Beam test of the CsI(Tl) calorimeter for the BELLE detector at the KEK-B factory

We studied the performance of a prototype electromagnetic calorimeter for the BELLE detector at the KEK proton synchrotron for an energy range of 0.25–3.5 GeV. The prototype consisted of an array of 6 × 5 CsI(Tl) crystals with 30 cm length (16.2 radiation lengths) and about 6 cm × 6 cm cross section. The scintillation light of each CsI(Tl) crystal was read out by two large-area PIN photodiodes and charge-sensitive preamplifiers attached at the rear face of the crystal. We measured the energy and position resolution for electrons and the e/π separation for two sets of matrix configurations: one corresponded to the center and the other to the edge of the barrel calorimeter. The overall performance measured by the test proves that the prototype calorimeter is satisfactory for the use in the BELLE detector.     

Performance evaluation of the Golay code pulse compression technique

The Center for NDE, Iowa State University, has developed a laboratory prototype Golay code pulse compression system and tested it on a variety of materials. The performance of the system was evaluated in terms of signal-to-noise ratio enhancement (SNRE), resolution, and computation speed. The system's error sources also were discussed. The Golay code pulse compression was simulated on a computer and demonstrated the effective noise suppression. In addition, an equivalent pulse of the Golay code (delta-like pulse) was derived theoretically using a simple ultrasonic inspection model, which demonstrated its equivalence on the output correlated signal. Overall, the pulse compression technique extended the detection range for a given peak power and considerably reduced the system'swhite noise, hence providing enhanced signal-to-noise ratios (SNRs). An average of 30 dB improvement in SNR was obtained from highly energy-absorbent materials such as rubber, plastics, corks (insulation materials), and thick composites using the Golay codes of up to 512 bits. However, the technique did not effectively reduce coherent scattering noises from the coarse grain boundaries in cast stainless steels, Inconel weld metal, and material lay-ups in thin composites. Furthermore, it was found that, depending upon the system's hardware capabilities, the overall performance could be degraded considerably.     

Enhancement mode InP MISFET's with sulfide passivation andphoto-CVD grown P3N5 gate insulators

High performance enhancement mode InP MISFET's have been successfully fabricated by using the sulfide passivation for lower interface states and with photo-CVD grown P₃N₅ film used as gate insulator. The MISFET's thus fabricated exhibited exhibited pinch-off behavior with essentially no hysteresis. Furthermore the device showed a superior stability of drain current. Specifically under the gate bias of 2 V for 10⁴ seconds the room temperature drain current was shown to reduce from the initial value merely by 2.9% at the drain voltage of 4 V. The effective electron mobility and extrinsic transconductance are found to be about 2300 cm ²/V·s and 2.7 mS/mm, respectively. The capacitance-voltage characteristics of the sulfide passivated InP MIS diodes show little hysteresis and the minimum density of interface trap states as low as 2.6×10¹⁴/cm² eV has been attained     

Ultra-wideband (from DC to 110 GHz) CPW to CPS transition

A new ultra-wideband, low-loss and small-size coplanar waveguide (CPW) to coplanar strip (CPS) transition which can be used from DC to 110 GHz is presented. The proposed transition connects CPW with CPS by the reformed air-bridge. Two ground planes of CPW are tied at their ends by a line and the centre of the line is connected to the ground strip of CPS by another line. Owing to the symmetry of the proposed structure, the currents of two ground planes of CPW are combined with the same phase and transferred to the ground strip of CPS. With height of 3 μm, the signal line of CPW passes over two connecting lines and is connected to the signal strip of CPS. For the back-to-back transition structure, insertion loss <1 dB and return loss >15 dB are obtained from 0.5 to 110 GHz     

Preparation of core–shell type nanoparticles of diblock copolymers of poly(L‐lactide)/poly(ethylene glycol) and their characterization in vitro

Core–shell type nanoparticles of poly(L ‐lactide)/poly(ethylene glycol) (LE) diblock copolymer were prepared by a dialysis technique. Their size was confirmed as 40–70 nm using photon correlation spectroscopy. The ¹H‐NMR analysis confirmed the formation of core–shell type nanoparticles and drug loading. The particle size, drug loading, and drug release rate of the LE nanoparticles were slightly changed by the initial solvents that were used. The drug release behavior of LE core–shell type nanoparticles showed an initial burst during the first 12 h and then a sustained release until 100 h. The degradation behavior of LE block copolymer nanoparticles was divided into three phases: the initial rapid degradation phase, the stationary phase, and the rapid degradation phase until complete degradation. It was suggested that lidocaine release kinetics were predominantly governed by the diffusion mechanism in the initial burst phase and after that by both of the diffusion and degradation mechanisms. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2625–2634, 2002     

Activity of NiO in (Ni,Mg)O Solid Solutions

Disagreement exists in the literature concerting the activity of NiO in (Ni,Mg)O solid solutions. Ideal behavior, as well as strong positive deviations and strong negative deviations from ideality, has been reported. In the present study, the activity of NiO was determined by electromotive force measurements using the solid-state cell Pt/Ni-NiO/0.92ZrO₂-0.08Y₂O₃/Ni-(Ni,Mg)O/Pt. The compositions studied had NiO mole fractions of 0.1,0.3,0.5,0.7, and 0.9. In agreement with theoretical expectations, the solid solutions exhibited ideal behavior at 882° and 982°C. Possible reasons for the conflicting results in the literature arc presented.     

The prospects of non-volatile phase-change RAM

Phase-change read-and-write memory (PRAM) is a promising memory that can solve the problems of conventional memory—scalability, read/write speed, and reliability. We will review the opportunities and technical challenges of PRAM. The most important challenge of PRAM is the reduction of the writing current. Various approaches to reduce the writing current will be reviewed and the prospects of PRAM are discussed.     

On‐Line Detection Of State‐Of‐Charge In Lead Acid Battery Using Radial Basis Function Neural Network

To realize a stable supply of electric power in an automobile, an accurate and reliable detection method of SOC (state‐of‐charge) in a lead acid battery is required. However the dynamics of the battery is very complicated. The characteristics of the battery greatly change due to its degradation. Moreover a automobile has many driving patterns, which are unknown beforehand. Thus it is not easy to detect the SOC analytically. In this paper, to overcome this problem, a new on‐line SOC detection method with a radial basis function neural network is proposed. In order to increase the detection accuracy of degraded batteries, physical values related to the degradation degree are used as input signal in the neural network. The detection accuracies for different sized batteries and various degradation states are investigated.     

Droplet de-entrainment by inertial impaction on vertical rods in an air-droplet mixture flow

We experimentally investigate the de-entrainment of droplets by inertial impaction on an array of vertical rods in an air-droplet mixture flow. The de-entrainment efficiencies are measured for a single rod, for a single row of rods, and for a multi-row of rods. We investigate the effects of the droplet mass flux (0.5–5.4 kg/m² s), the droplet Weber number (3000–8000), the air velocity (0–6 m/s), the rod geometry, and the surface roughness on the de-entrainment, and the rod diameter-to-pitch ratio effect on the de-entrainment. The results for a single rod show that the de-entrainment efficiency decreases slightly as the droplet mass flux increases; however, in our experimental ranges, there is negligible dependence on the droplet Weber number, the air velocity, and the surface roughness. The rod geometry affects the de-entrainment efficiency. The results for a single row of rods show that the existence of neighboring rods promotes de-entrainment due to droplet splashing, and we develop a correlation to show the effect of diameter-to-pitch ratio on the de-entrainment. Using information on the de-entrainment efficiencies of a single rod and those of a single row of rods, we propose a correlation that predicts the de-entrainment efficiency for a multi-row of rods with a staggered array. The RMS errors of the correlation from the de-entrainment efficiencies experimentally obtained are within 13.5%.     

A finite element analysis of damage propagation during metal forming process

In this paper damage propagation during metal forming process is investigated with the concept of continuum damage mechanics. An isotropic damage model based on the theory of materials of type N is adopted to describe the damage process of a ductile material with large elasto-viscoplastic deformation. To solve the finite elasto-viscoplasticity problem, a reasonable kinematic strain measure for largely deformed solids is used and the damage constitutive equations based on thermodynamical framework are developed. The stiffness degradation of the loaded material is chosen as a damage measure. An extended interior penalty method is used to impose the contact condition on the boundary. The highly nonlinear equilibrium equations are reduced to the incremental weak form and approximated by the total Lagrangian finite element method. The displacement control method along with the modified Riks' continuation technique based on displacement parameter is used to solve the incremental iterative equations. As numerical examples, upsetting, backward extrusion and punch problems are simulated and the results of damage propagation and J₂ stress contours with and without damage are presented. For punch problems, spring back and residual stresses are also presented.