A rate equation for Ca(OH)2 and CO2 reaction in a spouted bed reactor at low gas concentrations

In the present study, the carbonation reaction of hydrated lime in semi-dry condition is investigated experimentally in a laboratory-scale spouted bed reactor. Results show that for operating conditions where the concentration of CO₂ is low, the capture efficiency is raised by increasing the inlet CO₂ concentration. Additionally, because of the inconsistency between the experimental reaction rate and the calculated values based on the previous proposed equations, a new rate equation is introduced that considers the dependency of CO₂ concentration too. To validate the proposed equation, its predictions were compared with another set of experimental data.     

Effect of surface tension gradient on gas hold-up enhancement in aqueous solutions of electrolytes

The effect of addition of electrolytes on gas hold-up of air/water system was investigated experimentally in a laboratory scale bubble column. The experiments were carried out with four electrolytes, namely, NaCl, MgSO₄·7H₂O, Na₂SO₄ and CaCl₂·2H₂O and the concentrations of the solutions were varied from 0 to 0.3 mol/l. Enhancement of gas hold-up was observed for all four electrolytes at concentrations less than 0.1 mol/l. With the increase in concentration, the gas hold-up showed two different trends; in Na₂SO₄ and CaCl₂·2H₂O solutions, gas hold-up formed a sharp peak after the enhancement and leveled off at a value somewhat higher than that in water, whereas in NaCl and MgSO₄·7H₂O solutions, gas hold-up leveled off immediately after the enhancement without forming any peak. Experiments were also conducted to measure the surface tensions of the solutions with special focus in the low concentration region. A strong relation between the gas hold-up enhancement and the change of surface tension with the addition of electrolyte was found. It was also observed that the concentration at which maximum value of C(dσ/dC)² i.e. (concentration × surface tension gradient with respect to concentration²) is obtained corresponds to the concentration at which maximum gas hold-up enhancement occurs.     

Resonant frequency of gold/polycarbonate hybrid nano resonators fabricated on plastics via nano-transfer printing

We report the fabrication of gold/polycarbonate (Au/PC) hybrid nano resonators on plastic substrates through a nano-transfer printing (nTP) technique, and the parametric studies of the resonant frequency of the resulting hybrid nano resonators. nTP is a nanofabrication technique that involves an assembly process by which a printable layer can be transferred from a transfer substrate to a device substrate. In this article, we applied nTP to fabricate Au/PC hybrid nano resonators on a PC substrate. When an AC voltage is applied, the nano resonator can be mechanically excited when the AC frequency reaches the resonant frequency of the nano resonator. We then performed systematic parametric studies to identify the parameters that govern the resonant frequency of the nano resonators, using finite element method. The quantitative results for a wide range of materials and geometries offer vital guidance to design hybrid nano resonators with a tunable resonant frequency in a range of more than three orders of magnitude (e.g., 10 KHz-100 MHz). Such nano resonators could find their potential applications in nano electromechanical devices. Fabricating hybrid nano resonators via nTP further demonstrates nTP as a potential fabrication technique to enable a low-cost and scalable roll-to-roll printing process of nanodevices.     

Effects of extraction temperature, extraction pressure and nozzle diameter on micronization of cholesterol by RESS process

Micronized cholesterol particles were produced via the Rapid Expansion of Supercritical CO₂ Solutions (RESS) process. Taguchi design was used for designing the experimental plan to investigate the effects of three parameters including extraction temperature (40-60 °C), extraction pressure (100-160 bar) and nozzle diameter (0.15-0.24 mm) on the size and morphology of the cholesterol particles produced by the RESS process. The characterization of the particles was carried out using scanning electron microscopy (SEM) and X-ray diffraction (XRD) measurements to evaluate the performance of RESS process. The average particle size of the original material was 55 μm ± (2.84) while the average particle size of cholesterol after size reduction via the RESS process was between the minimum of 0.62 μm ± (0.03) and the maximum of 4.83 μm ± (0.18) depending upon the experimental conditions used. It was observed that both increasing the temperature from 40 to 60 °C and increasing the nozzle diameter from 0.15 to 0.24 mm result a reducing effect on the average particle size, whereas extraction pressure (100-160 bar) change has slight effect on the average particle size.     

Application of polyaniline nanolayer composite for removal of tartrazine dye from aqueous solutions

In this research, polyaniline was synthesized chemically onto the surface of sawdust as a thin layer (termed as PAni/SD) and was then used for removal of tartrazine dye (a typical anionic azo dye) from aqueous solutions. Ammonium peroxodisulphate was used as chemical oxidant for polymerization of polyaniline directly on the surface of sawdust. The procedure involves sorption experiments were performed on both batch and column systems. The effects of some important parameters such as pH, initial concentration, sorbent dosage, exposure time and temperature on uptake of tartrazine dye were investigated. Adsorption studies have shown that pH of the tartrazine solution has influence on the dye removal capacity of PAni/SD. It was found that effective dye removal is occurred under neutral or acidic conditions. The treatments of the data were carried out using both Freundlich and Langmuir adsorption isotherms. Sorption/desorption studies showed that PAni/SD was fast, simple, inexpensive, highly efficient and potential re-usable adsorbent to remove tartrazine from aqueous solutions. Based on our kinetics and thermodynamic studies, it was found that sorption process was endothermic (ΔH > 0) and the experimental data fitted very well with pseudo second-order kinetic model.     

Improvement of Canola Oil Frying Stability by Bene Kernel Oil’s Unsaponifiable Matter

The anti-rancidity effect of the unsaponifiable matter fraction of bene kernel (UFB) oil on canola oil (CAO) during frying was compared to that of tert-butyl hydroquinone (TBHQ). The UFB was separated into hydrocarbons (12.9%), carotenes (9.6%), tocopherols and tocotrienols (65.8%, mainly γ-tocopherol), linear and triterpenic alcohols (3.8%), methyl sterols (2.8%), sterols (3.0%, mainly β-sitosterol, stigmasterol, Δ⁵-avenasterol, and Δ⁷-avenasterol, respectively), and triterpenic dialcohols (2.2%). The results obtained from the measurements of the total polar compounds, the conjugated diene value, the carbonyl value, and total tocopherols showed that the stability of CAO improves similarly in the presence of UFB or TBHQ, and even more in the presence of UFB in some cases (especially inhibition of oxidized triglyceride monomers and triglyceride dimers). The analysis of polar components showed that the antioxidative additives were more effective to resist the formation of thermo-oxidative than hydrolytic products during the frying of CAO.     

Hydrophilic modification of P(VDF-co-CTFE) porous membranes

This paper describes fabrication of a poly(vinylidene difluoride-co-chlorotrifluoroethylene) (P(VDF-co-CTFE)) porous membrane via non-solvent induced phase inversion and subsequent hydrophilic modification using high efficient surface initiated atom transfer radical polymerization (ATRP). The effect of viscosities of casting solutions on microstructures of the P(VDF-co-CTFE) membrane was investigated. The surface chemistry, thermal stability, morphological structure, and hydrophilicity of the modified membranes were evaluated by Fourier Transform Infrared Attenuated Total Reflection (FTIR-ATR), Differential Scanning Calorimeter (DSC), Scanning Electron Microscope (SEM), and contact angle measurements, respectively. The degree of grafting and the degree of swelling were measured to analyze the effect of polymerization time on the wettability. The mechanical strength of the membranes after modification was also investigated. The permeability and fouling resistance were evaluated according to pure water flux and protein solution filtration measurements. The results demonstrate that the hydrophobic P(VDF-co-CTFE) membrane can be feasibly modified by immobilization of hydrophilic poly(ethylene glycol) methyl ether methacrylate (PEGMA) brushes via surface initiated ATRP.     

Preparation and study of thermal properties of phase change materials based on paraffin–alumina‐filled polyethylene

Novel phase change materials based on paraffin and alumina‐filled polyethylene (FPE) were prepared using a two‐step process. In the first step, PE is synthesized using metallocene catalyst system. The synthesized PE is subsequently purified, whereas hydrated alumina–PE composites will be formed by the hydrolysis of aluminum organic cocatalyst and dispersion of hydrated alumina in the PE matrix. In the second step, paraffin–alumina‐FPE composites were prepared by using the ex situ technique. Scanning electron microscopy, X‐ray diffraction, Fourier‐transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry were used to evaluate the structure and thermal properties of the composites. The results show that the incorporation of a suitable amount of alumina into the composites changes their thermal stability. It is also possible to improve the thermophysical properties of the thermal energy storage materials by altering the paraffin ratio to the FPE. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Calorimetric and rheokinetic analyses merged to capture crystallization kinetics in polyamide/clay nanocomposites: Revisiting predictability of models

Crystallization kinetics of polymer/clay systems was the subject of numerous investigations, but still there are some ambiguities in understanding thermal behavior of such systems under isothermal and nonisothermal circumstances. In this work, isothermal rheokinetic and nonisothermal calorimetric analyses are combined to demonstrate crystallization kinetics of polyamide6/nanoclay (PA6/NC) nanocomposites. As the main outcome of this work, we detected different regimes of crystallization and compared them by both isothermal dynamic rheometry and nonisothermal differential scanning calorimetry (DSC), which has not been simultaneously addressed yet. A novel analysis, somehow different from the common ones, is used to convert the storage modulus data to crystallinity values leading to more reasonable Avrami parameters in isothermal crystallization. It was found based on isothermal rheokinetic studies that increase of NC content and shear rate are responsible for erratic behavior of Avrami exponent and crystallization rates. Optimistically, however, isothermal crystallization by rheometer was confirmed by DSC. Nonisothermal calorimetric evaluations suggested an accelerated crystallization of PA6 upon increasing NC content and cooling rate. The crystallization behavior was quantified applying Ozawa (r² between 0.070 and 0.975), and combinatorial Avrami–Ozawa (r² between 0.984 and 0.998) models, where the latter appeared more appropriate for demonstration of nonisothermal crystallization of PA6/NC nanocomposites. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46364.     

Synthesis of High‐Performance Pebax®‐1074/DD3R Mixed‐Matrix Membranes for CO2/CH4 Separation

This work deals with the incorporation of deca‐dodecasil 3 rhombohedral (DD3R) zeolite as an inorganic filler into the Pebax®‐1074‐based polymer matrix to enhance the performance of the pure polymeric membrane in CO₂/CH₄ separation. The membranes were fabricated with different concentrations of DD3R. Separation performances of the membranes were investigated at various feed pressures and temperatures. Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and differential scanning calorimetry (DSC) analysis of the prepared membranes were performed. In the best case, selectivity for CO₂/CH₄ separation was improved, while the permeability decreased. Membranes with 1 and 5 wt % DD3R were located in the acceptable region beyond the Robeson plot (1991) for CO₂/CH₄ gas pairs.