Over 80 Gbit/s 2:1 multiplexer and low power selector ICs using InP/InGaAs DHBTs

A 2:1 multiplexer (MUX) and low power selector ICs have been successfully designed and manufactured using an InP/InGaAs DHBT technology. The 2:1 MUX has been tested at data rates up to 80 Gbit/s with an output swing of 600 mV, while the selector IC has achieved operation speed up to 90 Gbit/s at a power consumption of only 385 mW.     

Power combining characteristics of backed-off traveling wave tubes for communications applications

Traveling wave tubes (TWTs) used in multi-tone and digital communications applications are typically operated backed off from saturation in order to improve the amplifier linearity. This reduces the bit error rate (BER), decreases intermodulation distortion and lowers adjacent channel power; all at the expense of reducing the average output power. For emerging telecommunications applications, the average power requirement is increasing to provide higher bit rates and lower BER, and often exceeds the power obtainable from backed-off space or telecommunications TWTs. One solution is to power combine TWTs that are operated 3 to 10 dB backed off from saturation. Efficient power combining requires that the phase and gain of the signal from each TWT be closely matched. To understand the variation in these parameters across a build-set of tubes, the phase and gain versus drive of 35 Boeing S-band 5525H TWTs were measured. The standard deviation in the phase about the mean phase shift measured at saturation was found to be 2.6/spl deg/, with a related standard deviation of the gain compression at saturation of 0.22 dB. These levels result in small power combining losses and small errors in phased-array fed multi-beam antennas in broadband multi-tone applications.     

Report of an IEEE Task Force?An IEEE Opinion on Research Needs for Biomedical Engineerng Systems

MORE than 200 years ago, our forefathers made note of man's inalienable rights to life, liberty, and the pursuit of happiness. To the engineering community (applied science in the service of man), these may be coincident with applications to medicine and biology (biomedical engineering), defense, and entertainment. Biomedical engineering research has the distinction, among these three missions, of not only contributing to the quality of human life through the industrial economy but also to life itself?the most fundamental concern of all people. It is through biomedical engineering research that we have been able to learn much concerning the functioning of living systems, and it is through such knowledge that we have been able to develop improved clinical diagnosis, monitoring, and treatment, including life-sustaining devices and aids to the handicapped. Each step represents an improvement in the quality of life, and each step forms the foundation upon which to gain new knowledge to improve upon earlier developments.     

Dimensional Effects on Magnetic Properties of Fe–Si Steels Due to Laser and Mechanical Cutting

Microstructural deterioration near the cut line and presence of residual stresses both affect the magnetic properties of cut parts. In this paper, the differences between microstructural deterioration resulting from mechanical and laser cutting as well as the sample size effects observed upon hysteresis will be discussed. It will be shown that the underlying mechanism for changes in magnetic properties due to mechanical cutting is distinct from that of laser cutting.      

Plastic material parameters and plastic anisotropy of tungsten single crystal: a spherical micro-indentation study

Enhancement of toughness is currently a critical engineering issue in tungsten metallurgy. The inherent toughness of tungsten single crystals is closely related to the capacity for local plastic slip. In this study we have investigated the plastic behavior of tungsten single crystals by means of micro-indentation experiments performed on specimens exposing (100), (110), and (111) surfaces. In parallel, FEM simulations were carried out with the Peirce–Asaro–Needleman crystal plasticity model considering both {110} 〈111〉 and {112} 〈111〉 slip systems. Plastic material parameters were identified by comparing the measured and predicted load–displacement curves as well as pile-up profiles. It is found that both measured and simulated plastic pile-up patterns on the indented surfaces exhibit significant anisotropy and orientation dependence, although the measured and simulated load–displacement curves manifest no such orientation dependence. The height and extension of pile-ups differ strongly as a function of surface orientation. The FEM simulations are able to reproduce the observed features of spherical indentation both qualitatively and quantitatively.     

Influence of the steel plate on the friction behavior of automotive wet disk clutches

Friction behavior is the key parameter for the design of automotive wet disk clutches. On the one hand, the Coefficient of Friction (CoF) level should be high to transmit torque efficiently. On the other hand, the clutch requires a positive slope of the CoF over sliding speed for good controllability, high comfort, and a low tendency to shudder. Clutches used in automatic or dual-clutch transmissions mostly use organic friction lining. These friction systems tend to have low CoF at low sliding speeds due to their high requirements regarding shifting comfort. Nevertheless, they show high values of CoF at high sliding speeds.

This study investigates the influence of different steel plate finishes on friction behavior in different application-relevant operation modes such as brake shift, unsteady slip, and micro slip. Each of these operation modes requires an accurate CoF measurement at different sliding speed ranges. Therefore, we use different test rig setups. We characterize the steel plates by their areal surface topography measured with an optical system using focus variation. We discuss differences in the friction behavior of the corresponding tribological systems at different operating conditions.

Results show an influence of the steel plate surface finish on the CoF level. Therefore, the surface finish of the steel plate influences the functional behavior of wet disk clutches and engineers should consider the surface finish in the early design phase. We discuss the correlation between commonly used surface parameters and friction parameters.

     

Iodine induced thyroid disease

Although iodine prevents goiter, enlarged thyroid glands continue to be detected in subjects, especially children, in spite of adequate iodine ingestion. Iodine may cause goiter in susceptible individuals by inhibiting the organic binding of iodine as is seen in adult asthmatics, neonates born of iodine ingesting mothers and in subjects residing along the littoral of Japan. Myxedema, especially in treated Graves' disease and Hashimoto's disease, may also be precipitated by iodine. On the other hand, iodine given to euthyroid subjects in areas of endemic goiter and to subjects with nontoxic nodular goiter may induce thyrotoxicosis by disclosing diffuse autonomously functioning thyroid tissue. An indirect adverse effect of iodine upon the thyroid gland may be manifested by lymphocyte glandular infiltrates and chronic thyroiditis which were sparse or absent in thyroid glands removed from subjects living in iodine deficient areas before iodine prophylaxis and therapy. Not only has the incidence of thyroiditis increased, but the histologic and clinical distinctions between treated Graves' disease and chronic thyroiditis have become indistinct. Experimentally, chronic thyroiditis has been produced in animals following large doses of iodine. Accumulated evidence supports the concept that iodine contributes to the genesis of chronic thyroiditis.     

The dependence of HNO2 mutagenesis in phage T4 on ligase and the lack of dependence of 2AP mutagenesis on repair functions

A temperature sensitive ligase allele of phage T4 reduced or eliminated HNO2 induced reversion of am mutants. Since at the temperatures used, the ligase mutant is defective in the repair of some types of lethal lesions (i.e., UV, MMS and EMS induced lesions) these results indicate that HNO2 mutagenesis may occur through a ligase dependent repair pathway. In contrast, 2AP induced mutation was not inhibited by mutants defective in the gene 30 ligase or in genes 32, 39, 41, 42, 44, 45, 46, 47, 49, 52, 56, 58-61 and v. This indicates that 2AP mutagenesis probably does not depend on a repair pathway in phage T4.     

Inbreeding and canine mammary cancer: a retrospective study

Using files of the Animal Neoplasm Registry (ANR) in Alameda and Contra Costa Counties, California, we conducted a retrospective study to compare the degree of inbreeding in the ancestry of purebred dogs with mammary and other cancers, and of those without tumors. Wright's coefficients of inbreeding, calculated for all animals in the three groups, ranged from 0.000 to 0.535. The median inbreeding coefficients of the mammary cancer and comparison groups (consisting of other cancers) were approximately twice that of the nonneoplastic group, but neither difference was statistically significant. Dogs with mammary adenocarcinoma and mixed mammary cancer had similar degrees of inbreeding.