Tensile performance and crack propagation of coated woven fabrics under multiaxial loads

The tensile performance of coated woven fabrics under multiaxial loads is examined in the present study. Two groups of experiments were conducted to investigate the influences of the configuration of the fabric specimen and the loading speed on the multiaxial tensile properties of the fabrics. The configuration of the specimen for the multiaxial tensile tests is identified as gear‐shape with large arm widths. A loading speed of lower than 20 mm/min is suggested to obtain the tensile properties of the coated woven fabrics under multiaxial loads. The tensile performances of coated woven fabrics under uni‐, bi‐, and multiaxial loads were compared. We found that the tensile performances under bi‐ and multiaxial loads are much better than those under uniaxial loads. Therefore, for the application of the coated woven fabrics in lightweight structures, biaxial or multiaxial loading conditions will be necessary. Experiments on the specimens with an initial crack in the center under multiaxial loads show that, by comparison with other loading directions, the tensile properties in warp direction of the coated woven fabrics play an important role in the failure performance and crack propagation under multiaxial loads. To eliminate the dependence on the mechanical properties in warp direction, the balance of the two principle directions of coated woven fabrics should be improved. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Optimization of stormwater filtration at the urban/watershed interface

Environmental pollution from cities is a major ecological problem attributed to contaminated runoff from nonpoint sources. The U.S. Environmental Protection Agency's guidance on implementation of total maximum daily loads (TMDL) does not adequately cover methods to improve waters impaired by nonpoint sources. To comply with TMDLs, cities may install filters in curb inlets, or use other Best Management Practices (BMPs). We tested 10 different filters and found their effectiveness in retaining pollutants ranged from 0 to >90%, depending on combinations of pollutant types (metals, pathogens, and total suspended sediments (TSS)) and filter materials. Hence, the decision to deploy filters into curb inlets must consider land use patterns associated with specific categories of pollutants generated within cities. We developed a geographic information system (GIS)-enabled model for estimating and mitigating emissions of pollutants from urban regions into watersheds. The model uses land use categories and pollutant loadings to optimize strategic placement of filters to accommodate TMDLs. For example, in a city where the landuse pattern generates 4 x 10(6) kg of TSS, 55 kg of Cd, and 2 x 10(3) kg of Zn per year into 498 curb inlets that discharge into a sensitive watershed, the optimized placement of 137, 92, and 148 filters can achieve TMDL endpoints for each pollutant, respectively. We show further that 158 strategically placed filters effectively meet the requirements simultaneously for all three pollutants, a result at least 5 times more effective than random placement of filters.     

Mitotic, but not meiotic, oriented cell divisions in rat spermatogenesis

The process of mammalian spermatogenesis involves both mitosis and meiosis at the same developmental age. Most previous studies have focused on mitotic spindle orientation during development, but not during meiotic division. Therefore, we asked whether there is a difference between mitotic and meiotic germ cell spindle orientation during rat spermatogenesis. Our results showed that mitotic spindles of spermatogonia were mainly oriented with angles ranging from 60 to 90 degrees, perpendicular in relation to the basement membrane of the seminiferous tubules. On the other hand, meiotic spindles showed a random orientation. Nocodazole treatment (at a concentration that depolymerizes only astral microtubules) induced a significant increase in cells with an angle between 0 and 30 degrees (parallel) in relation to the basement membrane. Meiotic spindles did not show a significant change in their orientation after the Nocodazole treatment. Therefore, our results suggest differences between the mechanisms controlling positioning and orientation of mitotic and meiotic spindles during rat spermatogenesis. It seems that a phylogenetically conserved programme controls the mitotic spindle orientation in organisms ranging from worms to mammals.     

Aerobic Training in Young Men Increases the Transfer of Cholesterol to High Density Lipoprotein In Vitro: Impact of High Density Lipoprotein Size

Exercise training not only improves the plasma lipid profile but also reduces risk of developing coronary heart disease. We investigate whether plasma lipids and high density lipoprotein (HDL) metabolism are affected by aerobic training and whether the high-density lipoprotein cholesterol (HDL-C) levels at baseline influence exercise-induced changes in HDL. Seventy-one male sedentary volunteers were evaluated and allocated in two subgroups, according to the HLD-C levels (< or >40 mg/dL). Participants underwent an 18-week aerobic training period. Blood was sampled before and after training for biochemical analysis. Plasma lipids, apolipoproteins, HDL diameter, and VO₂ peak were determined. Lipid transfers to HDL were determined in vitro by incubating plasma samples with a donor lipid artificial nanoemulsion. After the 18-week period of aerobic training, the VO₂ peak increased, while the mean body mass index (BMI) decreased. HDL-C concentration was higher after the training period, but low-density lipoprotein cholesterol (LDL-C) and non-HDL-C did not change. The transfer of esterified cholesterol and phospholipids was greater after exercise training, but the triacylglycerol and unesterified cholesterol transfers were unchanged. The HDL particle diameter increased after aerobic training in all participants. When the participants were separated in low-HDL and normal-HDL groups, the postaerobic exercise increment in HDL-C was higher in the low-HDL group, while the transfer of esterified cholesterol was lower. In conclusion, aerobic exercise training increases the lipid transfers to HDL, as measured by an in vitro method, which possibly contributes to the classical elevation of the HDL-C associated with training.     

Electrodes based on nano-tree-like vanadium nitride and carbon nanotubes for micro-supercapacitors

Vanadium nitride(VN) was deposited by DC-sputtering on a vertically aligned carbon nanotube(CNTs)template for the purpose of nano-structuration. This led to the fabrication of hierarchically composite electrodes consisting of porous and nanostructured VN grown on vertically aligned CNTs in a nano-treelike configuration for micro-supercapacitor application. The electrodes show excellent performance with an areal capacitance as high as 37.5 m F cm~(-2) at a scan rate of 2 mV s~(-1) in a 0.5 MK_2SO_4 mild electrolyte solution. Furthermore, the capacitance decay was only 15% after 20,000 consecutive cycles. Moreover,the capacitance was found to increase with VN deposit thickness. The X-ray photoelectron spectroscopy analyses of the electrodes before and after cycling suggest that the oxide layers that form at the VN surface is the responsible for the redox energy storage in this material. Such electrodes can compete with other transition metal nitride based electrodes for micro-supercapacitors.     

Ultra-Robust Flexible Electronics by Laser-Driven Polymer-Nanomaterials Integration

Polyethylene terephthalate (PET) is the most widely used polymer in the world. For the first time, the laser-driven integration of aluminum nanoparticles (Al NPs) into PET to realize a laser-induced graphene/Al NPs/polymer composite, which demonstrates excellent toughness and high electrical conductivity with the formation of aluminum carbide into the polymer is shown. The conductive structures show an impressive mechanical resistance against >10000 bending cycles, projectile impact, hammering, abrasion, and structural and chemical stability when in contact with different solvents (ethanol, water, and aqueous electrolytes). Devices including thermal heaters, carbon electrodes for energy storage, electrochemical and bending sensors show this technology's practical application for ultra-robust polymer electronics. This laser-based technology can be extended to integrating other nanomaterials and create hybrid graphene-based structures with excellent properties in a wide range of flexible electronics’ applications.     

A simple improvement of a tip loss model for actuator disc simulations

The loading of a wind turbine decreases towards the blade tip because of the velocities induced by the tip vortex. This tip loss effect has to be taken into account when performing actuator disc simulations, where the single blades of the turbine are not modeled. A widely used method applies a factor on the axial and tangential loading of the turbine. This factor decreases when approaching the blade tip. It has been shown that the factor should be different for the axial and tangential loading of the turbine to model the rotation of the resulting force vector at the airfoil sections caused by the induced velocity. The present article contains the derivation of a simple correction for the tangential load factor that takes this rotation into account. The correction does not need any additional curve fitting but just depends on the local airfoil characteristics and angle of attack. Actuator disc computations with the modified tip loss correction show improved agreement with results from actuator line, free wake lifting line, and blade element momentum simulations.