Passivation of pigment-grade TiO(2) particles by nanothick atomic layer deposited SiO(2) films

Pigment-grade TiO(2) particles were passivated using nanothick insulating films fabricated by atomic layer deposition (ALD). Conformal SiO(2) and Al(2)O(3) layers were coated onto anatase and rutile powders in a fluidized bed reactor. SiO(2) films were deposited using tris-dimethylaminosilane (TDMAS) and H(2)O(2) at 500?°C. Trimethylaluminum and water were used as precursors for Al(2)O(3) ALD at 177?°C. The photocatalytic activity of anatase pigment-grade TiO(2) was decreased by 98% after the deposition of 2?nm SiO(2) films. H(2)SO(4) digest tests were performed to exhibit the pinhole-free nature of the coatings and the TiO(2) digest rate was 40 times faster for uncoated TiO(2) than SiO(2) coated over a 24?h period. Mass spectrometry was used to monitor reaction progress and allowed for dosing time optimization. These results demonstrate that the TDMAS-H(2)O(2) chemistry can deposit high quality, fully dense SiO(2) films on high radius of curvature substrates. Particle ALD is a viable passivation method for pigment-grade TiO(2) particles.     

Influence and comparison of emerging techniques of yarn manufacturing on physical–mechanical properties of polyester-/cotton-blended yarns and their woven fabrics

Abstract

In this study, the physical–mechanical properties of ring spun, ring compact, rotor and air-vortex yarns were investigated. The study was carried with yarn having linear densities of 24.4 tex and 36.7 tex, which were then converted to woven fabrics. The ring spun yarns have higher values of strength but also with higher strength irregularities. Extra-ordinarily low hairiness was observed in air-vortex yarns due to its unique yarn formation technique. The deviation rate (DR) of yarns have correlation with the mass spectrogram of respective yarns obtained from USTER Tester 5. Rotor and air-vortex yarns exhibited higher coefficient of friction. The woven fabrics made from ring spun yarns exhibited higher tensile and tear strength with higher elongation at break. The fabrics made from air-vortex yarns have very good pilling grade due to less protruding fibres on their surface and good structural integrity.     

Dietary Pigmentation and Deposition of α-Tocopherol and Carotenoids in Rainbow Trout Muscle and Liver Tissue

Rainbow trout (Oncorhynchus mykiss) were fed diets supplemented with canthaxanthin, oleoresin paprika and α-tocopherol. Canthaxanthin was more efficiently absorbed (3.8–7.9 mg/kg) in the flesh of rainbow trout than the paprika carotenoids (2.4–3.1 mg/kg). With increased pigmentation, decrease in lightness (L*) and hue angle, and increase in redness (a*) of the muscle were observed. Canthaxanthin produced more desirable reddish-pink color. Deposition of α-tocopherol in liver and muscle tissue increased with increase in dietary α-tocopheryl acetate. Fish receiving lower α-tocopheryl acetate reached maximum deposition levels earlier than those fed higher levels. There was no effect of α-tocopherol and carotenoid levels on muscle fatty acid composition.     

The effect of biphasic waveform tilt in transvenous atrial defibrillation

Atrial defibrillation can be accomplished using low energy shocks and transvenous catheters. The biphasic waveform tilt required to achieve optimal atrial defibrillation thresholds (ADFTs) is, however, not known. The effect of single capacitor biphasic waveform tilt modification on ADFT was assessed in 20 patients. Following AF induction the defibrillation pulses were delivered between the catheters positioned in the coronary sinus and the right atrium. The single capacitor biphasic waveform shocks, delivered over the same pathways, consisted of 65% tilt (65/65 biphasic waveform) to produce an overall tilt of 88%, or 50% tilt (50/50 biphasic waveform) to produce an overall tilt of 75%. Although 65/65 biphasic waveform delivers more energy, the shorter duration 50/50 biphasic waveform reduced stored energy ADFT 21%, from 1.34 +/- 0.82 J with 65/65 biphasic to 1.06 +/- 0.81 J. These differences were not statistically significant. Nine patients had lower ADFT with 50/50 biphasic waveform while five patients had lower ADFT with 65/65 biphasic waveform. Equivalent reduction in ADFT was seen in the remaining six patients. The ADFT was 0.83 +/- 0.65 J when both tilts were considered. In conclusion, biphasic waveform tilt modification may affect the ADFT in an individual patient. The optimal biphasic waveform for ADFT is not known.     

Numerical modelling of methane-powered micro-tubular, single-chamber solid oxide fuel cell

An experimentally validated, two-dimensional, axisymmetric, numerical model of micro-tubular, single-chamber solid oxide fuel cell (MT-SC-SOFC) has been developed. The model incorporates methane full combustion, steam reforming, dry reforming and water-gas shift reaction followed by electrochemical oxidation of produced hydrogen within the anode. On the cathode side, parasitic combustion of methane along with the electrochemical oxygen reduction is implemented. The results show that the poor performance of single-chamber SOFC as compared to the conventional (dual-chamber) SOFC (in case of micro-tubes) is due to the mass transport limitation on the anode side. The gas velocity inside the micro-tube is far too low when compared to the gas-chamber inlet velocity. The electronic current density is also non-uniform over the cell length, mainly due to the short length of the anode current collector located at the cell outlet. Furthermore, the higher temperature near the cell edges is due to the methane combustion (very close to the cell inlet) and current collection point (at the cell outlet). Both of these locations could be sensitive to the silver current collecting wire as silver may rupture due to cell overheating.     

Liquefaction of empty palm fruit bunch (EPFB) in alkaline hot compressed water

Effect of alkalis (NaOH, KOH and K₂CO₃) on liquefaction of EPFB (empty palm fruit bunch) biomass liquefaction was investigated under subcritical water conditions in a batch reactor operating at 270 °C and 20 bars for a period of 20 min. Catalytic performance and suitable biomass to water ratio that supported higher EPFB conversion, liquid hydrocarbons yield and lignin degradations were screened. Analytical results indicate that maximum of 68 wt% liquids were produced along with 72.4 wt% EPFB mass conversions and 65.6 wt% lignin degradation under 1.0 M K₂CO₃/2:10 (biomass/water) conditions. In comparison, the experiments that were performed in the absence of alkalis yielded only 30.4 wt% liquids, converted 36 wt% EPFB and degraded 24.3 wt% lignin. Furthermore, biomass to water ratios >2:10 decreased both solid mass conversion and liquid hydrocarbons' yield. The reactivity of the alkalis was in the order of K₂CO₃ > KOH > NaOH. The liquid compositions were dominantly phenols and esters; the highest value of phenol (60.1 wt% of liquid yield) was achieved in the case of K₂CO₃ (1.0 M) with 5 g EPFB/25 ml water ratio while 1.0 M NaOH yielded maximum esters (86.4 wt% of liquid yield). The alkali promoted process assisted with hot water treatments seemed promising for production of bio-oils from EPFB.     

An acidic ionic liquid-conventional alkali-catalyzed biodiesel production process

A study was undertaken to prepare biodiesel via two-step process using ionic liquid as first step catalyst due to the unsuitability of using the straight alkaline-catalyzed transesterification of high FFA presented in crude palm oil (CPO). In the first step, esterification of the FFA presented in the CPO was carried out using butylimidazolium hydrogen sulfate (BIMHSO₄), in which the acid value was reduced from 6.93 to 1.02mg KOH/g and then, KOH-catalyzed transesterification was applied. The conversion rate of FFA attained 85.3% when 4.8 wt% of BIMHSO₄ was applied to the reaction system containing methanol to CPO ratio of 12: 1 reacted at 170 °C for 150min. The final yield in 97.3% revealed that the process proposed in this study could lead to an excellent biodiesel meeting the ASTM requirements. Furthermore, this new two-step catalysis process could solve the old conventional catalysis process drawbacks.     

Structural,rheological, and mechanical properties of ternary blends of PEN,PET, and liquid crystalline polymer

Structural, rheological, and mechanical properties of ternary blends of a liquid crystalline copolyester (LCP) composed of p-hydroxybenzoic acid and 2,6-hydroxynaphthoic acid, poly(ehtylene naphthalate)(PEN), and poly(ethylene terephtalate) (PET) were investigated using capillary rheometry, tensile testing, scanning electron microscopy, and X-ray diffraction. Viscosity-shear rate behavior of the ternary blends is very similar to that of pure polymers and their binary blends. The activation energy of flows of the ternary blends was smaller than those of PEN and PET. Tensile modulus and strength of extruded strands of the blends increased with increasing LCP content. The extruded strands of the blends consist of a crystalline and oriented LCP phase and an amorphous and unoriented PEN/PET blended phase. Tensile mechanical properties and structures of the ternary blends were discussed.     

Efficient conversion of light paraffinic naphtha to aromatics over metal-modified Mo/MFI catalysts

Journal of Porous Materials - The transformation of light naphtha to value-added aromatic compounds is gaining momentum in the petrochemical industry. In this work, a series of metal modified...