Copper-exchanged mordenites as active catalysts for NO selective catalytic reduction by propene under oxidising conditions: Effect of Si/Al ratio, copper content and Brönsted acidity

CuMOR catalysts with different Si/Al ratios and copper contents, prepared from the acid and sodium forms, were studied in NO reduction with propene in the presence of excess oxygen. It was observed that the influence of zeolite Si/Al ratio on CuMOR catalytic activity for NO SCR by propene depends on the catalyst copper content, the reverse being also true. For mordenites prepared from the acid form, it was shown that the most active catalyst must have 60% of copper exchange, whereas for those prepared from the sodium form, the maximum catalytic activity is obtained for catalysts with 20% of copper exchange. Moreover, it was observed that at low copper-exchange levels, the catalyst prepared from the sodium form exhibits much higher activity than those prepared from the acid form. Although, when the copper-exchange level increases, the effect of zeolite form is less pronounced. Thus, it was indicated that Brönsted acidity does not promote the NO selective reduction by propene.     

How much nitrogen is fixed by biological symbiosis in tropical dry forests? 2. Herbs

Although biological nitrogen fixation (BNF) is considered the main input of N in mature and regenerating native tropical vegetation, it has seldom been quantified. Biomass and N accumulation and fixation were determined for spontaneously occurring herbaceous species in caatinga areas in four regeneration stages (2, 17, 39 and >50?years after abandonment from agricultural use). BNF was estimated using the ¹⁵N natural-abundance method. The 2-year regeneration area had the highest total herb (6,355?kg?ha^?1) and legume (262?kg?ha^?1) biomass production, N stocks (82?kg?ha^?1) and fixed N (5.0?kg?ha^?1). N₂-fixing legumes (nine species in the sampled area) contributed over 97?% of legume biomass in all areas. Macroptilium gracile added the largest amount of N (3.9?kg?ha^?1 in the 2-year regeneration area) because of its large biomass production (205?kg?ha^?1), although it was not the species with the highest proportion of fixed N (76?%). All of the N₂-fixing species obtained large proportions of their N from symbiosis, most of them more than 50?%.However, the amounts of fixed N per unit area were relatively low (0.22?C5.00?kg?ha^?1) because the biomass of N₂-fixing species was always less than 5?% of the total herb biomass.     

Recovery of vinyl chloride from by-streams of polyvinyl chloride production by TPSA in a multitubular adsorber

This work aims at developing an efficient and feasible adsorption-based separation process for the separation of vinyl chloride and nitrogen, on activated carbon, by employing a multitubular packed bed geometry, with adsorbent material inside the tubes. Using this geometry, a 2-dimensional mathematical model of a temperature pressure swing adsorption process was used to developed a 6-step three multitubular adsorbers system capable of separating and purifying an industrial scale gas stream of a 40:60% (v/v) vinyl chloride/nitrogen mixture into a 95% (v/v) vinyl chloride stream and a nitrogen stream with a vinyl chloride limit concentration of 8 ppm (w/w). The process reported energy consumption of 4.88 × 10⁶ J/kg_VCM and recovery capacity of 24.35 kg_VCM/(m³_unit h). The multitubular geometry enabled the use of lower adsorbent loads, shorter cycle times, and lower regeneration temperatures. An equivalent 1-dimensional model has also shown to satisfactorily estimate the performance of the current equipment.     

Preparation,thermal and mechanical properties of poly (ether-imide) composite reinforced with carbon nanotube buckypaper

Vacuum filtration technique was employed in order to prepare multiwalled carbon nanotube buckypapers (MWCNT-BP) through a well-dispersed suspension of MWCNT/H₂O with the aid of Triton X-100 surfactant. The obtained BP (buckypaper) was then infiltrated with a solution of poly (ether-imide) (PEI) under vacuum conditions. The visual inspection demonstrated the importance of the centrifugation procedure before the vacuum filtration of the suspension, revealing a smooth surface of the as-prepared buckypaper. Thermogravimetric experiments (TGA) and scanning electron microscopy analyses have demonstrated the role of isopropyl alcohol in the removal of Triton X-100 from the nanotube network. SEM observations of the cross-section view of the samples revealed a porous network of the fabricated BP, and an impregnated structure of the PEI/BP composite, suggesting a good interfacial bonding between MWCNT and PEI. Moreover, significant improvements were achieved in mechanical and thermal properties of PEI matrix by the incorporation of BP, as the increase of both the storage modulus (42%) and the T _g (11 °C) for the PEI/BP composite. TGA have shown a significant increase in the onset decomposition temperature of the polymer by the incorporation of the BP. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48330.     

Kinetics of Soybean Oil Hydrolysis on Niobium Catalysts

The catalytic hydrolysis of soybean oil was used as an alternative for the production of monoglycerides (MG) and diglycerides (DG). The reactions were conducted in a stainless-steel tubular reactor in the temperature range of 240–290 °C, on niobium phosphate (NBP) and niobium oxide (NBO) as catalysts. In the hydrolysis reactions at 270 °C, the maximum selectivities of the products of interest were obtained at 22 % MG and 48 % DG for the reaction with NBP, and 7 % MG and 33 % DG with NBO, for 59 % and 36 % of triglyceride conversion in 10 min, respectively. The proposed kinetic model presented a good fit of the theoretical model with the experimental data, showing that the previous hypotheses considered for the mechanism development are suitable for describing the kinetics of soybean oil hydrolysis.     

Esters from castor oil functionalized with aromatic amines as a potential lubricant

Vegetable oils are very promising alternatives to fossil lubricants due to their abundance, low cost, excellent performance, and environmental friendliness. Due to its multifunctional structure, castor oil is an excellent precursor in the synthesis of new biolubricants. However, it showed poor thermal-oxidative stability and a higher pour point. This study used castor oil fatty acids prepared by transesterification (EHRO), epoxidation (TEPO), and oxirane ring opening with the aromatic amines aniline (ANIL) and p-anisidine (ANIS). The chemical structure of these oils was verified by ¹H and ¹³C NMR analysis, and mass spectrometry. Measurements show that the presence of an aromatic amine increases the viscosity resulting in 172 (ANIL) and 199 (ANIS) cSt at 40°C, but reduces viscosity index to 16 and 1, respectively. In addition, the amine groups can scavenge radicals increasing their thermal and oxidative stability. These products do not oxidize copper, and tribological analysis reveals that ANIS has the lowest torque with wear equivalent to commercial mineral lubricant NH-140.     

Study of the polymerization of 1-octadecene with different rnetallocene catalysts

Summary 1-Octadecene (C18) was polymerized by using different metallocene catalysts. The rac-Et(Ind)₂ZrC1₂/MAO (I) and rac-Me₂Si(Ind)₂ZrC1₂/MAO (III) presented the highest activity as compared with ra-Et(2-Me-Ind)₂ZrCl₂/MAO (II) and Ph₂C(Flu)(Cp)ZrC1₂/MAO (IV) catalysts. Catalyst IV produced polymers with highest molecular weights. The microstructure of the polymers was determined by ¹³C-NMR spectroscopy. Catalyst systems I, II and III produced isotactic polymers while catalyst IV produced polymers with mainly syndiotactic structures but with large amount of stereoregular error. Received: 21 June 2002/Revised version: 4 November 2002/ Accepted: 4 November 2002     

Blends composed of poly(N‐isopropylacrylamide) and an ethylene/vinyl alcohol copolymer: Thermal and morphological studies

Blends of poly(N‐isopropylacrylamide) (PNIPAM) and an ethylene/vinyl alcohol copolymer (EVAL) were obtained through casting from dimethyl sulfoxide (DMSO) solutions and phase inversion in 50/50 DMSO/H₂O solutions. The miscibility and morphology of the PNIPAM/EVAL blends were investigated with thermal and morphological analysis. Differential scanning calorimetry indicated that the crystallinity of EVAL decreased with increasing PNIPAM content and that the blends cast from DMSO/H₂O solutions were miscible in the melt state. Measurements of the melting point depression allowed the determination of the interaction energy density (B) and Flory–Huggins interaction parameter (χ₁₂) with the Nishi–Wang equation. The negative B and χ₁₂ values obtained were examined in terms of the specific intermolecular interactions between the polymers. Scanning electron micrographs revealed that blends obtained by the casting method led to dense membranes, whereas the phase‐inversion method rendered typical macroporous membranes. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 501–505, 2004     

Population balance modeling of bubble size distributions in a direct-contact evaporator using a sparger model

The study of bubble size distributions in direct-contact evaporators was addressed both theoretically and experimentally. Recently developed models for calculating bubble coalescence and breakage frequencies in isothermal bubble columns were adapted to the population balance equation using the bubble mass as the internal coordinate which was discretized using an expansion of the number density function by impulse functions. A sparger model was developed based on experimental data for a non-coalescing system and using bubble formation models for isothermal and non-isothermal conditions. Bubble size distributions in a direct-contact evaporator operating in the quasi-steady-state regime for four different gas superficial velocities, including the homogeneous and heterogeneous regimes, together with the sparger model, were used for estimating the three empirical parameters from the population balance model, which were observed to be functions of the gas superficial velocity. In all cases considered, the population balance model fitted the experimental data rather well and the regressed parameters exhibit the physically expected behavior with changes in the gas superficial velocity.