Negative thermal expansion of laminates

Measurements have been carried out on the in-plane and through the thickness thermal expansion coefficients of glass polypropylene fibre composites of 50% volume fraction between room temperature and 120°C. Only in the temperature range 20° to 75°C are reproducible results obtained. It is confirmed that in-plane negative values may be obtained in specific directions. The physical reason for this and its connection with the necessary appearance of a large Poisson ratio is pointed out. The expansivity of the matrix material depends strongly on temperature. Very good agreement between the experimental values and those predicted from the properties of the two constituents is found provided that the value for the expansivity of the polyoropylene is that within the temperature range considered. It is shown that the polypropylene matrix does not provide a matrix which is stable enough in its properties to enable the system to yield consistent negative values of expansivity. An alternative system is proposed and a single experiment confirms that a negative value of the thermal expansivity of as large as –50 × 10^–6 K^–1 may be obtained.     

Feasibility study of absolute activity measurement with metallic magnetic microcalorimeters

We report on a feasibility study on precise determination of mass-specific activity of low-energy emitting radioisotopes. Conventional methods of activity measurement suffer from source self-absorption and a strong decrease in detection efficiency for low-energy electrons and photons. We propose a new method based on metallic magnetic microcalorimeters with the source embedded in the detector target in a 4π geometry. First results with a ⁵⁵Fe source show that electrons and photons are detected with a detection efficiency close to unity and with little loss of energy for electrons. The aim of this study is to provide standards of activity with very low uncertainties in the framework of radiation metrology.     

Using ion implantation to adjust the transition temperature of superconducting films

We summarize a continuing investigation into using ion implantation to alter the transition temperature of superconducting thin films. The primary motivation for the work presented here was to study the feasibility of using magnetic ion doping to replace the bi-layer T_c control process currently used for certain cryogenic detector applications at National Institute for Standards and Technology. The results from work with various ion species implanted into aluminum, molybdenum, titanium and tungsten host films are presented.     

Fine Purification of Monoisotopic Silanes 28SiH4 , 29SiH4 , and 30SiH4 via Distillation

High-purity isotopically enriched (99.98% ²⁸Si, 99.57% ²⁹Si, and 99.83% ³⁰Si) silane samples are prepared for the first time. The total hydrocarbon content of the samples is no higher than 0.1–0.3 ppm. The concentration of electroactive impurities in the silicon prepared from the purified monoisotopic silane is below 10¹⁵ cm^–3.     

Preparation and Properties of Er- and Yb-Activated TeO2–WO3 Glasses

TeO₂–WO₃ glasses coactivated with Er³⁺ and Yb³⁺ are prepared. The effect of Yb content on the efficiency of Er photoluminescence (PL) in the visible and IR spectral regions is studied. The highest PL efficiency is achieved at an Er : Yb atomic ratio of 1 : 1. The PL lifetime for the Er^{3+ 4} I _13/2 level is determined to be 7–9 ms.     

Surface Activation of Diamond Particles in the Process of Chemical Coppering

The effect of the composition of sensitizing–activating solutions on the activation efficiency and the chemical coppering of diamond powders is studied. The results demonstrate that stabilizing additives improve the stability of the solutions, influence the average coppering rate, and play a key role in determining the morphology and quality of the resultant coatings. The most effective stabilizing additive is synthamid-10, which ensures the deposition of high-quality copper coatings.     

Modeling and Analysis of a Long Thin Conducting Stripline

A long thin conducting stripline embedded in a dielectric and centered between two large conducting plates, i.e., the stripline environment, is considered. The stripline is modeled as infinitely long, infinitely thin, and perfectly conducting by first considering a stripline of finite length, thickness, and conductivity in a dielectric layer. Starting from Maxwell's equations and assuming that the current on the stripline is a propagating wave in length direction, asymptotic expressions for the fields inside and in the neighbourhood of the stripline are deduced. These expressions are used to model the stripline in the stripline environment, which leads to a boundary-value problem for the electric potential. This problem is solved by two different approaches, leading to integral equations for the current and for an auxiliary function describing the electric potential. A relation between the current and the auxiliary function is deduced, which is used to obtain asymptotic expressions for current and impedance. Results are compared with a numerical solution of the integral equation for the current and with results in literature.