An electrical network approach to the analysis of semiconductordevices

A simple electrical network is used to represent the five differential equations describing basic phenomena in one-dimensional semiconductor devices. Both standard and integrated approaches for solving transport equations are developed. Also, an electrical network equivalent for the nonlinear Poisson equation was derived. It allows students to better understand the physical phenomena and the process of computer simulation of such semiconductor devices     

On the geometry of parallel impedances

A geometrical construction for the equivalent (sinusoidal) impedance of two impedances connected in parallel is presented. The special case of two resistors connected in parallel is reviewed     

Work-site smoking policies: their population impact in Washington State

This article presents data from a population-based, random-digit dialing telephone survey of 1228 employed adults in Washington State, conducted 1989 through 1990. Eighty-one percent of men and 91% of women reported work-site smoking restrictions. Employees in work sites with no-smoking policies were less likely to be current smokers; men in work sites with policies restricting smoking smoked fewer cigarettes on both workdays and nonworkdays. Forty-eight percent of male and 53% of female smokers reported reduced smoking as a result of work-site policy. Work-site smoking policies, intended to protect against smoke exposure, may also reduce employee smoking.     

A 56 mm twin aperture model dipole magnet for the large hadroncollider

A 56 mm twin aperture model dipole magnet for the large hadron collider has been built at CERN. The magnet design incorporates stainless steel collars and a special yoke structure to minimize saturation-induced field errors. The magnet has proved to be the most successful model prototype constructed so far. In the tests the design field of 10.0 Tesla was achieved with a record-short training. In this paper, the quench performance and the electromagnetic behavior of the magnet are presented and discussed     

Heading towards an advanced signalling system for multimedia,multiparty services in broadband ISDN

Introduction of the broadband integrated services digital network (B-ISDN) will enable network users to make use of advanced multimedia, multiparty services. With this aim in view, RACE II project R2044, MAGIC, is investigating long-term signalling requirements, architecture and protocols for B-ISDN. New service concepts are being developed in MAGIC which will provide more flexibility when compared to narrowband ISDN (N-ISDN). The service requirements and other signalling requirements, such as the separation between call and associated connections at the network-node interface, are used to determine the distribution of functions over the network. The signalling protocols which are used to exchange the signalling information are subsequently developed. These signalling protocols are simulated to prove the performance and the feasibility of call handling concepts     

All-optical wavelength conversion by semiconductor opticalamplifiers

Following a brief introduction to the applications for wavelength conversion and the different available conversion techniques, the paper gives an in depth analysis of cross gain and cross phase wavelength conversion in semiconductor optical amplifiers. The influence of saturation filtering on the bandwidth of the converters is explained and conditions for conversion at 20 Gb/s or more are identified. The cross gain modulation scheme shows extinction ratio degradation for conversion to longer wavelengths. This can be overcome using cross phase modulation in semiconductor optical amplifiers that are integrated into interferometric structures. The first results for monolithic integrated interferometric wavelength converters are reviewed, and the quality of the converted signals is demonstrated by transmission of 10 Gb/s converted signals over 60 km of nondispersion shifted single mode fiber     

Direct finite element design optimisation of the cagelessreluctance synchronous machine

The finite element analysis method is used directly in optimisation algorithms to optimise in multidimensions the design of the cageless reluctance synchronous machine. Two optimisation methods are evaluated to minimise or maximise the function value. These are the direction set method of Powell and the quasi-Newton algorithm. Both methods proved to be successful, with some advantages and disadvantages. Using these methods at a power level below 10 kW, results are given of structures of the reluctance synchronous machine which have been optimised according to specific criteria. Calculated and measured results show that the maximum torque optimum designed reluctance synchronous machine has the advantages of high power density and high efficiency     

Designing for parallel fuzzy computing

As the number of fuzzy logic applications increases, demand for faster architectures will grow. Our design for a VLSI fuzzy processor uses fuzzy inference techniques that optimize processing time. Preprocessing that reduces the number of rules to be processed, parallel computation of active rule degrees of activation, and scalability are major features of this architecture. The journal issue contains a concise summary of this article. The complete article is linked to Micro's home page on the World Wide Web (http://www.computer.org/pubs/micro/micro.htm)