端羟基聚乳酸微球的制备与降解

以1,4-丁二醇和D,L-乳酸为原料,经缩合聚合法制备了端羟基聚乳酸,并用溶剂挥发法制备了端羟基聚乳酸微球.考察了乳化剂浓度、油水相比例及聚乳酸浓度对微球平均粒径和形貌的影响,并在pH=7.4缓冲溶液中进行了微球的降解.结果表明以二氯甲烷为溶剂,PVA作为乳化剂,室温和600r/min搅拌速度下可制得平均粒径0.5-1.0m的较均匀的、表面平滑的端羟基聚乳酸微球.随着在pH=7.4下降解时间增加,微球表面变得粗糙.     

“香山81号院”（半山枫林二期）外环境设计

1“居山”与”隐贵山居“ 回想一下人类的聚居行为颇为有趣，当年我们的祖先拼命从险山恶水的自然环境中挣脱出来，为的是得到更加安全和便利的聚居条件，但似乎从那一刻起本能式的回归意识便时刻魂牵梦绕，隐隐作响。其实无论是脱离自然还是回归自然，对于现实而言两者皆是虚幻和理想的。     

En/Decoder for Spectral Phase-Coded OCDMA System Based on Amplitude Sampled FBG

A novel en/decoder for spectral phase-coded optical code-division multiple-access system based on amplitude sampled fiber Bragg grating (FBG) is proposed. Both equivalent chirp and equivalent phase shift are achieved by amplitude sampling. Compared with previous en/decoder based on step chirped FBG, it is easier to fabricate. The performance of the proposed en/decoder is verified by both numerical simulation and experimental demonstration.     

Epoxidation of high trans‐1,4‐polyisoprene and its properties

A new organic‐solvent‐free water‐phase suspension method was used to synthesize partially epoxidized high trans‐1,4‐polyisoprene (TPI) to improve its properties, including oil resistance and wet‐skid resistance. The epoxidation was conducted in an aqueous peracetic acid solution and on the TPI granules prepared by a bulk precipitation method with supported titanium catalyst. The effects of the synthesis conditions, including reaction temperature, reaction time, and pH value, on the epoxy content were investigated. Epoxidized trans‐1,4‐polyisoprene (ETPI) with epoxy contents between 10 and 80% were obtained within 4 h. Both the amorphous and crystalline regions of TPI were epoxidized. The crystallization properties decreased with increasing epoxy content. ETPIs possessed lower mechanical properties than TPI but could be enhanced by vulcanization. The oil resistance and wet‐skid resistance were significantly improved after epoxidation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and adsorption behavior of a cellulose‐based,mixed‐mode adsorbent with a benzylamine ligand for expanded bed applications

A novel mixed‐mode expanded bed adsorbent with anion‐exchange properties was explored with benzylamine as the functional ligand. The cellulose composite matrix, densified with stainless steel powder, was prepared with the method of water‐in‐oil suspension thermal regeneration. High activation levels of the cellulose matrix were obtained with allyl bromide because of the relative inertness of the allyl group under the conditions of the activation reaction. After the formation of the bromohydrin with N‐bromosuccinimide and coupling with benzylamine, the activated matrix was derived to function as a mixed‐mode adsorbent containing both hydrophobic and ionic groups. The protein adsorption capacity was investigated with bovine serum albumin as a model protein. The results indicated that the prepared adsorbent could bind bovine serum albumin with a high adsorption capacity, and it showed salt tolerance. Effective desorption was achieved by a pH adjustment across the isoelectric point of the protein. The interactions between the cell and adsorbent were studied, and the bioadhesion was shielded by the adjustment of the salt concentration above 0.1M. Stable fluidization in the expanded bed was obtained even in a 2% (dry weight) yeast suspension. The direct capture of target proteins from a biomass‐containing feedstock without extra dilution steps could be expected with the mixed‐mode adsorbent prepared in this work, and this would be especially appropriate for expanded bed adsorption applications. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

一种T形高压输电线路故障测距新方法

对T形线路的故障测距，现有方法都是先判断故障支路，再将3端线路等效成2端线路进行测距。但在 T节点附近短路，尤其是经高阻短路时，现有的测距方法由于无法正确判别故障支路而存在一定范围的测距死区。针对上述缺陷，分别假设故障发生在某一支路，由假定正常的2段支路端的电压、电流推算求得 T节点电压和注入假定故障支路的电流，从而分别求得3个故障距离。经证明，求得的3个故障距离有且仅有1个在0和对应支路总长度之间，该距离就是真实的故障距离，故障发生在对应支路上。该方法无需事先判别故障支路即可测距，在 T节点附近经高阻故障时无测距死区。其测距精度理论上不受过渡电阻和故障类型影响，无需故障前数据，且对滤波无高要求。EMTP仿真结果表明该方法正确、有效，测距精度高。     

旋转式伽玛刀的辐射剂量学

旋转式伽玛刀的辐射剂量学指标的物理测试在放射性医疗设备投放医院正式临床使用前是必不可少的，是对设备及其附件的设计、加工制造、安装以及电气控制系统等的全面综合性检定。用电离室作辐射剂量学的绝对测量，用胶片法进行相对测量，给出了测量结果并进行了讨论。     

Study on phase behavior–impact strength relationship of unsaturated polyester/polyurethane hybrid polymer network

The phase behavior of a hybrid polymer network (HPN) composed of poly[(propylene glycol maleate)-co-(propylene glycol phthalate)] crosslinked with styrene and polyester–urethane crosslinked with methylene-bis-ortho-chloroaniline was examined. The correlation between phase separation and impact strength of the HPNs is discussed. The composition of HPNs has an effect on their properties.     

利用热管纺丝技术一步法生产FCY

利用平板型热管纺丝装置对普通高速纺丝机进行技术改造，并一步法生产出充分结晶的ＰＥＴ纤维（ＦＣＹ）。该纤维可直接用于织造，调节热管温度、热管安装位置可获得满足后道工序不同需要的ＦＣＹ。     

Effects of nitric oxide annealing of thermally grown silicondioxide characteristics

The effects of nitric oxide (NO) annealing on conventional thermal oxides are reported in this letter. The oxide thickness increase, resulting from NO annealing, is found to be only a few angstroms (<0.5 nm) and independent on the initial oxide thickness. Furthermore, both the electrical and physical characteristics are improved. This technique is expected to achieve sub-5 nm high quality ultrathin dielectric films for the applications in EEPROM's and ULSI