Performance of unitary heat pumps: review of ASHRAE Symposium session

1. 1. System design optimization and validation for single-speed heat pump by S.K. Fischer and C.K. Rice, Oak Ridge National Laboratories.

2. 2. Analysis of on/off cycling for an air-to-air heat pump operating in the heating mode by W.A. Miller, Oak Ridge National Laboratories.

3. 3. Field measured cycling, frosting and defrosting losses for a high efficiency air source heat pump by V.D. Baxter and J.C. Moyers, Oak Ridge National Laboratories.

4. 4. Design and available energy analysis of a heating-only residential heat pump for the Western Pacific Northwest by D.E. Elger, C.M. Reistad and S. Lang, Oregon State University.

5. 5. A study of heat pump service life by Nance C. Lovvorn, Alabama Power Company and Carl C. Hiller, Electric Power Research.

Hot-carrier reliability of 20V MOS transistors in 0.13 μm CMOS technology

This paper presents results of reliability investigation of 20 V N-Drift MOS transistor in 0.13 μm CMOS technology. Due to high performances required for CMOS applications, adding high voltage devices becomes a big challenge to guarantee the reliability criteria. In this context, new reliability approaches are needed. Safe Operating Area are defined for switch, V_ds limited and V_gs limited applications in order to improve circuit designs. For V_ds limited applications, deep doping dose effects in drift area are investigated in correlation to lifetime evaluations based on device parameter shifts under hot carrier stressing. To further determine the amount and locations of hot carriers injections, accurate 2D technological and electrical simulations are performed and permit to select the best compromise between performance and reliability for N-Drift MOS transistor.     

Autoscan: a scan design without external scan inputs or outputs

We propose a design-for-testability technique for synchronous sequential circuits called autoscan. Autoscan uses scan chains similar to conventional scan. However, it gives up the external scan inputs and outputs in order to eliminate the test data volume associated with them. Scan operations under autoscan improve the circuit testability by allowing the circuit state to be modified through shifting. Due to the removal of the scan inputs and outputs, synthesis of scan chains under autoscan does not have to satisfy all the constraints imposed on conventional scan chains. We describe a synthesis procedure for autoscan chains, and demonstrate that autoscan allows us to detect almost all the faults that are detectable using conventional scan. We use random sequences in order to show that sequential test generation is not necessary under autoscan. We also describe a test generation procedure, and discuss the effect of autoscan on fault diagnosis.     

Modelling biological processes under anaerobic conditions through integrating titrimetric and off-gas measurements-applied to EBPR systems.

An innovative method for modelling biological processes under anaerobic conditions is presented and discussed. The method is based on titrimetric and off-gas measurements. Titrimetric data is recorded as the addition rate of hydroxyl ions or protons that is required to maintain pH in a bioreactor at a constant level. An off-gas analysis arrangement measures, among other things, the transfer rate of carbon dioxide. The integration of these signals results in a continuous signal which is solely related to the biological reactions. When coupled with a mathematical model of the biological reactions, the signal allows a detailed characterisation of these reactions, which would otherwise be difficult to achieve. Two applications of the method to the enhanced biological phosphorus removal processes are presented and discussed to demonstrate the principle and effectiveness of the method.     

Results of testing a centrifugal bubble singlet-oxygen generator

The results of parametric tests of a centrifugal bubble singlet-oxygen generator based on the reaction of chlorine with an alkaline hydrogen peroxide solution have been given. The utilization of chlorine grows with bubble-layer height, whereas the relative content of O₂(¹Δ) remains constant. Growth in centrifugal acceleration leads to a more efficient utilization of chlorine. A specific oxygen output of more than 1 mmole·cm⁻²·sec⁻¹ from the bubble layer for a degree of chlorine utilization of ∼95% and a singlet-oxygen yield of more than 50% has been attained. It has been shown that a centrifugal bubble singlet-oxygen generator is an efficient energy source for an oxygen-iodine laser. __________ Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 80, No. 3, pp. 121–128, May–June, 2007.     

Fast numerically stable computation of orthogonal Fourier?Mellin moments

An efficient algorithm for the computation of the orthogonal Fourier-Mellin moments (OFMMs) is presented. The proposed method computes the fractional parts of the orthogonal polynomials, which consist of fractional terms, recursively, by eliminating the number of factorial calculations. The recursive computation of the fractional terms makes the overall computation of the OFMMs a very fast procedure in comparison with the conventional direct method. Actually, the computational complexity of the proposed method is linear O(p) in multiplications, with p being the moment order, while the corresponding complexity of the direct method is O(p²). Moreover, this recursive algorithm has better numerical behaviour, as it arrives at an overflow situation much later than the original one and does not introduce any finite precision errors. These are the two major advantages of the algorithm introduced in the current work, establishing the computation of the OFMMs to a very high order as a quite easy and achievable task. Appropriate simulations on images of different sizes justify the superiority of the proposed algorithm over the conventional algorithm currently used     

Reduction of optical beat interference using gain-saturated RSOA in upstream WDM/SCM optical links

A new scheme for reducing optical beat interference (OBI) noise in optical network units is proposed for subcarrier multiplexing-based access network applications. The optical spectrum of the transmit lasers is broadened by using a radio frequency (RF) clipping tone with a modulation depth greater than one. This reduces the impact of the OBI noise. The distortions caused by an RF clipping tone are also suppressed by introducing a gain-saturated reflective optical amplifier, which shows the characteristics of high-pass filter. The proposed scheme has been verified by measuring the error vector magnitude of 16QAM signal with 20 Mbps. Error-free transmission has been achieved even when the light of OBI-noise-causing lasers is stronger than that of the signal laser by 7 dB     

Singular Trajectories in Multi-Input Time-Optimal Problems: Application to Controlled Mechanical Systems

This paper deals with the time-optimal control problem for a class of control systems which includes controlled mechanical systems with possible dissipation terms. The Lie algebras associated with such mechanical systems have certain special properties. These properties are explored and used in conjunction with the Pontryagin maximum principle to determine the structure of singular extremals and, in particular, time-optimal trajectories. The theory is illustrated by an application to a time-optimal problem for a class of underwater vehicles.