber (Ni/CF). The morphologies and structures of CF, Ni/CF, PANI and PANI/Ni/CF were characterized by scanning electron microscope and X-ray diffraction. Results show that the CF was wrapped tightly around the nickel layer, and the Ni/CF was coated by PANI. Measurement of four probes resistance tester indicates that the electrical conductivity of PANI/Ni/CF was great improved compared with PANI and PANI/CF. Vibrating sample magnetometry shows that the magnetic saturation intensity of Ni/CF and PANI/Ni/CF was 13.8 and 2.3 emu/g, respectively. According to the vector network analyzer, the microwave absorbing properties of PANI/Ni/CF were better than those of PANI and PANI/CF, and its minimum loss value is ?12.4 dB at 8.8 GHz.     

Whisker growth on SnAgCu–xPr solders in electronic packaging

The addition of rare earth Pr into Sn3.8Ag0.7Cu solder results in the formation of PrSn₃ phase, which can induce the whiskers growth. After several hours’ exposure at room temperature in air, different morphologies of whiskers appear in the regions of PrSn₃ intermetallic compounds. The Pr content and storage time are the main parameters for affecting the whiskers growth at ambient temperature. The oxidation mechanism of PrSn₃ phase was used to explain the whiskers growth, the compressive stress is proposed as the driving force for whisker growth.     

Hydrothermal synthesis of zirconium oxide nanoparticles and its characterization

The paper presents the preparation and investigations of zirconium oxide (ZrO₂) nanoparticles that were synthesized by hydrothermal method. The products were characterized by means of powder X-ray diffraction, scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-absorption spectroscopy and photoluminescence (PL) spectroscopy. The crystal structure was determined using X-ray diffraction. The morphology and the particle size were studied using (SEM) and (TEM). The spherical shaped particles were confirmed through the SEM analysis. The transmission electron microscopic analysis confirmed the formation of the nanoparticles with the particle size. The FT-IR and Raman spectrum ascertained the strong presence of ZrO₂ nanoparticles. The optical properties were obtained from UV–visible absorption spectrum and also PL emission spectrum. The dielectric constant and the dielectric loss were measured as a function of frequency and temperature.