Value analysis of intermittent generation sources from the systemoperations perspective

The objective of this study is to determine the economic and operational impact on energy cost of incorporating large photovoltaic (PV) and wind energy conversion systems (WECS) into the electric utility generation mix. In most cases, PV and WECS power outputs are subtracted from the utility load with the expectation that conventional generation would meet the residual load. This approach is valid for small penetration levels and/or for PV and WECS facilities connected near load centers, However, several constraints such as thermal generation characteristics, fuel supply and delivery, spinning reserve requirements, and hydro availability are not adequately represented in this process. To determine the optimal value of large-scale PV and WECS applications, a new methodology that would take into account the aforementioned constraints as well as a more global penetration is developed. Results indicate that while high hydro availability increases PV penetration levels, high ramping rates can also significantly increase penetration levels     

Mean residence time of gas in mechanically agitated gas–liquid contactors

In the present study of gas–liquid contactors, mean residence/contact time was calculated from knowledge of superficial velocity and the gas phase hold-up, for various gas rates and impeller geometry and speeds, and compared with values obtained from RTD measurements. A new correlation, involving Flow Number, Froude Number, system geometry and the physical properties, is proposed. This uses the authors data and those available in literature.     

Experimental estimate of self-irradiation of building bricks due to incorporated radionuclides

A method is described for experimentally determining the dose rate created in building bricks by incorporated natural radionuclides. It was established using the thermoluminescence dosimetry method that the measured dose rate depends on the detector thickness, the mass of the ceramic product investigated, and the irradiation geometry. The contributions to the measured dose of weakly penetrating α and β radiation and hard ψ radiation are separated, the ratio between them depending on the experimental conditions. Translated from Izmeritel'naya Tekhnika, No. 7, pp. 62–66, July, 1996.     

The morphological stability of lateral growth in solid-solid phase transformation during thin-film interdiffusion in Al/Cu bimetal films

This article describes the phenomenon of morphological instability in solid-solid phase transformations during thin-film interdiffusion, specifically related to the initial stages of precipitation when phase growth occurs along the interface between thin films. The experimental observations that revealed this effect will be presented, and a working hypothesis will be discussed. Experimental observations suggest that the ledge mechanism of growth is present in this system but does not inhibit the formation of interfacial instabilities. It is proposed that morphological stability for solid-phase growth occurring during thin-film interdiffusion can be treated by the inclusion of a solute-source term into the two-dimensional perturbation approach generally used to study unstable growth morphologies. Experimental observations that provide qualitative and semiquantitative support for the solute-source model are also presented.     

Perinatal problems and the prevention of premature labor]

The article describes the experience of implementing patient-focused care from a physician's perspective. Pitfalls that guarantee failure are presented, many of which are avoidable with early participation by all parties involved: administrators, nursing staff, physicians, and patients. Contamination of the process with downsizing needs, lack of support for staff in dealing with necessary change, loss of administrative commitment, and withholding of appropriated funds are among the key errors to be avoided.     

Design and performance evaluation of a banyan network basedinterconnection structure for ATM switches

This paper presents a new self-routing packet network called the plane interconnected parallel network (PIPN). In the proposed design, the traffic arriving at the network is shaped and routed through two banyan network based interconnected planes. The interconnections between the planes distribute the incoming load more homogeneously over the network. The throughput of the network under uniform and heterogeneous traffic requirements is studied analytically and by simulation. The results are compared with the results of the baseline network and another banyan network based parallel interconnection network. It is shown that, for the proposed design, a higher degree of heterogeneity results in better performance     

Finite element beam propagation method for three-dimensionaloptical waveguide structures

A beam propagation method (BPM) based on the finite element method (FEM) is described for longitudinally varying three-dimensional (3-D) optical waveguides. In order to avoid nonphysical reflections from the computational window edges, the transparent boundary condition is introduced. The present algorithm using the Pade approximation is, to our knowledge, the first wide-angle finite element beam propagation method for 3-D waveguide structures. To show the validity and usefulness of this approach, numerical results are shown for Gaussian-beam excitation of a straight rib waveguide and guided-mode propagation in a Y-branching rib waveguide     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

Digitally tunable optical filters using arrayed-waveguide grating(AWG) multiplexers and optical switches

Two novel configurations for digitally tunable optical filters based on arrayed-waveguide grating (AWG) multiplexers are described in detail with emphasis on the connection of the AWG multiplexer and optical switches. Performance comparisons show that conventional configurations are disadvantaged by the switch size required and loss imbalance among the optical frequency-division-multiplexed (FDM) channels; the proposed configurations require only O(√(N)) switch elements to select one of N FDM channels, and the loss imbalance is lower by up to 75% in decibel