Efficiency increase of an induction motor by improving coolingperformance

Improving the efficiency of induction motors, which are the most energy consuming electric machines in the world, saves much energy. The efficiency can be increased by improving cooling performance as well as by using better materials or by improving electromagnetic performance with better design. This paper presents the relationship between the efficiency or the losses and the temperature of coils with experiments as well as simulations by changing parameters such as the load and the flow rate of cooling air. The losses and the efficiency are calculated from an equivalent circuit method as well as experiments. Coil temperatures variation affects much on the efficiency. The internal cooling method is better than that of external cooling for the coil temperature reduction. Several cooling methods are compared focusing on the fan efficiency and performance, from which the values of the efficiencies of the motors are expected. The fan efficiency as well as the fan performance should be considered for the optimum fan design to increase the total efficiency of a motor. The simulations are validated by the comparison with the experiments     

A compact fiber-optic magnetometer employing an amorphous metalwire transducer

A compact fiber-optic magnetometer constructed using a short piece of amorphous metal wire (5-cm long×100-μm diameter) as the magnetostrictive transducer is discussed. The inherently large ratio of length to cross-sectional area results in a low demagnetization along the axial direction. A magnetostrictive constant of 5×10^-5 /Oe², which is 10-50 times larger than the reported values for transducers made from Metglas ribbons, was measured. Minimum detectable magnetic fields on the order of 10^-5 Oe/Hz^1/2 at 1 Hz were achieved using a 5-cm-long sensing fiber     

Experimental observations on flow characteristics in an open two-phase natural circulation loop

The flow behavior in an open two-phase natural circulation loop was studied experimentally using Freon-113. The heat flux, inlet- and exit-restrictions, liquid charging level and inlet subcooling were taken as parameters. As a result, three basic circulation modes were observed with variation of the heat flux: periodic circulation (A), continuous circulation, and periodic circulation (B). Of these modes, only the continuous circulation mode was stable and the maximum circulation rate appeared with this mode. An increase in the inlet-restriction and/or decrease in the exit-restriction broadened the range of the continuous circulation mode and stabilized the system. When the liquid charging level was lowered or the inlet subcooling was decreased, the continuous circulation mode started at a lower heat flux and the system became stable. The results are summarized on instability maps in the plane of heat flux vs. inlet subcooling.     

Classification and prediction of the critical heat flux using fuzzy theory and artificial neural networks

A new method to predict the critical heat flux (CHF) is proposed, based on the fuzzy clustering and artificial neural network. The fuzzy clustering classifies the experimental CHF data into a few data clusters (data groups) according to the data characteristics. After classification of the experimental data, the characteristics of the resulting clusters are discussed with emphasis on the distribution of the experimental conditions and physical mechanism. The CHF data in each group are trained in an artificial neural network to predict the CHF. The artificial neural network adjusts the weight so as to minimize the prediction error within the corresponding cluster. Application of the proposed method to the KAIST CHF data bank shows good prediction capability of the CHF, better than other existing methods.     

Training sequence design and channel estimation of OFDM-CDMA broadband wireless access networks with diversity techniques

In this paper, an OFDM-CDMA system employing various diversity schemes is considered for a possible candidate of broadband wireless access networks and broadcasting applications. With an emphasis on a preamble design for multi-channel separation, we address a channel estimation based on the time-domain windowing and its imperfectness in OFDM-based multiple-antenna transmission systems. By properly designing each preamble for multiple antennas to be orthogonal in the time domain, the channel estimation can be applied to the HIPERLAN/2 and IEEE 802.11a standards in the case of more than two transmit antennas. Also, the effect of diversity techniques on the performance of OFDM-CDMA based broadband wireless access networks is investigated and the maximum achievable diversity gain for a two-path Rayleigh fading environment is evaluated. Simulation results show that the OFDM-CDMA system applying a space-time-frequency diversity with a full-rate full diversity code can give the diversity of D=4 and D=8 for both multi-user cases of maximum user and half user capacities, respectively.     

A One‐Kilobit PQR‐CMOS Smart Pixel Array

The photonic quantum ring (PQR) laser is a three dimensional whispering gallery (WG) mode laser and has anomalous quantum wire properties, such as microampere to nanoampere range threshold currents and √T‐dependent thermal red shifts. We observed uniform bottom emissions from a 1‐kb smart pixel chip of a 32×32 InGaAs PQR laser array flip‐chip bonded to a 0.35 µm CMOS‐based PQR laser driver. The PQR‐CMOS smart pixel array, now operating at 30 MHz, will be improved to the GHz frequency range through device and circuit optimization.     

Extraction of penicillin G from simulated media by an emulsion liquid membrane process

The extraction of penicillin G from simulated media was performed by water/oil/water (w/o/w) emulsion liquid membranes (ELMs) and studied under various operational conditions in a batch system. The degree of extraction achieved was between 80% and 95% under specific conditions. A concentration of greater than nine times the initial concentration of penicillin G in the external phase was obtained in the internal phase. The pH of the internal aqueous solution, containing a basic salt, was theoretically calculated on the basis of the amount of penicillin G transported into the internal phase. The calculated results agreed with the experimental data well and were used to select a suitable type and concentration of a basic salt in the internal phase to give a pH within the range 5 to 8 where penicillin G was stable after the termination of extraction. The extraction of penicillin G was successfully performed by the ELM process with sodium carbonate in the internal phase.     

Monolithic SiGe Up‐/Down‐Conversion Mixers with Active Baluns

The purpose of this paper is to describe the implementation of monolithically matching circuits, interface circuits, and RF core circuits to the same substrate. We designed and fabricated on‐chip 1 to 6 GHz up‐conversion and 1 to 8 GHz down‐conversion mixers using a 0.8 µm SiGe hetero‐junction bipolar transistor (HBT) process technology. To fabricate a SiGe HBT, we used a reduced pressure chemical vapor deposition (RPCVD) system to grow a base epitaxial layer, and we adopted local oxidation of silicon (LOCOS) isolation to separate the device terminals. An up‐conversion mixer was implemented on‐chip using an intermediate frequency (IF) matching circuit, local oscillator (LO)/radio frequency (RF) wideband matching circuits, LO/IF input balun circuits, and an RF output balun circuit. The measured results of the fabricated up‐conversion mixer show a positive power conversion gain from 1 to 6 GHz and a bandwidth of about 4.5 GHz. Also, the down‐conversion mixer was implemented on‐chip using LO/RF wideband matching circuits, LO/RF input balun circuits, and an IF output balun circuit. The measured results of the fabricated down‐conversion mixer show a positive power conversion gain from 1 to 8 GHz and a bandwidth of about 4.5 GHz.     

Shortest path algorithms: A computational study with the C programming language

The main purpose of this study is to evaluate the computational efficiency of algorithms for calculating shortest paths when they are correctly coded by using the C programming language. The eight algorithms that we selected for this experiment are the most efficient, either measured in terms of worst-case bounds or marked as such from previous computational studies; they include the redistributive heap algorithm. We suggest computer implementations that use the full power of C. In particular, the network representation and the various data structures used to keep the scan eligible list may be managed by using only additions and no multiplications, while it is not possible with FORTRAN. These capabilities, unique to C, yield several interesting conclusions: one may expect to speed up a shortest path algorithm by a factor of 20%; in some cases, this factor may reach 30%. Interestingly, the level of programming difficulty required to achieve these benefits is not greater than that required by implementations using arrays.     

A novel high-efficiency linear transmitter using injection-locked pulsed oscillator

This letter presents a novel high-efficiency linear transmitter using pulse-width modulation (PWM). An envelope of radio frequency (RF) input signal is modulated by the PWM. The modulated signal is applied to the gate bias of a class F injection-locked power oscillator and switches it on and off. By filtering the pulsed oscillating output signal of the injection-locked oscillator using high-Q bandpass filter, the input signal is restored. This technique enables the transmitter to have high efficiency with good linearity. Also, there is little distortion near saturation point of an active device. The measured results show efficiency of 54.6% and very good linearity in PCS band at 26.4-dBm output power.