多孔硅发光二极管的载流子传输特性研究

制备AI／多孔硅／c-Si／Al结构的多孔硅发光二极管，利用其I-V特性关系，以及在不同温度下其I-V特性的变化，结合多孔硅的特殊微结构及性质，分析了多孔硅发光二极管中载流子的产生和传输过程；通过比较其发光猝灭前后I-V特性的变化，解释了发光猝灭的原因。提出了如果在低电场下能够实现大量载流子在限制性Si微粒中复合．是提高多孔硅电致发光效率的一个途径。     

ZL101合金锶变质效果及热处理工艺的改进

对现场生产的ZLl01合金铸件材质进行了全面分析，针对存在的产品成分不准，变质效果不好，力学性能不合格的问题，通过改进合金的锶变质工艺和热处理工艺，改善了合金的组织和性能，达到了对材料的成分、性能的各项要求。     

Plasma Sprayed Hydroxyapatite Coatings with Nano-hydroxyapatite Prepared by Ultrasonic Precipitation Process

Nano-particle hydroxyapatite （ HA ） was prepared with a novel ultrasonic precipitation process and the as-prepared nanopowder was used to produce hydroxyapatite （ HA ） coatings on titanium substrate via plasma spraying. The phase and the microstructare of the coating were characterized by X- ray diffraction （XRD） and scanning electron microscopy （SEM）. Results showed that spherical particles could be prepared by ultrasonic precipitation process; and a corresponding dense HA coating with molten surface and low-porosity cross-section structure was acquired. During the plasma spraying process, new phases of Ca3 （ PO4 ）2 and Ca2 P2O7 were generated. After heat-treating at 800℃ for 1 h, the contents of Ca3 （ PO4 ）2 and Ca2 P2O7 decreased while HA content increased. Tensile adhesion tests showed that the plasma sprayed coating prepared with the spherical nanoparticles exhibited high tensile bond strength.     

东江水库诱发地震探讨

阐述了东江水库基本情况，通过对库区及周围的地质构造特点、诱发地震监测，总结出东江水库地震的活动特征和诱发地震活动趋势。     

Fractal Nature of Crack Growth under Different Temperature

We have studied numerically a simple crack growth model in a two-dimensional triangular lattice of bonds and nodes which incorporates the sudece of a growing crack bond-breaking probability Pi~ exp{(-Vi+Ei)φ(T)}, where Ei is elastic eneny stored in the i-th bond. Different energy temperature factors φ(T) are employed during crack formation and propagation process with a uniform dilation strain case and a shear case and with periodic boundary condition in the horizontal direction. Our results show that the patterns of the cracks generated are fractal structure and the effective fractal dimensionalities decrease with the increase of the temperature factor φ(T)(the absolute temperature T decreasing). In the paper we also discuss the relation between the effective fractal dimension Deff (the radius Rg Of gyration) and the fractal dimensions D (the radius R of circular), and also give their modification values Ω about two kinds of methods in the lattice model     

Viterbi译码器的硬件实现

介绍了一种Vkerbi译码器的硬件实现方法。设计的基于硬判决的Viterbi译码器具有约束长度长（9)、译码深度深（64)的特点。为了兼顾硬件资源与电路性能两个方面，在设计中使用了4个ACS单元，并根据Xilinx Virtex系列FPGA的结构特点．利用FPGA内部的BlockRAM保存汉明距离和幸存路径，提高了译码速度。     

海水介质中高活性镁合金负极的电化学性能

研制了一种新型镁合金负极材料；用电化学方法测定了镁合金负极在人造海水介质中的电化学性能，用浸泡法测定了材料在人造海水介质中的自腐蚀速度，用扫描电子显微镜观察了镁合金腐蚀后的表面形貌，并与AP65合金和纯镁进行了比较。结果表明，新研制的镁合金在人造海水介质中的开路电位增加，自腐蚀速度降低，稳定工作电位提高，电极表面腐蚀均匀，可开发用于高电性能电池的负极材料。     

碳纳米管的制备及研究

介绍了在直流电弧放电法制备富勒烯过程中，从阴电极表面收集到大量的碳纳米管及巴基葱，产生率达到５０％，并用电子显微镜对其进行了观察和初步研究。     

Modeling and control of magnet power supply system with switch-moderipple regulator

This paper presents the dynamic performance analysis and closed-loop design of a new power supply system for a high-current magnet load. This new system introduces a series switch-mode ripple regulator (SMRR) into a phase-controlled rectifier to improve system dynamic response and to reduce the harmonic content in the magnet current. In this paper, the new system control configuration is explained. The small signal dynamic model is established. The function of the SMRR as a speed-up feed-forward path during dynamic transients is assessed. The criteria of the closed-loop regulator design are identified. The theoretical analyses are accompanied by computer simulation and experimental results. The systematical design procedure is outlined by an example which offers better performance than ever reported on high-current magnet power supplies in terms of fast dynamic response (closed-loop bandwidth several kHz) and low harmonic content (less than 10 ppm) in the magnet current     

峒室爆破CAD设计方法研究

本文对峒室爆破断面布药计算机辅助设计参数驱动方法进行了探讨围绕断面布药主要参数的变化，提出一种基于参数驱动的计算机辅助设计方法，利用ｗｉｎｄｏｗｓ操作系统下的动态数据交换特性，对断面布药进行布药参数优化，实现了交互调整布药，形成一套断面布的计算机软件，为工程爆破设计实现计算机提供了一种可行的方法。