Dissipative structures of autocatalytic reactions in tubular flow reactors

Dissipative structures of autocatalytic reactions with initially uniform concentrations are studied in tubular flow reactors. A unique steady state exists in a continuous stirred tank reactor. Linear stability analysis predicts either a stable node, a focus or an unstable saddle-focus. Sustained oscillations around the unstable focus can occur for high values of Damköhler number. In distributed parameter systems, travelling, standing or complex oscillatory waves are detected. For low values of Damköhler number, travelling waves with pseudo-constant patterns are observed. With intermediate values of Damköhler number, single or multiple standing waves are obtained. The temporal behavior indicates also the appearance of retriggering or echo waves. For high values of Damköhler number, both single peak and complex multipeak oscillations are found. In the cell model, both regular oscillations near the inlet and chaotic behavior downstream are observed. In the dispersion model, higher Peclet numbers eliminate the oscillations. The spatial profile shows a train of pulsating waves for the discret model and a single pulsating or solitary wave for the continuous model.     

Synthesis and characterization of CdS nanocrystals embedded on solid electrolyte films

In this article nano‐sized CdS crystal embedded in a PEO matrix was successfully prepared by a complex transformation method that is universal for preparing nanosized compounds containing transition metals. The size of embedded CdS particles was in the nanoscale from 2 to 10 nm determined by X‐ray diffusion. The nanosized CdS displayed the expected blue shift of the onset absorbance in the UV spectrum. The amount of blue shift depends upon the dipping time of the PEO–cadmium complex film in a sodium sulfide solution as well as its concentration. The most effective means for adjusting the size of CdS nanocrystals is to change the ratio of the oxygen along with the PEO chain to the cadmium ion in the complex film. The alkali salt in the film would contribute to the conductivity of the composite film. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1263–1268, 2002; DOI 10.1002/app.10459     

Modeling and economic analysis of CO<Subscript>2</Subscript> separation process with hollow fiber membrane modules

The main purpose of the study was to develop a model using ASPEN and Excel simulation method to establish optimum CO₂ separation process utilizing hollow fiber membrane modules to treat exhaust gas from LNG combustion. During the simulation, optimum conditions of each CO₂ separation scenario were determined while operating parameters of CO₂ separation process were varied. The characteristics of hollow fibers membrane were assigned as 60 GPU of permeability and 25 of selectivity for the simulation. The simulation results illustrated that 4 stage connection of membrane module is required in order to achieve over 99% of CO₂ purity and 90% of recovery rate. The resulted optimum design and operation parameters throughout the simulation were also correlated with the experimental data from the actual CO₂ separation facility which has a capacity of 1,000 Nm³/day located in the Korea Research Institute of Chemical Technology. Throughout the simulation, the operating parameters of minimum energy consumption were evaluated. Economic analysis of pilot scale of CO₂ separation plant was done with the comparison of energy cost of CO₂ recovery and equipment cost of the plant based on the simulation model. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Electromechanical behavior of hybrid carbon/glass fiber composites with tension and bending

To understand the smart (i.e., good memory) characteristics of hybrid composites of carbon fibers (CFs) and glass fibers (GFs) with epoxy resin as a matrix, the changes in the electrical resistance of composites with tension and on bending were investigated. The electrical resistance behavior of composites under tension changed with the composition of the CF/GF, as well as with the applied strain. The fractional electrical resistance increased slowly with increasing strain within a relatively low strain region. However, with further loading it increased stepwise with the strain according to the fracture of the CF layers. The strain sensitivity of the samples increased with increasing CF weight percentage, and the samples incorporating more than 40 wt % CF showed a strain sensitivity higher than 1.54 for a single CF. The changes in the fractional electrical resistance with bending were not so dominant as those with tension. This difference was attributed to the action of two cancelling effects, which are the increasing and decreasing fractional electrical resistance due to tension and compression with bending, respectively. On recovery from a large applied bending, the fractional electrical resistance decreased slowly with unloading because of the increase of contacts between the fibers that resulted from the reorganization of ruptured CFs during the recovery. Even the composites incorporating a relatively small CF content showed an irreversible electrical resistance with both tension and bending. However, the strain sensitivity being larger with tension than with bending is ascribed to the difference in their mechanical behaviors. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2447–2453, 2002     

Infrared reflectance and transmission spectra of semiconducting non-stoichiometric CdGe x As2

The infrared reflectance and transmission spectra of amorphous CdGe _x As₂ were investigated to study the amorphous structure with varying Ge content. The mid-infrared optical absorption edges of amorphous CdGe _x As₂ with 0<x<1.2, were observed in the range 1.6–1.7 m, indicating a structural similarity in short-range order throughout. Comparing the reflectance and transmission spectra of amorphous and devitrified crystalline phases established that the structures of amorphous CdGe _x As₂ transformed from the CdAs₂ basic structure to the chalcopyrite (CdGeAs₂) structure, as one progressed fromx=0 tox=1.2. The infrared spectra were interpreted interactively with radial distribution function, magnetic susceptibility, density measurements, and crystallization studies. The crystallization behaviour of amorphous CdGe _x As₂ that was heat treated at different temperatures was investigated using far-infrared transmission spectra.     

Winglet geometry effects on tip leakage loss over the plane tip in a turbine cascade

The effects of winglet offset distance, winglet coverage, and winglet cross section on the over-tip leakage loss for the plane tip have been investigated experimentally in a turbine blade cascade for a tip gap height-to-span ratio of h/s = 1.36 %. The results show that the over-tip leakage loss for the full coverage winglet increases steeply with increasing the winglet offset distance. This loss generation is attributed to flow disturbances over the forward-facing and backward-facing steps within the tip gap. The winglet flush mounted to the tip surface provides the best result. With the leading edge winglet portion or without it, the both-side winglet always provides better aerodynamic performance than the corresponding pressure-side winglet or suction-side winglet. Longer coverage of the both-side winglet leads to lower loss. Therefore, the full coverage winglet performs best in the loss reduction for the plane tip. In general, thinner winglet leads to better aerodynamic result, and the winglet cross section having a slant bottom surface with the smallest thickness at its outer end is recommended.     

Comparison of liquid-phase and methanol-swelling crosslinking processes of polyimide dense membrane for CO2/CH4 separation

To overcome the plasticization effect in polyimide membranes, many researchers have proposed crosslinking method. This can reduce an inter-segmental mobility by tightening and rigidifying the polymer chains. However, it is difficult to modify the whole polymer chains throughout the membrane because the reaction can be hindered by the diffusion rate of the crosslinker. In particular, it is hard for bulky crosslinker to penetrate a dense membrane with a small d-spacing. This study investigated the effect of crosslinking a dense Matrimid membrane with p-phenylenediamine (p-PDA) via two different crosslinking methods (i.e., methanol-swelling crosslinking process [M-SCP] and liquid-phase crosslinking process [L-PCP]). Most of the crosslinking reaction in M-SCP occurs on the membrane surface due to difficulty in penetration of the bulky p-PDA into the Matrimid dense membrane. In contrast, the L-PCP allows uniform crosslinking across the membrane. The membranes crosslinked using L-PCP showed excellent chemical resistance. Furthermore, the plasticization phenomenon was not observed in the membranes crosslinked using L-PCP with p-PDA more than 15%. Meanwhile, the membrane crosslinked using M-SCP exhibited poor plasticization and chemical resistance properties. These results showed that the L-PCP method can be more effective for the crosslinking of dense membrane to deliver both high plasticization and chemical resistance.     

AgNO3浓度对SPE电极镀覆纳米Ag的影响

采用浸渍还原法(I-R法)在Nafion离子膜上镀覆纳米Ag,并就AgNO3浓度对SPE电极镀覆纳米银的影响作了研究.研究表明采用I-R法可制得细致Ag镀层,有效增加Ag的分散度及电极的真实面积.在还原剂浓度为0.1mol·L-1,浸渍还原温度均为50℃及浸渍还原时间分别为40 min,60 min的条件下,调节浸渍液AgNO3浓度至3.5 mmol·L-1时,可获得致密、均匀的纳米级Ag/SPE电极.同时验证砂纸糙化的预处理有利于增加Ag的负载和附着力,有利于提高Ag催化层的有效面积.     

数字化点焊控制系统中人机接口的设计

采用自制键盘和液晶显示器（LCD），在数字化点焊控制系统中实现了简便、直观地设置点焊规范参数的人机接口，并给出了详细的软、硬件设计方案，实验结果表明：电路工作可靠，实现了设计目标。