Sequential Bayesian bit error rate measurement

As bit error rates decrease, the time required to measure a bit error rate (BER) or perform a BER test (i.e., to determine that a particular communications device's BER is less than some acceptable limit) increases dramatically. One cause of long measurement times is the difficulty of deciding a priori how many bits to measure to establish the BER to within a predetermined confidence interval width. This paper explores a new approach to deciding how many bits to measure, namely a sequential Bayesian approach. As measurement proceeds, the posterior distribution of BER is checked to see if the conclusion can be made that the BER rate is known to be within the desired range with high enough probability. Desired properties of the posterior distribution such as the maximum a postiori estimate and confidence limits can be computed quickly using off-the-shelf numerical software. Examples are given of using this method on bit error data measured with an Agilent 81250 parallel BER tester.     

A XRD study of Co/Au multilayers using a laboratory microdiffractometer

In this paper we show that by the analysis of 2D images collected with a laboratory X-ray microdiffractometer it is possible to non-destructively evaluate the structure, the microstructure, and the preferred orientation of films. In particular, the structural analysis of Co/Au multilayers on Si(1 0 0) deposited at different Ar pressures are reported and discussed.     

Formaldehyde content of milk in goats fed formaldehyde-treated soybean oil-meal

Formaldehyde is used in ruminant feeding for different purposes including the protection of dietary proteins from ruminal degradation. The formaldehyde content of milk of goats fed various levels of formaldehyde-treated soybean oil-meal has been determined by using a sensitive HPLC method. Results showed a significant linear correlation between ingested formaldehyde and formaldehyde concentration in milk. About 0.02% of ingested formaldehyde was excreted in milk, as free formaldehyde.     

Purification of Ellagic Acid by UF Membranes

Ellagic acid (2, 3, 7, 8‐tetrahydroxy(1)benzopyrano(5, 4, 3‐cde)(1)benzopyran‐5, 10‐dione) was selected as a model pollutant which is present in the tannic fraction of cork processing wastewater. The ultrafiltration of aqueous ellagic acid solutions through three membranes was studied in tangential UF laboratory equipment. Two of the membranes were polyethersulfone (Biomax10K and Biomax5K, with MWCO of 10000 and 5000 Da, respectively), and the third made of regenerated cellulose (Ultracel5K, with MWCO of 5000 Da). The water hydraulic permeability was evaluated for each membrane. The evolution of the permeate flow rate with processing time was followed, and the influence of the main operating variables (feed flow rate, trans‐membrane pressure and nature of the membranes) on the permeate flux was also established. According to the hypothesis of the film theory, the intrinsic and apparent rejection coefficients, as well as the mass transfer coefficients, were also determined, and the values obtained were discussed as a function of the operating conditions used.     

A case study of regional catchment water quality modelling to identify pollution control requirements.

There are four ecologically important river catchments that contain candidate Special Areas of Conservation (cSACs) under the Habitats Directive in the Lake District National Park located in the North of England. These are the rivers Ehen, Kent, Derwent and Eden. For each cSAC, there are defined ecological criteria that include water quality targets to protect the designated species. Stretches of the riverine cSACs in each catchment are failing to meet these and other water quality targets. The Environment Agency commissioned a study of each catchment to provide the underpinning scientific knowledge to allow it to deliver its statutory obligations under the Habitats Directive. SIMCAT river water quality models were produced and used to predict the water quality impacts resulting from a number of water quality planning scenarios aimed at achieving full compliance with the Habitats Directive and other national and EEC water quality targets. The results indicated that further controls on effluent discharges will allow the majority of targets to be met but other sources of pollution will also need to be controlled. The outcome of the study also recognised that water quality improvements alone will not necessarily produce the required improvement to the ecological interest features in each cSAC.     

Disc filtration for separation of flocs from a moving bed bio-film reactor.

A Discfilter with 10 and 18 microm filter openings, respectively, was placed in parallel to a flotation plant for separation of biological flocs from a post-denitrifying Kaldnes Moving Bed Process, the last treatment step at the municipal wastewater treatment plant at Sj?unda, Malm?, Sweden. The effluent concentrations from the 10 and 18 microm filter were 2-5 and 2-8 mg SS L(-1), respectively, which is comparable to, or better than, the flotation plant. Comparison with experiences from activated sludge plants shows that the Discfilter works especially well after the Kaldnes process. Particle size distribution (PSD) studies show that particles larger than the filter openings of 10 and 18 microm are separated with approximately 90% efficiency, whereas most of the smaller particles pass the filter. This fact indicates that the major particle separation mechanism is physical blocking. These findings point to the possibility of improving the prediction of the separation efficiency by combining measurements of turbidity and suspended solids with particle size analysis.