低温脂肪酶产生菌的筛选、鉴定及其部分酶学性质

从南极乔治王岛冻土来源的76株低温细菌中筛选到13株低温脂肪酶产生菌，对其中的BTsl0022菌株进行鉴定。通过生理生化特征、16s rDNA基因序列的同源性和系统发育分析发现，菌株RTsl0022属于假单胞菌属(Pseudomonas)，但与已定名的假单胞菌有一定的差异，与未定名的Pseudomonas sp．PsB的亲缘关系最接近，故将其暂定名为Pseudomonas sp．BTsl0022。对该菌脂肪酶的酶学性质初步研究表明，酶的最适作用温度为24℃，对热敏感，60℃处理30min仅残留25％酶活性，酶的适宜作用pH范围在7．0～9．0，最适pH为8．0。     

复杂环境下的WCDMA网络精确规划探讨

首先介绍了传统规划方法，然后着重介绍了精确规划方法所采用的相关新技术，最后简要介绍了笔者应用仿真方法对实际工程进行检验的结果。     

Area- and time-specific marginal capacity costs of electricity distribution

Marginal costs of electricity vary by time and location. In the past, researchers attributed the variations to factors related to electricity generation and transmission. These authors, however, have not analyzed possible variations in marginal distribution capacity costs (MDCC). The objectives of this paper are:

1. (i) to show that large MDCC variations are due to the dispersion in distribution capital expenditures by time and space,

2. (ii) to propose a method for quantifying the area- and time-specific MDCC in the presence of lumpy investments, and

3. (iii) to compare our MDCC estimates to those commonly used in the electric utility industry.

Our proposed method and its results were adopted by the California Public Utilities Commission (CPUC) in 1992 for Pacific Gas and Electric Company (PG&E), the largest privately owned electric utility in the U.S.     

三峡水库减淤增容调度方式研究——多汛限水位调度方案

本文建议在汛期中小流量时（Q<35000m3/s），将坝前水位维持在148～151m；出现汛情且流量更较大后，将坝前水位降低到143m；入库流量大于35000m3/s且短期预报将出现大于十年一遇洪水时，预泄洪水到135m.按这一调度，汛期约80％时间可以维持在较高水位，一般洪水期。汛限水位143m不影响坝区通航，135m水位迎洪可大量增加防洪库客。到100年后可减淤30亿m3，增加防洪库容约40亿m3.变动回水区减淤40%，优化了坝区水沙搭配，可改善通航条件。降低库区洪水位，缓解防洪与移民的矛盾。可对发电带来较大好处：提高发电效益，减少粗沙过机。初期水库排沙比大于原方案，可减轻下游冲刷。同时，可减小三峡汛初泄水与鄱阳湖防洪的矛盾。     

自动力套管补贴加固技术及其在B125井的应用

随着油田开发时间的延长，油水井井下套管的损坏将越来越严重，套管故障井将越来越多，为了恢复套损井生产，将套管损坏所造成的损失降到最低，在配套波纹管补贴，水动力补贴，爆炸补贴等专门修套技术的基础上，通过认真调查研究，又配套了操作方便简单，适用套管损坏类型广的自动力套管补贴加固技术，使各种套管变形，套管断错（错开没有位移或位移量不大时）、套管破裂，误射孔井段封堵，已射开水层封堵等修井作业的难度进一步降低，从而进一步提高了修复井综合开发经济效益。     

编码解码芯片HD3-6408-9及其应用

编码解码芯片HD3 64 0 8 9是一种高性能的CMOS器件。这种大规模芯片主要由编码器和解码器两部分组成。在数据传输应用中 ,采用两个独立的单片机系统 ,利用编码解码芯片 (HD3 64 0 8 9)组成数字信号的接收、发送及显示部分来完成数据传输功能     

定向探测引信技术分析

从提高引信与战斗部配合效率出发 ,根据定向战斗部的战术技术性能 ,介绍了一种能够识别弹体周围 4个方向目标的定向探测引信 .分析了定向探测器的工作原理和目标方位识别的关键技术 ,并对探测天线的设计做了详细的分析和计算 .     

The influence of viewing distance on subjective impairment assessment

In this paper, the influence of viewing distance on subjective assessment of the impairment in video sequences is investigated. Subjective tests using the double-stimulus impairment scale variant II (DSIS II) method have been conducted at viewing distances of 5H (where H stands for the screen height) and 3H, respectively. Several statistical measures have been used to analyze the influence, including correlations and ANOVA (analysis of variance) tests. The results reveal that there is a very high correlation between the subjective scores, the variances are similar under the two viewing distances, the means of subjective data at these two viewing distances are the same, and there is no interaction between the viewing distance and the other two factors, i.e., the codec system and the source sequence. Throughout the tests, there is no evidence that a closer viewing distance such as 3H will vary the subjective test result statistically significantly.     

试论电信企业激励机制的改革与创新

本文分析了电信企业面临的社会经济新形势，揭示了在计划经济条件下电信企业内部激励机制存在的弊端，论述了电信企业进行激励机制改革与创新的必要性和必然性，提出了电信企业在生存和发展中改革与创新激励机制的指导思想及原则，提出了如何建立一套科学、合理的激励机制，以便更有效地发挥员工的积极性、主动性和创造性，最大程度地提高激励的效用。     

Effects of grain sizes, shapes, and distribution on minimum sizes of representative volume elements of cubic polycrystals

In the literature the concept of representative volume element (RVE) was introduced to correlate the effective or macroscopic properties of materials with the properties of the microscopic constituents and microscopic structures of the materials. However, to date little quantitative knowledge is available about minimum RVE sizes of various engineering materials. In our recent paper [J. Mech. Phys. Solids 50 (2002) 881], a new definition of minimum RVE size was introduced based on the concept of nominal modulus. Numerical experiments using the finite element method (FEM) were then carried out for determining the minimum RVE sizes of more than 500 cubic polycrystals in the plane stress problem, under the assumption that all grains in a polycrystal have the same square shape––called the simple polycrystal model. The major finding is that the minimum RVE sizes for effective elastic moduli have a roughly linear dependence on crystal anisotropy degrees. The present paper takes into account the effect of grain sizes, shapes, and distribution on the minimum RVE sizes for real cubic polycrystals that are formed by crystallization processes. Similar roughly linear dependence is found again, with the slope about 19% lower than that in the simple polycrystal model. This finding is interesting and useful because numerical experiments on minimum RVE sizes for a large number of crystals are quite time-consuming and the simple polycrystal model reduces significantly the FEM pre- and post-processing works. This should be particularly true in numerically testing minimum RVE sizes for three-dimensional polycrystals and for nonelastic properties in future works. With a maximum relative error 5%, all the polycrystals tested have a minimum RVE size of 16 or less times the grain size.