地壳应力场和密度场资料在油气检测中的应用

依据卫星轨道摄动测量结果反演的地壳区域构造应力场和密度场资料，可圈定油气区域构造圈闭和储集油气的低密度层。计算绘制了闽江口扇形洲区域构造应力场和密度卫星遥感图，图上显示出东海近海闽浙中拗陷含油气带与温东丽水油气构造带相接，敖江口官岭与闽江口川石储岛沥青苗等迹象都在此范围内，在闽江口扇形洲东部沿海沙泥沉积区，邻区东海宽长带深厚海沙软泥沉积区及本区北部罗源湾，用大地电磁CSAMT检测到1000－3000m深度范围内的低阻率地层，与本区卫星遥感图图低密度场相符。     

国内外乙丙橡胶市场供需状况

介绍了国内外乙丙橡胶市场的供需状况，并对我国乙丙橡胶的产业发展提出了建议。     

高质量ZnO薄膜的退火性质研究

在LP－MOCVD中，我们利用Zn(C2H5)2作Zn源，CO2作氧源，在（0002）蓝宝石衬底上成功制备出皮c轴取向高度一致的ZnO薄膜，并对其进行500℃-800℃四个不同温度的退火。利用XRD、吸收谱、光致发光谱和AFM等手段研究了退火对ZnO晶体质量和光学性质的影响。退火后，（0002）ZnO的XRD衍射峰强度显著增强，c轴晶格常数变小，同时（0002）ZnOX射红衍射峰半高宽不断减小表明晶粒逐渐增大，这与AFM观察结果较一致。由透射谱拟合得到的光学带隙退火后变小，PL谱的带边发射则加强，并出现红移，蓝带发光被有效抑制，表明ZnO薄膜的质量得到提高。     

橡胶卷材挤出连续硫化生产线的结构特色与工作原理

介绍了橡胶防水防腐卷材挤出连续硫化生产线的结构、特点和工作原理;指出在目前国内同类设备中,该生产设备具有先进性,并可替代引进设备。     

大长径比自旋弹箭横向自振特性的有限元计算方法与结果分析

本文研究大长径比自旋弹箭在飞行时横向振动的自振特性。本文将转子动力学应用于弹道学 ,采用有限元法 ,建立自旋弹箭横向振动自振特性方程。同时给出了计算方法。利用该方程和该方法 ,开发了相应的计算程序。通过数值计算 ,可给出细长旋转弹箭飞行时的进动转速和临界转速 ,以及相应的位移和角度振型。利用该程序 ,进行了实例计算和分析。     

An experimental study of carrier heating on channel noise in deep-submicrometer NMOSFETs via body bias

In this paper, RF noise in 0.18-mum NMOSFETs concerning the contribution of carrier heating and hot carrier effect is characterized and analyzed in detail via a novel approach that modulates the channel carrier heating and number of hot carriers using body bias. We confirm qualitatively a negligible role of hot carrier effect on the channel noise in deep-submicrometer MOSFETs. For a device under reverse body bias (V_b), even though the increase in hot carrier population is clearly characterized by dc measurements, the device high-frequency noise is found to be irrelevant to the increase in the channel hot carriers. Experimental results show that the high-frequency noise is slightly reduced with the increase in |V_b|, and can be qualitatively explained by secondary effects such as the suppression of nonequilibrium channel noise and substrate induced noise. The reduction of NF_min and R_n with the increase in |V_b| may provide a possible methodology to finely adjust the device high-frequency noise performance for circuit design     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

Silicon-to-steel bonding using rapid thermal annealing

This paper presents the rapid, low-temperature bonding between silicon and steel using the rapid thermal annealing process. Three different thin-film adhesion layer systems including silver, gold, and nickel were utilized as the intermediate bonding material to assist the eutectic Pb/Sn bonding between silicon and steel. The bonding temperature was set at 220/spl deg/C for 20 s, with a 20-s ramp-up time. Five experiments were conducted to determine the strength of the bond, including static tensile and compressive four-point bend tests, axial extension tests, tensile bending fatigue tests, and corrosion resistance tests. The test results have shown that the gold adhesion layer is the most robust, demonstrating minimal creep during fatigue tests, no delamination during the tensile or compressive four-point bend tests, and acceptable strength during the axial extension tests. Additionally, all adhesion layers have withstood four months of submersion in various high-temperature solutions and lubricants without failure. Simulations of the axial stresses and strains that developed during the four-point bend and axial extension tests were performed and showed that the presence of the silicon die provides a local reinforcement of the bond as observed in the experimental tests.     

棉织物手感值的模糊综合评判研究

利用模糊综合评判数学模型对棉织物的手感值进行了计算与分析，这种方法简单、可靠，与主观评估结果有很好的一致性，为纺织生产的质量判断提供了便利。