Piezoelectric Multilayer Ceramic/Polymer Composite Transducer with 2–2 Connectivity

A multilayer piezoelectric ceramic/polymer composite with 2–2 connectivity was fabricated by thermoplastic green machining after co-extrusion. The multilayer ceramic body was composed of piezoelectrically active lead zirconate titanate (PZN)–lead zinc niobate (PZN)-lead zirconate titanate (PZT) layers and electrically conducting PZN–PZT/Ag layers. After co-extruding the thermoplastic body, which consisted of five piezoelectric layers interspersed with four conducting layers, it was computer numeric-controlled machined to create periodic channels within it. Following binder burnout and sintering, an 18 vol% array of 190 μm thin PZT slabs with a channel size of 880 μm was fabricated. The channels were filled with epoxy in order to fabricate a PZN–PZT/epoxy composite with 2–2 connectivity. The piezoelectric coefficient (effective d ₃₃) and hydrostatic figure of merit ( d _h× g _h) of the PZN–PZT/epoxy composite were 1200 pC/N and 20 130 × 10⁻¹⁵ m²/N, respectively. These excellent piezoelectric characteristics as well as the relatively simple fabrication procedure will contribute in widening the application range of the piezoelectric transducers.     

Maximizing SNR in improper complex noise and applications to CDMA

The optimum linear time-invariant (LTI) filter that maximizes the signal-to-noise ratio (SNR) is, in general, the solution to an integral equation. This is the well-known matched filter. With regards to the detection of bandpass signals, we present the full form of the integral equation using the complex baseband representation of signals. The correct form of the complex integral equation includes, in addition to the autocorrelation function, a pseudoautocorrelation function which vanishes for most applications. However, in the presence of improper complex noise, overlooking the pseudoautocorrelation leads to a “nonoptimal” filter. To illustrate the concept, we apply the theory to a direct-sequence code-division multi-access (DS-CDMA) system in which improper complex noise arises. In the application, we derive the SNR maximizing filter and the nonoptimal filter and compare their near-far resistances     

The dendritic growth of γ′ precipitates and grain

The growth pattern of γ precipitates in the grains and at the grain boundaries has been investigated in a Ni-24Co-4Al-4Ti-5Cr-5Mo (weight percent) alloy of very small lattice misfit between the precipitate and the matrix phases under varying heat-treatment conditions. When aged at temperatures lower than the solvus temperature (T _s = 1150 °C) by more than 30 °C after direct cooling from the solution-treatment temperature, the nucleation density is high. In this condition, the supersaturation is quickly removed because of the overlapping diffusion fields and the precipitates undergo Ostwald ripening from the early stage. The precipitates then have an equilibrium shape of spheres in the grains and truncated spheres at nearly straight grain boundaries. The precipitates at the grain boundaries are coherent with one of the grains, and their number density is not much larger than that in the grains, apparently because of a large contact angle (about 150 deg) with the grain boundary. Quenching the alloy after the solution treatment and aging at any temperature also produce high precipitate number density and equilibrium shapes. When aged at temperatures just belowT _s (above 1140 °C), the nucleation density is low, the precipitates grow dendritically in the grains, and the grain boundaries become serrated. The observed dendritic growth characteristics do not quantitatively agree with the predictions of Mullins and Sekerka theory, but the discrepancy may be due to the uncertainties in both the observed and calculated quantities. By deeply etching the matrix, it is shown that the grain boundary serration is produced by the precipitates growing preferentially in the direction of the incoherent boundary because of the rapid solute diffusion along the grain boundary. The dendritic growth and grain boundary serration can be obtained also by slowly cooling through the temperature range just belowT _s.     

High-temperature polyimide nanofoams for microelectronic applications

Foamed polyimides have been developed in order to obtain thin film dielectric layers with very low dielectric constants for use in microelectronic devices. In these systems the pore sizes are in the nanometer range, thus, the term ‘nanofoam’. The polyimide foams are prepared from block copolymers consisting of thermally stable and thermally labile blocks, the latter being the dispersed phase. Foam formation is effected by thermolysis of the thermally labile block, leaving pores of the size and shape corresponding to the initial copolymer morphology. Nanofoams prepared from a number of polyimides as matrix materials were investigated as well as from a number of thermally labile polymers. The foams were characterized by a variety of experiments including TEM, SAXS, WAXD, DMTA, density measurements, refractive index measurements and dielectric constant measurements. Thin film foams, with high thermal stability and low dielectric constants approaching 2.0, can be prepared using the copolymer/nanofoam approach.     

Integrated modelling under uncertainty in watershed-level assessment and management.

Uncertainty in water quality model predictions is inevitably high due to natural stochasticity, model uncertainty, and parameter uncertainty. An integrated modelling system (modified-BASINS) under uncertainty is described and demonstrated for use in receiving-water quality prediction and watershed management. A Monte Carlo simulation was used to investigate the effect of various uncertainty types on output prediction. Without pollution control measures in the watershed, the concentrations of total nitrogen (T-N) and total phosphorus (T-P) in the Hwaong Reservoir, considering three uncertainty types, would be less than about 4.4 and 0.23 mg L(-1), respectively, in 2012, with 90% confidence. The effects of two watershed management practices, wastewater treatment plants (WWTP) and constructed wetlands (WETLAND), were evaluated. The combined scenario (WWTP + WETLAND) was the most effective at improving reservoir water quality, bringing concentrations of T-N and T-P in the Hwaong Reservoir to less than 3.4 and 0.14 mg L(-1), 24 and 41% improvements, respectively, with 90% confidence. Overall, the Monte Carlo simulation in the integrated modelling system was practical for estimating uncertainty and reliable in water quality prediction. The approach described here may allow decisions to be made based on the probability and level of risk, and its application is recommended.     

An empirical investigation of socio-cultural factors of information sharing in China

Understanding information sharing is an important challenge to modern organizations, and is likely to be increasingly considered when IT investment decisions are made world-wide. Our research study investigated the influence of cultural factors on information sharing in China. It was postulated that social network structures such as guanxi, Confucian dynamism, and collectivism could explain the degree to which information sharing took place between people in China. It was found that guanxi, Confucian dynamism, and collectivism all had a significant influence on information sharing.     

Perioperative specific management of blood volume loss in craniosynostosis surgery

Accurate assessment and replacement of blood loss and fluid-electrolyte deficit during craniosynostosis repair is difficult owing to patient size and the diversity of surgical technique. Forty-three patients undergoing primary craniosynostosis repair over a 10-year period were studied retrospectively to determine blood loss and fluid deficit and to assess blood transfusion practices during both intraoperative and postoperative periods. Blood loss was calculated on the basis of estimated red cell mass (ERCM) and fluid-electrolyte imbalance was investigated with blood samplings. Blood transfusion was considered appropriate if the postoperative or posttransfusion ERCM was within 12% of the preoperative value. Estimated fluid requirement (EFR) was used in 4 ml kg(-1) h(-1) except for neonates. Intraoperatively, 80% of all patients were appropriately managed with respect to blood transfusion and EFR. Postoperatively only 20% of the patients receiving transfusions were transfused appropriately. In 23.3% of these patients (10/43) unexpected respiratory distress developed immediately after their recovery from the anesthesia. With the measurement of estimated blood volume and allowable blood loss, appropriate transfusion could be achieved for the successful treatment of the primary craniosynostosis.     

High-performance simulations of turbulent boundary layer flow using Intel Xeon Phi many-core processors

The Journal of Supercomputing - Direct numerical simulations (DNS) of turbulent flows have increasing importance because they not only provide fundamental understanding of turbulent flows but also...     

Millisecond-order rapid micromixing with non-equilibrium electrokinetic phenomena

We report an active micromixer utilizing vortex generation due to non-equilibrium electrokinetics near micro/nanochannel interfaces. Its design is relatively simple, consisting of a U-shaped microchannel and a set of nanochannels. We fabricated the micromixer just using a two-step reactive ion etching process. We observed strong vortex generation in fluorescent microscopy experiments. The mixing performance was evident in a combined pressure-driven and electroosmotic flows, compared with the case with a pure pressure-driven flow. We characterized the micromixer for several conditions: different applied voltages, ion concentrations, flow rates, and nanochannel widths. The experimental results show that the mixing performance is better with a higher applied voltage, a lower ion concentration, and a wider nanochannel width. We quantified the mixing characteristics in terms of mixing time. The lowest mixing time was 2 milliseconds with the voltage of 230 V and potassium chloride solutions of 0.1 mM. We expect that the micromixer is beneficial in several applications requiring rapid mixing.