Electrochemical properties of boron-carbon-nitride films formed by magnetron sputtering

The electrochemical behavior of B_1.0C_2.4N_1.0 thin film was investigated in acidic, neutral and alkaline solutions. The anodic polarization curve of the film in 1 M NaOH showed the anodic dissolution of the film. The curve of the film in 1 M HCl showed no anodic dissolution. The cathodic polarization curve in 1 M NaCl showed shift to a negative potential side, but the anodic polarization curve was the same as that of Pt. The anodic dissolution in 1 M NaOH depended on potentials, that is, no anodic dissolution was recognized in a potential range of −0.2 to 0.1 V but the dissolution rate increased with increasing potential in a range of 0.1-0.6 V. The anodic current density of the film is directly proportional to the dissolution rate at potentials higher than 0.1 V. The dissolution rate of the film was increased with increasing solution pH.     

Solid extraction of caffeine and theophylline from green tea by molecular imprinted polymers

This paper involves a feasibility study on using molecular imprinted polymers as the sorbent materials in solid phase extraction for caffeine and theophylline from green tea. Two kinds of MIPs, with caffeine-theophylline mixture and pentoxifylline-theophylline mixture as the templates respectively, MAA as the monomer, EDMA as the crosslinker and ATBN as the initiator, were applied to this purpose. Mixture solution of caffeine and theophylline (1 Μg/ ml in acetonitrile) was applied to the solid extraction cartridges following a load, wash and elute procedure with acetonitrile, methanol, methanol-acetic acid (90/10, v/v) as the solvents, respectively. This solid phase extraction protocol was applied for extraction of caffeine and theophylline from green tea. Comparison between the results obtained with the MIPs cartridges and a traditional C₁₈ reversed-phase cartridge was made. It showed that the MIP-based sorbent on the solid phase extraction was comparable with that of C₁₈ material. HPLC analysis using a C₁₈ column (5 Μm, 250× 4.6 mm from Rstech corporation), methanol: water (60 :40, v/v) as the mobile phase at a flow rate of 0.6 ml/min was applied for the quantitative determination.     

Mobile phase composition for resolving whey proteins in reversed-phase high performance liquid chromatography

Reversed-phase high-performance liquid chromatography was successfully developed for the simultaneous and rapid separation for the main whey proteins, α-Lactalbumin and β-Lactoglobulin. This method consisted of a linear gradient of the two mobile phases of 0.1% trifluoroacetic acid in water and 0.1% trifluoroacetic acid in acetonitrile. The total run time for this separation was approximately 30 min, and α-Lactalbumin was eluted followed byβ- Lactoglobulin. The injection volume was fixed at 20 μl and the flow rate was 1 ml 1/min. The optimum mobile phase composition and gradient conditions to separate α-Lactalbumin and β-Lactoglobulin (A+B) were experimentally obtained at the 15 μm particle with a pore size of 300 Å on the linear-gradient mode.     

Fabrication of SiO2-ZrO2 composite fiber mats via electrospinning

(1 − x)SiO₂-(x)ZrO₂ (x = 0.1, 0.2) composite fiber mats were prepared by electrospinning their sol-gel precursors of zirconium acetate and tetraethyl orthosilicate (TEOS) without using a polymer binder. The electrospun composite fibers were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FT-IR) and mercury porosimetry. The composite fibers having a tetragonal crystalline ZrO₂ were obtained by calcining the electrospun composite fibers at high temperatures. The results show that the structure and crystallization of ZrO₂ in the composite fibers can be controlled by sintering temperature, while the porosity and morphology of the fiber mats did not depend on the sintering temperature.     

Synthesis and properties of acrylonitrile-CR-methyl methacrylate graft copolymer

Graft copolymerization of acrylonitrile (AN) and methyl methacrylate (MMA) onto polychloroprene (CR) was carried out using benzoyl peroxide as initiator. The effects of mole ratio of AN to MMA, reaction temperature, reaction time, solvent, and initiator concentration on the graft copolymerization were examined. It was found that the thermal stability and weatherability of the AN—CR—MMA graft copolymer (ACM) were considerably better than those of CR.     

Polymer gel electrolytes prepared from P(EG‐co‐PG) and their nanocomposites using organically modified montmorillonite

Polymer gel electrolytes were prepared by thermal crosslinking reaction of a series of acrylic end‐capped poly(ethylene glycol) and poly(propylene glycol) [P(EG‐co‐PG)] having various geometries and molecular weights. Acrylic end‐capped prepolymers were prepared by the esterification of low molecular weight (M_n: 1900–5000) P(EG‐co‐PG) with acrylic acid. The linear increase in the ionic conductivity of polymer gel electrolyte films was observed with increasing temperature. The increase in the conductivity was also monitored by increasing the molecular weight of precursor polymer. Nanocomposite electrolytes were prepared by the addition of 5 wt % of organically modified layered silicate (montmorillonite) into the gel polymer electrolytes. The enhancement of the ionic conductivity as well as mechanical properties was observed in the nanocomposite systems. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 894–899, 2004     

Improvement of cyclodextrin glucanotransferase as an antistaling enzyme by error-prone PCR

In an effort to improve the properties of cyclodextrin glucanotransferase (CGTase) as an antistaling enzyme, error-prone PCR was used to introduce random mutations into a CGTase cloned from alkalophilic Bacillus sp. I-5 (CGTase I-5). A mutant CGTase[3-18] with the three mutations M234T, F259I and V591A was selected by agar plate assay. Sequence alignment of various CGTases indicated that M234 and F259 are located in the vicinity of the catalytic sites of the enzyme and V591 in the starch binding domain E. The cyclization activity of CGTase[3-18] was dramatically decreased by 10-fold, while the hydrolyzing activity was increased by up to 15-fold. These mutations near subsite +1 (M234T) and at subsite +2 (F259I) are likely to alter the enzyme activity in a concerted manner, promoting hydrolysis of substrate while retarding cyclization. The addition of CGTase[3-18] reduced the retrogradation rate of bread by as much as did the commercial antistaling enzyme Novamyl during 7-day storage at 4 degrees C. No cyclodextrin (CD) was detected in bread treated with CGTase[3-18], whereas 21 mg of CD per 10 g of bread was produced in bread treated with wild-type CGTase.     

Computational fluid dynamics (CFD) analysis and experimental study for toxic hazardous waste destruction in the cavity incinerator

We undertook numerical and experimental studies to develop a better incineration method for the destruction of CC1₄. A phenomenological model for the turbulent reaction of CC1₄, including a flame inhibition feature, has been successfully incorporated into a commercial code, simulating the incineration processes of this compound. The gaseous flow solution was obtained using SIMPLEST, a derivative of Patankar’s SIMPLE algorithm, with a k-ε turbulence model. A modified fast chemistry turbulent reaction model was developed to describe the flame inhibition due to the presence of CC1₄, considering the corresponding burning velocity data of these mixtures. An experiment was carried out on a 5.2 kW laboratory scale, transportable, cavity-type incinerator, which warrants a sufficient residence time and effective turbulent mixing by the formation of a strong recirculation region in a combustor. To this end, the specific configuration of the incinerator was manufactured to consist of two opposing jets and a rearward facing step. The calculated data were in close agreement with the experimental data for the concentrations of major species, such as CCI₄ and HCl, together with the temperature profiles. The experimental test gave the desired DRE of above 99.99%.     

Synthesis and characterization of in situ polymerized segmented thermoplastic elastomeric polyurethane/layered silicate clay nanocomposites

Nanocomposites based on thermoplastic elastomeric polyurethane (TPU) and layered silicate clay were prepared by in situ synthesis. The properties of nanocomposites of TPU with unmodified clay were compared with that of organically modified clay. The nanocomposites of the TPU and organomodified clay showed better dispersion and exhibited superior properties. Exfoliation of the clay layers was observed at low organoclay contents, whereas an intercalated morphology was observed at higher clay contents. As one of major purposes of this study, the effect of the silicate layers in the nanocomposites on the order–disorder transition temperature (T_ODT) of the TPU was evaluated from the intensity change of the hydrogen‐bonded and free carbonyl stretching peaks and from the peak position change of the N? H bending peak. The presence of the organoclay increased T_ODT by approximately 10°C, which indicated improved stability in the phase‐separated domain structure. The layered silicate clay caused a tremendous improvement in the stiffness of the TPU; meanwhile, a reduction in the ultimate elongation was observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3048–3055, 2006     

Synthesis and non‐isothermal crystallization behavior of poly(ethylene phthalate‐co‐terephthalate)s

A series of poly(ethylene phthalate‐co‐terephthalate)s were synthesized by melt polycondensation of ethylene glycol (EG) with dimethyl phthalate (DMP) and dimethyl terephthalate (DMT) in various proportions. The DMT‐rich polymers were obtained with reasonably high molecular weights, whereas the DMP‐rich polymers were synthesized with relatively low molecular weights due to steric effects associated with the highly kinked DMP monomer. The compositions and thermal properties of the polymers were determined. The copolymers containing DMP in amounts of ≤ 21 mol% were crystallizable, whereas the other polymers were not. All the polymers exhibited a single glass transition temperature. Analysis of the measured glass transition temperatures and crystal melting temperatures confirmed that the DMT‐rich copolymers are random copolymers. The non‐isothermal crystallization behaviors of the DMT‐rich copolymers were investigated by calorimetry and modified Avrami analysis. The Avrami exponents n were found to range from 2.7 to 3.8, suggesting that the copolymers crystallize via a heterogeneous nucleation and spherulitic growth mechanism; that is, the incorporation of DMP units as the minor component does not change the growth mechanism of the copolymers. In addition, the activation energies of the crystallizations of the copolymers were determined; the copolymers were found to have higher activation energies than the PET homopolymer. Polym. Eng. Sci. 44:1682–1691, 2004. © 2004 Society of Plastics Engineers.