The colored revolution of bioimaging

This paper provides an overview of the main aspects of modern fluorescence microscopy. It covers the principles of fluorescence and highlights the key discoveries in the history of fluorescence microscopy. The paper also discusses the optics of fluorescence microscopes and examines the various types of detectors. It also discusses the signal and image processing challenges in fluorescence microscopy and highlights some of the present developments and future trends in the field.     

Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Scale Up from Small Oven-Drying Tests of Mineral Concentrate to Pilot-Scale Drying with a Heated Pad

While Fickian diffusion models are commonly used in other applications, there are few reports of them being applied to the batch drying of a mineral concentrate. Diffusion coefficients estimated from small-scale oven-drying tests were used to predict the drying behavior of a concentrate sample 1 m × 1 m in area and 50 cm deep, with a heated bottom pad. These pilot-scale tests included both daily turning of the sample and turning every three days. The excellent quantitative agreement between the predicted and observed pilot-scale behavior gives a high level of confidence in the model predictions and suggests that a Fickian diffusion model is adequate to predict the behavior of mineral concentrates at the low moisture contents used here.     

Mixed oxide supported hydrodesulfurization catalysts—a review

Support effects form important aspect of hydrodesulfurization (HDS) studies and mixed oxide supports received maximum attention in the last two decades. This review will focus attention on studies on mixed oxide supported Mo and W catalysts. For convenience of discussion, these are divided into Al₂O₃ containing mixed oxide supports, TiO₂ containing mixed oxide supports, ZrO₂ containing mixed oxide supports and other mixed oxide supports containing all the rest. TiO₂ containing mixed oxides received maximum attention, especially TiO₂–Al₂O₃ supported catalysts. A brief discussion about their prospects for application to ultradeep desulfurization is also included. An overview of the available literature with emphasis on research carried out in our laboratory form the contents of this publication.     

Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

Mathematical Modeling of Thermomechanical Processes under Intense Thermal Effect

Mathematical models of thermomechanical processes which are based on the laws of rational thermodynamics of irreversible processes are treated. Singular features of the unsteady-state behavior of a continuous medium are demonstrated within different models, such as a medium with internal parameters of state, a medium with memory, and a medium of the velocity type.     

Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

Near-field corrections to site attenuation

The theoretical model used for calculating normalized site attenuation for broadband antennas in ANSI C63.4-1992 and for antenna calibration in ANSI C63.5-1988 includes only the radiation terms in the electric field. The omission of the near field terms leads to errors of as much as 2.0 dB at 30 MHz for horizontally polarized antennas separated by 3 m. Corrected values of normalized site attenuation and E _D^max are presented for the 30-300 MHz frequency range     

A base-band NDS electrode configuration for HACT devices

Heterostructure Acoustic Charge Transport (HACT) devices have been fabricated with a new nondestructive sense (NDS) electrode structure that provides for the recovery of base-band signals without the use of an integrating capacitor. This electrode structure provides an output signal comprising an RF carrier at the SAW frequency, amplitude modulated by the sampled input signal which has been delayed by a period proportional to the output electrodes distance from the input diode. The output of the NDS electrode structure is subsequently demodulated to provide the base-band signal