Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.     

Special features of the periodic-pulse-train laser radiation confinement in doped gallium arsenide and zinc selenide

Experimental data on the pulsed laser radiation confinement in compensated GaAs and ZnSe with deep impurity levels are reported for the laser wavelength λ=1.55 μm and a pulse repetition frequency of up to 100 kHz. It is demonstrated that an increase in the pulse repetition rate is accompanied by a decrease in the energy confinement threshold and by an increase in the radiation attenuation coefficient. These effects are explained by the accumulation of nonequilibrium charge carriers related to a dependence of the recombination time constant on the concentration of free impurity centers.     

The emerging landscape of bioinformatics software systems

Fusing computing and biology expertise, bioinformatics software provides a powerful tool for organizing and mining the vast amounts of data genetics researchers are accumulating. As life scientists and computational scientists interact to create useful bioinformatics software systems, several themes or lessons recur. We identify seven themes: the nature of biological data; data storage, analysis and retrieval; computational modeling and simulation; biologically meaningful information integration; data mining; image processing and visualization; and closing the loop     

Adaptive motion control using neural network approximations

In this paper, we present a new adaptive technique for tracking control of mechanical systems in the presence of friction and periodic disturbances. Radial Basis Functions (RBFs) are used to compensate for the effects of nonlinearly occurring parameters in the friction and periodic disturbance model. Theoretical analysis, such as stability and transient performance, is provided. Furthermore, the performance of the adaptive RBF controller and its non-adaptive counterpart are compared.     

Mechanisms of Active Fuzzy Expertise

Consideration was given to the decision making procedures based on the fuzzy messages of experts whose preferences on the set of collective decisions can also be fuzzy.     

Effect of misalignment on electrical characteristics of ACF joints for flip chip on flex applications

The effect of misalignment on the electrical properties of anisotropic conductive film (ACF) joints is investigated in this work. It is found that along with the increase of misalignment, the connection resistance of ACF joints increases. When the misalignment in x-direction is less than 5 μm, the increase rate of connection resistance is quite large. Then, along with the severity of misalignment, the increase rate becomes smaller. Finally, when the misalignment is close to 20 μm, the increase rate rises again. The Holm's electric contact theory is used for understanding the connection resistance variation. On the other hand, with the increase of misalignment in x-direction, the insulation resistance between ACF joints decreases. If the misalignment exceeded 10 μm, the decrease is prominent for the Ni particle ACF joints. This phenomenon can be explained by the effect of dielectric damage of the epoxy.Computer programs are also developed to calculate the variation of the probability of open and shorting after misalignment and predicate the maximum misalignment tolerance. The results show that the open and shorting probability increase abruptly after misalignment. On the view of pad parameters, the open probability is mainly related to the pad area, while the pads gap is critical to the shorting probability. Large pads gap (small pad width) can reduce the shorting probability obviously. On the other hand, enlarging the pad area by increasing pad length decreases the open probability significantly. So comparing to square shape pad, rectangle shape pad can reduce the failure probability greatly.     

Structural acrylic adhesives for the sheet steel fabrication industries

Recent developments in rubber-toughened structural acrylic adhesives now offer sheet steel fabricators the opportunity to replace conventional metal fastening techniques such as spot welding with lower cost, durable, more versatile structural adhesive bonding. These developments, in particular much improved ability to bond oily/waxy surfaces common to the motor car industry and improved retention of fracture toughness after exposure to paint stoving temperatures, are discussed in this paper.