Dynamic mechanical properties of agricultural residues‐filled polystyrene

Agricultural residues (cotton straw) were added as very small particles to polystyrene (PS) at different weight ratios by using a melt‐mixing technique. The dynamic mechanical tests were performed over a wide range of temperatures and frequencies by using an ARES rheometer (Rheometrics Scientific) operated in the dynamic mode. The dynamic mechanical properties in terms of the storage modulus (G′), loss modulus (G″), compliance moduli, loss tangent, and dynamic viscosity were studied and compared for PS and PS composite. The results showed that the dynamic mechanical moduli and viscosity were found to increase with the addition of cotton straw and rise further with its loading increasing. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 37–40, 2004     

Biodegradability of cellulose fabrics

Biodegradability of cellulose fabrics was evaluated by use of a soil burial test, an activated sewage sludge test, and an enzyme hydrolysis. Surface changes after biodegradation were observed by optical microscopy. From X‐ray diffraction analysis (XRD), changes in the crystallinities and the internal structures as a result of degradation were also investigated. It was shown that biodegradability decreased in the following order: rayon > cotton ? acetate. Rayon fibers, which have a low crystallinity and a low degree of orientation, showed the highest biodegradability in most cases. However, in spite of its low crystallinity, acetate fibers exhibited very low biodegradability, probably because of the presence of hydrophobic groups in its structure. On the other hand, linen showed an inconsistent behavior in that it had the highest biodegradability in the soil burial test, but a lower biodegradability than that of cotton in the activated sewage sludge test. XRD analysis revealed that there was a slight increase in the crystallinity of linen, cotton, and rayon fabrics at the initial stage, but a continuous decrease thereafter. From the correlation analysis, it was revealed that the biodegradability of cellulose fabrics was closely related to the moisture regain of the fibers, which reflects the hydrophilicity and internal structure of the fibers at the same time. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 248–253, 2004     

阻燃剂对软质聚氨酯泡沫燃烧特性的影响

利用锥形量热仪对添加了不同阻燃剂的软质聚氨酯泡沫，在25kW／m^2下，其热释放速率、产烟量、一氧化碳产生量、二氧化碳产生量和点燃时间等进行了试验研究。结果表明，含氯化铵的聚氨酯泡沫燃烧时热释放速率最小，仅是未经阻燃处理的聚氨酯泡沫的热释放速率的11．5％；含硫酸铵的聚氨酯泡沫的产烟量最少，仅是未经阻燃处理的聚氨酯泡沫的产烟量的6．4％；含氯化铵的聚氨酯泡沫燃烧时产生的一氧化碳和二氧化碳都是最少的，分别是未经阻燃处理的聚氨酯泡沫的2，4％和1．6％；点燃时间最长的是含四硼酸钠的聚氨酯泡沫，几乎是未经阻燃处理的聚氨酯泡沫的15倍，其它阻燃剂对聚氨酯泡沫的燃烧性能都有不同程度的影响。     

Isothermal crystallization kinetics and melting behavior of nylon/saponite and nylon/montmorillonite nanocomposites

DSC thermal analysis and X‐ray diffraction have been used to investigate the isothermal crystallization behavior and crystalline structure of nylon 6/clay nanocomposites. Nylon 6/clay has prepared by the intercalation of ε‐caprolactam and then exfoliating the layered silicates by subsequent polymerization. The DSC isothermal results reveal that introducing saponite into the nylon structure causes strongly heterogeneous nucleation induced change of the crystal growth process from a two‐dimensional crystal growth to a three dimensional spherulitic growth. But the crystal growth mechanism of nylon/montmorillonite nanocomposites is a mixed two‐dimensional and three‐dimensional spherulitic growth. The activation energy drastically decreases with the presence of 2.5 wt % clay in nylon/clay nanocomposites and then slightly increases with increasing clay content. The result indicates that the addition of clay into nylon induces the heterogeneous nucleation (a lower ΔE) at lower clay content and then reduces the transportation ability of polymer chains during crystallization processes at higher clay content (a higher ΔE). The correlation among crystallization kinetics, melting behavior, and crystalline structure of nylon/clay nanocomposites is also discussed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2196–2204, 2004     

Studies of surface and gas reactions in a catalytically stabilized combustor

A numerical investigation of a catalytically stabilized thermal (CST) combustor was conducted for a multichannel catalyst bed, and both the catalyst bed and thermal combustor were simultaneously modeled. The numerical model handled the coupling of the surface and gas reaction in the catalyst bed as well as the gas reaction in the thermal combustor. The behavior of the catalyst bed was investigated at a variety of operating conditions, and location of the flame in the CST combustor was investigated via an analysis of the distribution of CO concentration. Through parametric analyses of the flame position, it was possible to derive a criterion to determine whether the flame is present in the catalyst bed or the thermal combustor for a given inlet condition. The results showed that the maximum inlet temperature at which the flame is located in the thermal combustor increased with increasing inlet velocity.     

Synthesis and properties of poly(amide–imide)s based on N,N′‐bis(4‐carboxyphenyl)‐4,4′‐oxydiphthalimide,p‐aminobenzoic acid and various aromatic diamines

A new diimide–diacid monomer, N,N′‐bis(4‐carboxyphenyl)‐4,4′‐oxydiphthalimide (I), was prepared by azeotropic condensation of 4,4′‐oxydiphthalic anhydride (ODPA) and p‐aminobenzoic acid (p‐ABA) at a 1:2 molar ratio in a polar solvent mixed with toluene. A series of poly(amide–imide)s (PAI, III_a–m) was synthesized from the diimide–diacid I (or I′, diacid chloride of I) and various aromatic diamines by direct polycondensation (or low temperature polycondensation) using triphenyl phosphite and pyridine as condensing agents. It was found that only III_k–m having a meta‐structure at two terminals of the diamine could afford good quality, creasable films by solution‐casting; other PAIs III using diamine with para‐linkage at terminals were insoluble and crystalline; though III_g–i contained the soluble group of the diamine moieties, their solvent‐cast films were brittle. In order to improve their to solubility and film quality, copoly(amide–imide)s (Co‐PAIs) based on I and mixtures of p‐ABA and aromatic diamines were synthesized. When on equimolar of p‐ABA (m = 1) was mixed, most of Co‐PAIs IV had improved solubility and high inherent viscosities in the range 0.9–1.5 dl g^?1; however, their films were still brittle. With m = 3, series V was obtained, and all members exhibited high toughness. The solubility, film‐forming ability, crystallinity, and thermal properties of the resultant poly(amide–imide)s were investigated. © 2002 Society of Chemical Industry     

Properties and pervaporation separation of hydroxyl‐terminated polybutadiene‐based polyurethane/poly(methyl metharcylate) interpenetrating networks membranes

Hydroxyl‐terminated polybutadiene (HTPB), 4,4′‐dicyclohexyl methane diiscyanate (H₁₂MDI), and 1,4‐butane diol are used to synthesize polyurethane (PU) solutions by two‐stage process. Interpenetrating networks (IPNs) of HTPB‐based PU and poly(methyl methacrylate) (PMMA) with HTPB/MMA (wt/wt % ratio) = 2.0, 1.5, 1.0, 1.5, 0.8, and 0.6, which are designated as IPN1 to IPN5, respectively, are synthesized by sequential polymerization technique. Thermal properties, tensile strength, and contact angle of membranes increase with the increase of MMA content, while the elongation of membranes show the reverse trend. Characterization of membranes are investigated by C?C/C?O absorption ratio and infrared absorption frequency shiftment. These PU and IPN membranes are used for the separation of ethanol/water and isopropanol/water solution by pervaporation test. IPN3 membrane possesses the largest pervaporation permeability and the separation factor. The pervaporation results of ethanol/water feed has the same trend as that of isopropyl alcohol (IPA)/water solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Design and fabrication of 3D‐plotted polymeric scaffolds in functional tissue engineering

Regenerating the load‐bearing tissues requires 3D scaffolds that balance the temporary mechanical function with the biological requirements. In functional tissue engineering, designing scaffolds with biomimetic mechanical properties could promote tissue ingrowth since the cells are sensitive to their local mechanical environment. This work aims to design scaffolds that mimic the mechanical response of the biological tissues under physiological loading conditions. Poly(L ‐lactide) (PLLA) scaffolds with varying porosities and pore sizes were made by the 3D‐plotting technique. The scaffolds were tested under unconfined ramp compression to compare their stress profile under load with that of bovine cartilage. A comparison between the material parameters estimated for the scaffolds and for the bovine cartilage based on the biphasic theory enabled the definition of an optimum window for the porosity and pore size of these constructs. Moreover, the finite element prediction for the stress distribution inside the scaffolds, surrounded by the host cartilaginous tissue, demonstrated a negligible perturbation of the stress field at the site of implantation. The finite element modeling tools in combination with the developed methodology for optimal porosity/pore size determination can be used to improve the design of biomimetic scaffolds. POLYM. ENG. SCI., 47:608–618, 2007. © 2007 Society of Plastics Engineers.     

Biodegradation of low‐density polyethylene/thermoplastic starch foams before and after electron beam irradiation

Foamy low‐density polyethylene/plasticized starch (LDPE/PLST) blends at different compositions were produced in the presence of azodicarbonamide (ACA) compound as foaming agent. The LDPE/PLST blends before and after electron beam irradiation were investigated in terms of mechanical properties, bulk density, and structure morphology. Moreover, the biodegradability of these materials was evaluated by the soil burial test for 2 months, in which the buried sheets were also examined by scanning electron microscopy (SEM). The results showed that the increase of PLST content from 24 to 30% was accompanied by a decrease in the yield and break stresses of 10 and 20% for the unirradiated blends without the foaming agent, respectively. Further decrease in these mechanical parameters was observed after the foaming process. The bulk density, void fraction, cell size measurements as well as the examination by SEM illustrate clearly the cell growth of the foam structure. The soil burial test and SEM micrographs indicate the growth of microorganisms overall the blend sheets and that the blend was completely damaged after two months of burying. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Equilibrium and kinetic studies of the extraction of chelated copper(II) anions with Aliquat 336

The equilibrium and kinetics of solvent extraction of Cu²⁺ from aqueous solutions containing equimolar EDTA with Aliquat 336 in n‐decanol and kerosene at 298 K were investigated. The concentrations of Cu²⁺ (8–50 mol m^?3), Cl^? (5–60 mol m^?3), and Aliquat 336 (20–100 mol m^?3) were varied. A semi‐empirical model with three parameters was proposed to describe the equilibrium behavior, in which the non‐idealities in both aqueous and organic phases were considered. Over the ranges studied, the model agreed reasonably well with the experimental data (standard deviation, 15%). The forward and backward reaction rate constants were determined as (5.31 ± 0.16)×10^?6 m^9/4 mol^?3/4 s^?1 and (2.62 ± 0.09)×10^?7 s^?1, respectively, at 298 K. An interfacial reaction mechanism was proposed, which revealed that the reaction between the chelated anions and trimeric amine molecules at the interface was rate limiting. The derived rate laws were consistent with the experimental results. © 2002 Society of Chemical Industry