DQ-Ⅳ催化剂在聚丙烯装置上的试生产

DQ-Ⅳ球形催化剂在扬子石油化工股份有限公司塑料厂聚丙烯装置上首次进行工业化试生产，分别试生产了均聚和嵌段共聚2种聚丙烯产品，并与进口催化剂和原国产催化剂生产作了对比。试生产表明，该催化剂活性较其他催化剂略高，并且活性释放平稳，能满足聚丙烯装置生产的需要，为聚丙烯装置催化剂的全面国产化作好了技术储备。     

考察BP公司KG乙烯工厂的体会

介绍了ＥＰ公司ＫＧ乙烯工厂先进的管理经验，提出了搞好企业合理的设想。     

对煤磨MDC89-7袋式除尘器的节能环保改造

0 前言 湖南韶峰水泥集团有限公司规格为φ2.5 m×3.9 m的风扫式煤磨配套的MDC89-7袋式除尘器于1993年投用,经十多年的生产应用,其导流板及风道损坏达80%左右;外壳、主风道因烧袋和腐蚀,严重变形且花板变得很薄;反吹风道变形穿孔,提升阀密封不严,导致清灰时风量流失严重,运行阻力增加,系统产量降低,且系统中含氧量增加,带来安全隐患;除尘效率下降、污染严重,粉尘排放浓度高达1 g/m3;系统能耗高,且维修强度大(每个滤袋重50kg,每次换袋需12人)且费用高.为此,该公司于2004年4月对该煤磨除尘器进行技术改造,取得了明显的效果.     

由双酚A结晶母液的裂解产物合成双酚A反应过程研究

对反应过程所需催化剂种类及其各影响因素进行了考察。研究表明，大孔强酸性离子交换树脂可替代无机酸作为催化剂用于该反应，其中以未经硫基化处理者为佳；原料中水分的存在不利于产物收率和质量，应控制水的质量分数在1％以下。本研究确定的较佳工艺条件为反应温度65℃，停留时间15min、苯酚／对－异丙烯基苯酚摩尔比20，对应的反应收率为98．5％。对双酚A副产物的处理提供了有效方法。     

苯乙烯/丙烯酸丁酯微乳液共聚物链段分布的研究

以苯乙烯/丙烯酸丁酯(St/BA)为共聚单体,进行了微乳液聚合反应,测定了共聚物组成和共聚单体的竞聚率。由竞聚率计算了共聚物分子的链段分布,分析了共聚物分子的微观结构。     

Scaled Jacobian transpose based control for robotic manipulators

This paper presents a scaled Jacobian transpose based control method for robotic manipulators as a modification of a conventional Jacobian transpose based method. The proposed method has several advantages such as it shows faster convergence and better tracking performance than the conventional method, furthermore, it does not have any singularity problem similar to the conventional method. The scaled Jacobian transpose is obtained by collecting each pseudoinverse of the column vector of the Jacobian matrix. The proposed method performs a given task well under singular configurations while minimizing the task error. Finally, a few comparative studies with the conventional method are provided to show the effectiveness of the proposed method through simulations.     

Multidisciplinary design modeling and optimizationfor satellite with maneuver capability

According to the mission of a satellite with maneuver capability, the collaborative optimization (CO) method was introduced for the satellite system design, and the related multidisciplinary design optimization (MDO) model was established. The possessing and needed velocity increments Δv and Δv _{n e e d} were taken as the measurement of maneuvering capability of the studied satellite, which were then combined with total mass of the satellite to form the optimization objective in the systematic level of the MDO problem. The design variables and constraints of the MDO problem dealt with disciplines or subsystems as guidance, navigation and control (GNC), power, and structure, and corresponding engineering analysis models were also built. A program system to solve the MDO problem wasdeveloped by integrating a non-nested CO method, the commercial and user-supplied codes on framework software iSIGHT. The result showed that the satellite performance could be obviously improved, which also indicates MDO technique is feasible and effective for the spacecraft design problem. The modeling and optimization procedure of the work can be referred for further research and engineering design.     

耐候性PP的研制

以聚烯烃弹性体（POE）为增韧材料、DICPK为结晶成核剂、BsSO4为无机填充剂，研制了耐候改性PP专用料。结果表明，当POE用量为5份、DICPK用量为0．3份、BaSO4用量为30份时，所得专用料能够满足耐候改性PP专用料的性能要求。     

一种改进型离散Hopfield学习算法

针对离散Hopfield 神经网络(DHNN) 的权值设计问题, 提出一种改进型学习算法, 并在DHNN动力学分析的基础上设计该学习算法. 利用矩阵分解的方法(MD) 得到正交矩阵, 并采用得到的正交矩阵直接计算DHNN的权值矩阵. 通过该学习算法得到的权值矩阵, 可以很好地存储训练样本的信息, 使测试样本收敛到稳定点. 该学习算法不需要进行分块计算, 减少了计算步骤和计算量, 降低了网络的迭代次数, 从而提高了网络运行速度. 最后, 将该学习算法应用于水质评价, 验证了其有效性和可行性.     

Kinetic and molecular weight control for methyl methacrylate semibatch polymerization. II. Open control

The gel effect will bring a violent increase of conversion for methyl methacrylate (MMA) polymerization in a short time. It will be very dangerous for the reactor, as it causes an increase of molecular weight and broadens the molecular weight distribution. To unify the kinetics, molecular weight, and its distribution, on the basis of the mathematical models for semibatch polymerization of MMA, three controlled objectives that are the heat load distribution index, the change in molecular weight, and molecular weight distribution index are presented. Three materials (monomer, solvent, and chain transfer agent) and their flow rate and feeding mode are analyzed for the open control of kinetics, molecular weight, and its distribution. The optimum flow rate and mode are obtained. The heat load distribution index and molecular weight distribution index are even less than 2.0 and 2.2, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4399–4405, 2006