Low-voltage wideband compact CMOS variable gain amplifier

A novel low-voltage wideband CMOS variable gain amplifier (VGA) is proposed. Using a 0.13 /spl mu/m CMOS technology, the VGA exhibits a linear-dB controllable gain range of 40 dB with a bandwidth in excess of 130 MHz, while drawing only 50 /spl mu/A from a single 1 V power supply voltage.     

Measurement of the working parameters of an air-post vertical-cavity surface-emitting laser

We present a complete experimental evaluation of the effective parameters necessary to describe the dynamical behavior of an air-post vertical-cavity surface-emitting lasers, on the basis of theoretical equations which are also derived in this paper. The experimental investigation is composed of several steps, including power versus current measurement, noise spectrum analysis, linewidth evaluation. The complete set of parameters derived, in particular the linewidth-enhancement factor and the spontaneous emission factor, is particularly important for accurate comparisons of theoretical models on the laser dynamics with experiments.     

A 300-MHz 25-/spl mu/A/Mb-leakage on-chip SRAM module featuring process-variation immunity and low-leakage-active mode for mobile-phone application processor

An on-chip 1-Mb SRAM suitable for embedding in the application processor used in mobile cellular phones was developed. This SRAM supports three operating modes - high-speed active mode, low-leakage low-speed active mode, and standby mode - and uses a subdivisional power-line control (SPC) scheme. The combination of three operating modes and the SPC scheme realizes low-power operation under actual usage conditions. It operates at 300 MHz, with leakage of 25 /spl mu/A/Mb in standby mode, and 50 /spl mu/A/Mb at the low-leakage active mode. This SRAM also uses a self-bias write scheme that decreases of minimum operating voltage by about 100 mV.     

Effect of temperature and cyclic heating on the structure and strength of glass textolite

The article established the regularities of change of the physicomechanical characteristics and strength of glass textolites in single and repeated thermal loading. It shows that under multiple loading the intense loss of strength of the investigated materials is due to increased porosity on account of the large number of microcracks appearing in the structure. A correlation is obtained between the elastic and strength characteristics and porosity in dependence on the temperature of multiple heating which in the first approximation is described by a polynomial of second degree with respect to temperature, multiplied by the reciprocal of porosity.Translated from Problemy Prochnosti, No. 6, pp. 53–58, June, 1991.     

Comfort limits for asymmetric thermal radiation

Groups of 32 and 16 subjects of both sexes were exposed in an environmental chamber to radiant asymmetry caused by a cool wall, a warm wall, and a cool ceiling. Each subject was tested individually while seated and clothed at 0.6 clo. During each 3.5-hour experiment the subject was exposed to six radiant temperature asymmetries. He was asked whether and where he experienced any local cool or warm sensation, and whether it was felt to be uncomfortable. During the entire experiment he was kept thermally neutral by changing the air temperature according to his wishes.For cool walls, warm walls, and cool ceilings curves have been established showing the percentage of dissatisfied subjects as a function of the radiant asymmetry. Radiant asymmetry at a warm wall caused less discomfort than a cool wall. A cool ceiling caused less discomfort than a warm ceiling. Accepting that 5% of the subjects may feel uncomfortable. a radiant temperature asymmetry of 10°C is allowable at a cool wall, 23°C at a warm wall, and 14°C under a cool ceiling. A previous study showed that 4°C is allowable under a warm ceiling. Radiant asymmetry had no significant impact on the operative temperatures preferred by the subjects. No significant differences were observed between the responses of men and women exposed to radiant asymmetry.     

Whisker reinforcement of glass-ceramics

Silicon carbide whisker reinforcement of anorthite and cordierite glass ceramics has been studied. At 25 vol% whisker loading the flexural strengths increased from 65–103 MPa to 380–410 MPa, the fracture toughnesses increased from 1.0–1.5 MPa m^1/2 to 5.2–5.5 MPa m^1/2. The strengths decline to 240–276 MPa at 1200 °C. The reasons for the decrease in strength with temperature are discussed. Whiskers from two different sources with differences in diameters and aspect ratios were evaluated and the effect of the whisker morphology on the composite properties was studied. It was found that larger diameter, higher aspect ratio whiskers result in improved composite performance. The composites were also characterized in terms of their thermal properties, i.e. thermal expansions and thermal conductivities. The thermal expansion coefficient from 25–1000 °C for anorthite-based composite was 4.6×10^–6 °C^–1 and that for the cordierite-based composite was 3.62×10^–6 °C^–1. The thermal conductivities at 1000 °C were 3.75 and 4.1 Wm^–1 K^–1 for cordierite and anorthite composites, respectively.     

Minimum-energy multicast in mobile ad hoc networks using network coding

The minimum energy required to transmit one bit of information through a network characterizes the most economical way to communicate in a network. In this paper, we show that, under a layered model of wireless networks, the minimum energy-per-bit for multicasting in a mobile ad hoc network can be found by a linear program; the minimum energy-per-bit can be attained by performing network coding. Compared with conventional routing solutions, network coding not only allows a potentially lower energy-per-bit to be achieved, but also enables the optimal solution to be found in polynomial time, in sharp contrast with the NP-hardness of constructing the minimum-energy multicast tree as the optimal routing solution. We further show that the minimum energy multicast formulation is equivalent to a cost minimization with linear edge-based pricing, where the edge prices are the energy-per-bits of the corresponding physical broadcast links. This paper also investigates minimum energy multicasting with routing. Due to the linearity of the pricing scheme, the minimum energy-per-bit for routing is achievable by using a single distribution tree. A characterization of the admissible rate region for routing with a single tree is presented. The minimum energy-per-bit for multicasting with routing is found by an integer linear program. We show that the relaxation of this integer linear program, studied earlier in the Steiner tree literature, can now be interpreted as the optimization for minimum energy multicasting with network coding. In short, this paper presents a unifying study of minimum energy multicasting with network coding and routing.     

Processes of the Collision Interaction between Ceramic Particles Being Crushed in a Circulation Pneumatic Crusher

A new circulation pneumatic crusher capable of producing submicron powders of refractory materials is presented. A mathematical model is constructed for the dynamic breaking of ceramic macroparticles. This model allows the basic laws of shock-wave crushing in the circulation pneumatic apparatus to be analyzed.__________Translated from Teoreticheskie Osnovy Khimicheskoi Tekhnologii, Vol. 39, No. 3, 2005, pp. 327–333.Original Russian Text Copyright © 2005 by Belov, Biryukov, Roslyak, Yugov, Afanas’ev.     

Preparation and Characterization of Novel Polyimides from 2,6-bis[1-(p-dimethylaminophenylimino)ethyl] pyridine for the Selective Extraction of some Metals

Summary A group of new polyimides has been prepared by solution condensation of 2,6-bis[1-(p-dimethylaminophenylimino)ethyl] pyridine containing pendant NMe₂ units and various dianhyrides in N-methylpyrrolidone (NMP). The tridentate (N-N′-N) pydim ligands were prepared by Schiff-base condensation of 2,6-diacetylpyridine and 4-dimethylaminoaniline in the presence of formic acid as catalyst. These polymers were investigated for their extraction capabilities for Zn(II), Mn(II), Cu(II), Cd (II) and Ni(II) and at different pH. Under different conditions enhanced selectivity was observed. Up to 98% quantitative recoveries were observed for all metals.