Modeling and optimization of fringe capacitance of nanoscale DGMOS devices

We analyze the impact of gate electrode thickness and gate underlap on the fringe capacitance of nanoscale double-gate MOS (DGMOS) transistors. We propose an analytical fringe capacitance model considering gate underlap and finite source/drain length. A comparison with the simulation results show that the model can accurately estimate the fringe capacitance of the device. We show that an optimum gate underlap can significantly reduce the fringe capacitance resulting in higher performance and lower power consumption. Also, the effects of process variation in gate underlap devices are discussed. Simulation results on a three-stage ring oscillator show that with optimum gate underlap 32% improvement in delay can be achieved.     

System Operational Evaluation of Mine Monitoring Systems

In the testing of mine monitoring systems, a software package was developed for the mine monitoring test facility designed at West Virginia University. The software establishes delay times of sensor input to annunciation for single alarms and multiple simultaneous alarms. The alarm measurement techniques for the test fixture are described, as is the software developed to analyze and graph monitoring system response data. Also included is the analysis capability of the facility, the criteria for evaluating mine monitoring systems, and typical test data from a sample system.     

Effect of gamma irradiation on the optical properties of CR-39 polymer

The UV-Visible absorption spectra of virgin and gamma irradiated (20–800 kGy) CR-39 polymer have been deduced by using Shimadzu Double beam Double Monochromator UV-Visible Spectrophotometer (UV-2550). The existence of the peaks, their shifting and broadening as a result of gamma irradiation has been discussed. Finally the indirect and direct band gap in virgin and gamma irradiated CR-39 has been determined. The values of indirect band gap have been found to be lower than the corresponding values of direct band gap.     

Atomistic simulations of the solubilization of single-walled carbon nanotubes in toluene

Solubilization of the armchair, metallic (10,10) single-walled carbon nanotubes (SWCNTs) in toluene is modeled using molecular dynamics simulations. Inter- and intra-molecular atomic interactions in the SWCNT + toluene system are represented using COMPASS (Condensed-phased Optimized Molecular Potential for Atomistic Simulation Studies), the first ab initio forcefield that enables an accurate and simultaneous prediction of various gas-phase and condensed-phase properties of organic and inorganic materials.The results obtained show that due to a significant drop in the configurational entropy of toluene, the solvation Gibbs free energy for these nanotubes in toluene is small but positive suggesting that a suspension of these nanotubes in toluene is not stable and that the nanotubes would fall out of the solution. This prediction is consistent with experimental observations.     

A Convenient Synthesis of Some Coumarin Derivatives Using SnCl2 · 2H2O as Catalyst

Some substituted coumarins have been synthesized by von-Pechmann condensation using SnCl₂ · 2H₂O (10 mol %) as catalyst in ethanolic medium. The reactions are simple, easy in handling and environmentally benign.     

Recent advances in isotropic conductive adhesives for electronics packaging applications

Isotropic conductive adhesives (ICAs) have recently received a lot of focus and attention from the researchers in electronics industry as a potential substitute to lead-bearing solders. Numerous studies have shown that ICAs possess many advantages over conventional soldering such as environmental friendliness, finer pitch printing, lower temperature processing and more flexible and simpler processing. However, complete replacement of soldering by ICAs is yet not possible owing to several limitations of ICAs which are mainly related to reliability aspects like limited impact resistance, unstable contact resistance, low adhesion and conductivity etc. Continued efforts for last 15 years have resulted in development of ICAs with improved properties. This review article is aimed at providing a better understanding of ICAs, their principles, performance and significant research and development work addressing the technological utility of ICAs.     

Effect of process parameters on impact strength of Al-7% Si alloy castings produced by VAEPC process

The castings produced by the evaporative pattern casting (EPC) process have blow holes. The blow holes in EPC castings are because of the non-escape of the gas produced as a result of burning of polystyrene pattern in the sand mold. To overcome the problem of blow holes, the EPC process is combined with the vacuum (V)- process. The vacuum applied to EPC mold draws the decomposed gases and improves the casting quality produced by the EPC process. The developed hybrid process has been termed as the vacuum assisted evaporative pattern casting (VAEPC) process. The objective of this paper to investigates the effect of process parameters, i.e, degree of vacuum, pouring temperature, grainfineness number, amplitude of vibration and time of vibration on the impact strength of Al-7% Si alloy castings in VAEPC process. In order to evaluate the effect of selected process parameters, the response surface methodology (RSM) is used to formulate a mathematical model which correlates the independent process parameters with the desired impact strength. The central composite rotatable design has been used to conduct the experiments. The results indicate that the impact strength decreases with increases in the grainfineness number and pouring temperature. Whereas, it has an inverse relationship with amplitude of vibration, time of vibration and degree of vacuum. The best value of impact strength (2.34 N/mm²) has been obtained at 400 mm Hg degree of vacuum imposed, 650°C as pouring temperature, 60 as sand grainfineness number, 460 μm as amplitude of vibration, and 70 s as time of vibration.     

Lean philosophy: implementation in a forging company

This research addresses the implementation of lean philosophy in a forging company with a focus on radial forging production flow lines. Here, the prime motive is to evolve and test several strategies to eliminate waste on the shop floor. In this research, a systematic approach is suggested for the implementation of lean principles. This paper describes an application of value stream mapping (VSM). Consequently, the present and future states of value stream maps are constructed to improve the production process by identifying waste and its sources. Furthermore, Taguchi’s method of design of experiments is pursued here to minimize the forging defects produced due to imperfect operating conditions. A noticeable reduction in set-up time and work-in-process (WIP) inventory level is substantiated. Finally, we conclude with a discussion of managerial implications and the future scope of research.