Role of Nd-Ni on structural,spectral and dielectric properties of strontium-barium based nano-sized X-type ferrites

The influence of neodymium and nickel substitution on structural and dielectric parameters was investigated in strontium-barium X-type hexagonal ferrites having composition SrBaCu_2?xNi_xNd_yFe_28?yO₄₆ (x = 0, 0.2, 0.4, 0.6, 0.8, 1 and y = 0, 0.02, 0.04, 0.06, 0.08, 0.1). Sol-gel method was employed for synthesizing these hexagonal ferrites. The XRD plots of all studied materials which were annealed at 1250 °C show single phase characteristics. Lattice parameter ‘c’ increased as a consequence of larger radius of rare earth ion (Nd³⁺) as compared to (Fe³⁺), while lattice parameter ‘a’ showed very small variation. The cell volume was obtained in the range 2508.32–2523.75 (ų). The inclusion of Nd-Ni also affected X-ray density, bulk density and porosity. The FTIR spectroscopy indicated the particular absorption peaks of hexagonal ferrites and it was performed in the range of 500–700 cm^?1. On account of Nd-Ni doping, the dielectric constant, dielectric loss and AC-conductivity showed decreasing trend. The occupancy of Nd³⁺ ions at octahedral site impedes the valence alternation of Fe³⁺; therefore there was decrease in dielectric permittivity. Ac conductivity has been decreased from 9.14 to 6.49 (Ω cm)^?1 at frequency of 2.7 GHz. The Cole-Cole plots of synthesized materials noticeably revealed grain boundary contribution. The appearance of single semi-circle in impedance Cole-Cole graphs confirms the exceptional role of grain boundaries in the conduction process. The considerably lower dielectric parameters of investigated nano X-type ferrites propose their feasibility for high-frequency applications (phase shifters, dielectric resonators, stealth technology etc).     

Technical and economic analysis of solvent-based lithium-ion electrode drying with water and NMP

Processing lithium-ion battery (LIB) electrode dispersions with water as the solvent during primary drying offers many advantages over N-methylpyrrolidone (NMP). An in-depth analysis of the comparative drying costs of LIB electrodes is discussed for both NMP- and water-based dispersion processing in terms of battery pack $/kWh. Electrode coating manufacturing and capital equipment cost savings are compared for water vs. conventional NMP organic solvent processing. A major finding of this work is that the total electrode manufacturing costs, whether water- or NMP-based, contribute about 8–9% of the total pack cost. However, it was found that up to a 2?×?reduction in electrode processing (drying and solvent recovery) cost can be expected along with a $3–6?M savings in associated plant capital equipment (for a plant producing 100,000 10-kWh Plug-in Hybrid Electric Vehicle (PHEV) batteries) using water as the electrode solvent. This paper shows a different perspective in that the most important benefits of aqueous electrode processing actually revolve around capital equipment savings and environmental stewardship and not processing cost savings.     

Soret and Dufour effects between two rectangular plane walls with heat source/sink

This study addresses the thermo‐diffusion and the diffusion‐thermo phenomena in a semi‐infinite absorbent channel whose walls are contracting/expanding, with heat source/sink effects. The governing partial differential equations with suitable boundary conditions are transformed to a system of dimensionless ordinary differential equations. An analytic solution of the problem has been found using a technique called homotopy analysis method (HAM). HAM gives consistently valid answers to the problem over an extensive variety of parameters and also provides better accuracy. To validate the analytical results, a comparison has been presented with a numerical solution calculated by using the parallel shooting method. The effects of dimensionless parameters, that is, deformation parameter, Reynolds number, Soret and Dufour numbers, and heat source/sink parameter on the expressions of velocity, temperature, and concentration profiles are analyzed graphically to understand the physics of the deformable channel. It has been noted that the velocity across the channel is higher for the expanding channel, as compared to that for the contracting channel. Also the Soret and Dufour number increases the temperature of the fluid, and decreases the concentration. The temperature profile has an increasing behavior in the case of heat source, and a decreasing behavior in the case of heat sink.     

Influence of Different Additives on the Interaction of Quinolone Antibiotic Drug with Surfactant: Conductivity and Cloud Point Measurement Study

Conductometric and cloud point (CP) measurement studies have been performed to investigate the interaction of tetradecyltrimethylammonium bromide (TTAB) and Triton® X-100 (TX-100) with ciprofloxacin hydrochloride (CFH) in different solvents over the temperature range of 295.15–315.15 K. CFH is used for the treatment of various bacterial infections. The observed critical micelle concentration (CMC) values of TTAB were found to be reduced in the presence of electrolytes (Na₂SO₄/Na₃PO₄), and this reduction proceeds with the elevation of salt concentration. The order of the CMC of TTAB follows the trend: > >. The observed CMC values of TTAB were found to increase with increasing temperature and decrease with increasing concentration of CFH in aqueous medium. The values of Gibbs free energy of micellization () for the TTAB/TTAB + CFH mixture were found to be negative, implying spontaneous micellization. The estimated CP of TX-100 decreases with increasing concentration of TX-100 in aqueous medium. The CP values first decrease with increasing concentration of CFH and then increase at higher concentration of CFH almost in all cases investigated. The values of free energy of clouding were found to be positive in all cases studied implying that phase separation of TX-100 was nonspontaneous. The other thermodynamic parameters associated with the micellization of TTAB and the phase separation of TX-100 were estimated and explained.     

Performance of a new pipe material UHMWPE against disinfectant decay in water distribution networks

Clean Technologies and Environmental Policy - The concentration of any disinfectant is a major parameter which is used to evaluate the quality of water. Chlorine is the most common disinfecting...     

Effect of ZnO layer thickness upon optoelectrical properties of NiO/ ZnO heterojunction prepared at room temperature

In this work, p-NiO/n-ZnO heterostructures were successfully prepared at room temperature using RF sputtering technique. The influence of ZnO layer thickness on the performance of the heterojunction was investigated. The deposited ZnO layers have a hexagonal Wurtzite structure with preferable growth orientations along (002) and (103) for thinner films. Increasing the thickness results in more crystallographic orientation randomness. The current–voltage measurements of the realized heterojunctions showed a clear rectifying behavior. The measured ideality factor varies from 2.5 to 1.6 according to the thickness of ZnO layer. The series resistance of the device is enlarged with increasing ZnO thickness. The deduced parameters from the I–V characteristics suggest that 200 nm is the optimal thickness of the ZnO layer according to our experimental conditions. We attribute the relatively better performance of this thickness to achieving reasonable compensation between serial resistance and ideality factor. The best heterojunction was tested and successfully used as a UV detector.     

Synthesis of amino-cosubstituted polyorganophosphazenes and fabrication of their nanoparticles for anticancer drug delivery

The development of safe drug carriers is cardinal in cancer therapy, which can target the cancer cells and release the loaded drug on-demand without damaging the healthy cells of the body. In our work, we synthesized three different biodegradable polymers, poly[(ethyl aminobezoate) (ethyl glycinato) phosphazenes] (PABGPs), in different mole ratio of side groups. The successful synthesis of these PABGPs was confirmed by ¹H NMR, ³¹P NMR, FT-IR, and gel permeation chromatography. These PABGPs were fabricated into drug (camptothecin, CPT, a hydrophobic anticancer drug) loaded nanoparticles. These drug-loaded nanoparticles showed good drug release behaviors under normal physiological conditions (pH 7.4 and temperature 37°C). These PABGPs-based nanoparticles may find their application as effective drug carriers for cancer therapy.     

Synthesis and characterization of conducting copolymers from aniline and o‐anisidine in HCl solutions

Conducting poly(aniline‐co‐o‐anisidine) (PAS) films with different ratios of aniline units in the polymer chain were prepared by oxidative polymerization of different molar ratios of aniline and o‐anisidine in 1 M HCl using cyclic voltammetry. Due to the much higher reactivity of o‐anisidine, the structure and properties of PASs were found to be dominated by the o‐anisidine units. The polymerization of poly‐o‐anisidine and PASs followed zero‐order kinetics with respect to formation of the polymer (film thickness) and the autocatalytic polymerization of aniline was completely inhibited. In contrast to polyaniline, a decrease in the polymerization temperature was found to increase the amount of copolymer formed and its redox charge. The presence of aniline units in PASs led to a pronounced increase in the molecular weight and conductivity, and a decrease in the solubility in organic solvents. Repetitive charging/discharging cycles showed that PASs resist degradation more than polyaniline. Copyright © 2003 Society of Chemical Industry     

Understanding the differences between how novice and experienced designers approach design tasks

Research was undertaken to understand how to provide the most appropriate support for novice designers in engineering design. However, how designers apply their experience and knowledge is not understood and further research in this area is required. This paper describes an observational study to understand how novice and experienced designers approach design tasks. Electronic Publication