Improvement of AlGaInP light emitting diode by sulfide passivation

The brightness of AlGaInP light emitting diodes (LEDs) has been raised by a factor of 1.12 at 20 mA by sulfide passivation. Meanwhile, the sulfide also can decrease leakage current of AlGaInP LEDs at -2 V to nearly one thousandth of that in the as-fabricated device. The possible causes for the brightness increase of AlGaInP LEDs after sulfide treatment including surface roughness, reduction of Fresnel loss, and effective injection of carriers were demonstrated.     

洼60-H26水平井套铣打捞技术

洼60-H26井是一口中曲率水平井,设计井深1 922 m,由于地面条件的限制,设计采用三维井眼轨道。该井水平段在钻至井深1 801 m时,发生卡钻事故。在卡钻事故处理过程中,采用测卡、爆炸松扣技术取出上部钻具后,应用了不同规格的套铣管对被卡钻具进行套铣,采用间歇式套铣方式实现了大斜度井段(45°-90°)的安全套铣,采用短套铣管完成了时水平井段内φ215．0 mm稳定器的套铣,采用φ228．6 mm套铣管成功套铣水平井段被卡LWD仪器,最后通过震击器震击成功解卡。详细介绍了洼60-H26水平井卡钻事故的处理过程,分析了在水平段处理卡钻事故的难点。该井处理卡钻事故的经验,对以后水平井施工中处理井下事故、打捞贵重仪器具有借鉴价值。     

布帮鞋无浆贴合工艺技术

本工艺是对原有工艺的改进，突破了原有布帮鞋不能采用无浆贴合的局限性，对原有工艺中的不足有了很大的改进，提高了生产效率，改善了鞋子外观质量，增加了鞋子的美观性。     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

HDPE／PS／HDPE－g－PS合金的相容性和力学性能研究

用自制接枝共聚物ＧＲ－Ⅰ、ＧＲ－Ⅱ相容剂研究其对ＨＤＰＥ／ＰＳ共混物相容性和力学性能的影响。通过ＳＥＭ、ＤＭＡ、ＤＳＣ和力学性能测试表征，表明在ＨＤＰＥ／ＰＳ共混中加入这些相容剂其相容性和力学性能有一定提高     

小剂量辐射对肿瘤细胞K_（562）及肿瘤病人天然杀伤细胞（NK）活性的影响

已知小剂量辐射可增强机体免疫功能。从对高本底地区的调查发现，该地区居民肿瘤死亡率及某些肿瘤发病率有所降低（１）。ＮＫ细胞能直接杀伤肿瘤细胞，在肿瘤免疫中起着重要的作用。本文观察小剂量辐射对肿瘤病人和正常人外周血淋巴细胞ＮＫ活性的相对效应以及对人红白血病细胞（Ｋ（５６２）细胞）的影响，以期从体外买验来探索较小剂量辐射对肿瘤治疗的影响     

The zinc-rich corner of the Zn-Fe-Ni-Si quaternary system at 450 °C

Following up on recent studies of the Zn-rich corners of the Zn-Fe-Ni and Zn-Fe-Si ternary systems, a 450 °C isothermal section of the Zn-Fe-Ni-Si quaternary phase diagram with the Zn composition being fixed at 93 at.% was determined experimentally using optical microscopy, scanning electron microscopy (SEM) coupled with energy dispersive x-ray spectroscopy (EDS), and x-ray diffractometry (XRD). FeSi was found to be in equilibrium with almost all phases in the section, including the T, ζ, Ni-δ, NiSi₂, and FeSi₂ phases, as well as the liquid phase (L). Silicon solubilities in the T, ζ, and Ni-δ phases were rather limited. However, the solubilities of Fe and Zn in the NiSi₂ phase, at 4.5 at.% and 7.2 at.%, respectively, were appreciable. The existence of the (L+NiSi₂+Ni-δ) three-phase equilibrium state apparently prevents other Ni-Si compounds from entering equilibrium with the liquid at 450 °C. No true quaternary compound was found in the study.     

沸石加氢处理催化剂的制备方法

考察了渣油加氢处理催化剂制备过程中引入一种低硅铝比沸石的情况，它不仅提高催化剂的酸性，而且由于引入的分子筛孔径集中，最终使催化剂具有集中的孔分布，弥补了制备高活性催化剂采用混捏法的不足，制备出来的催化剂性能更优异。     

Fuzzy Learning of Talbot Effect Guides Optimal Mask Design for Proximity Field Nanopatterning Lithography

Processing methods used in photonics and nanotechnology possess many limitations restricting their application areas such as high cost, inability to produce fine details, problems with scalability, and long processing time. Proximity field nanopatterning is a lithography method which surpasses these limitations. By using interference patterns produced by a two-dimensional phase mask, the technique is able to generate a submicron detailed exposure on a millimeter-size slab of light sensitive photopolymer, which is then developed like a photographic plate to reveal three-dimensional interference patterns from the phase mask. While it is possible to use simulations to obtain the interference patterns produced by a phase mask, realizing the mask dimensions necessary for producing a desired interference pattern is analytically challenging due to the intricacies of light interactions involved in producing the final interference pattern. An alternative method is to iteratively optimize the phase mask until the interference patterns obtained converge to the desired pattern. However, depending on the optimization technique used, one either risks a significant probability of failure or requires a prohibitive number of iterations. We argue that an optimization technique that is to take advantage of the physics of the problem using machine learning methods (here fuzzy learning) can lead to competent mask design. This technique is described in this letter.     

Effects of contact shape on biological wet adhesion

Wet adhesion is widely adopted in biological adhesion systems in nature. Wet adhesion is studied in this paper with the focus on the effect of different contact shapes (flat, concave, convex, and ring-like) on the adhesion force. The evolution of the liquid bridge between a fiber tip and substrate during the detaching process shows two transition points. The first transition from the radius-controlled to the contact-angle controlled process is critical to influence the strength and robustness of adhesion. We show that a concave shape is more effective than a flat one, while a convex shape has no advantage. A ring-like contact shape has advantages in a hydrophobic environment and on a rough surface.