钽粉颗粒强度的研究

研究了采用激光粒度分布仪测试电容器级团化钽粉粒度分布及强度的方法。其中心内容是:先采用3种不同比表面积、松装密度和费氏平均粒径的钠还原原粉,按3种烧结工艺制得团化钽粉。然后把烧结得到的6种试样加入纯水中,以200～300r/min进行高速搅拌并以40W,42kHz超声波振动。将激光衍射分析仪的激光束穿过经不同搅拌时间的悬浊钽粉,测得不同时间的钽粉粒径分布曲线。分析分布曲线可以获得团化钽粉的一系列信息,包括:①几种团化钽粉颗粒的相对强度;②影响团化钽粉颗粒强度的因素;③钽粉强度和其他性能如介电损耗、流动性,平均粒径及密度的关系等。     

稀土锆酸盐的制备和热膨胀性能

采用固相反应法制备了稀土锆酸盐材料.通过XRD图谱和SEM对材料的显微结构进行分析,并测试了不同温度下材料的热膨胀系数.结果表明稀土锆酸盐材料的热膨胀系数大约为11×10-6/℃,其值随着温度的升高而升高,升高的速率逐渐减小.随着原子序数的增大,热膨胀系数是逐渐减小的,这说明稀土锆酸盐材料的热稳定性是随着原子序数的增大逐渐增强的.     

纳米粉及添加剂对压电陶瓷材料性能的影响

采用高能球磨法研磨出PZT-5纳米粉料，添加外购的纳米有机添加剂，按照传统的固相工艺法制备出了压电陶瓷材料，研究分析纳米粉料和纳米有机添加剂对压电陶瓷性能的影响。通过测试分析可以看出，纳米压电粉料与纳米有机添加剂的综合作用，降低了材料的烧结温度、相对介电常数εr,Qm值和以d31，提高了压电应变常数d333，从而压电电压常数g33、gh、dh成倍提高，这些对制作宽带、高灵敏度的换能器是很有好处的。     

Structure and blood compatibility of tetrahedral amorphous hydrogenated carbon formed by a magnetic-field-filter plasma stream

Tetrahedral amorphous hydrogenated carbon (ta-C:H) films with various substrate bias voltages were prepared using a magnetic-field-filter plasma stream deposition system. The microstructural and optical properties were studied using ellipsometric spectra. The refractive index n of each sample was obtained by simulating their ellipsometric spectral using Tauc-Lorentz oscillator model, and then the relative sp³ C ratio of each sample was calculated using Bruggeman effective medium approximation. The sp³ C fraction of each sample was quantified by using electron energy-loss spectroscopy (EELS). The blood compatibility of the samples was evaluated by tests of platelet adhesion, kinetic clotting time and thrombin time. The quantity and morphology of the adherent platelets on the surface of these samples were investigated using scanning electron microscopy. Results show that the spectroscopic ellipsometry is a helpful method to evaluate the sp³ carbon fraction of the carbon films. The substrate bias voltage has an obvious effect on sp³ content and blood compatibility of ta-C:H films. The sample prepared with substrate bias voltage of − 20 V showed the best blood compatibility. A simple bio-physical hypothetical model was proposed to explain the experiment results.     

Modeling of Intercritical Heat Treatment of DP and TRIP Steels

The final microstructure of DP and TRIP assisted steels can evolve after hot working (hot rolling) or during post heat treatment process. In the formation of the final structure a number of different technological parameters have important roles, e.g. end temperature of rolling, cooling rates, temperature of intercritical annealing, etc. As a result of the individual factors and their combinations a lot of product technology routes are feasible. The effect of the different combinations of these technological parameters on the microstructure can be mapped by the special Jominy end-quench test (so called intercritical Jominy end-quench test) described in this paper. Unlike the traditional Jominy test, in this case there is a partial anstenizing between A1 and A3 temperatures which results in a given amount of ferrite in the microstructure before quenching. The method developed can be applied for mapping DP and TRIP assisted steels' microstructure in a wide range of technological parameters. The analysis of measured and calculated data can help us find the technological parameters optimal from the microstructural point of view.     

Ti9Al合金的氢塑性效应

采用真空自耗电弧炉熔炼制备Ti9Al合金，通过渗氢处理显著提高氢含量，在凸轮塑性试验机ЧПИ-2上以10mm／min的速度进行热模拟试验。研究发现：氢可以降低Ti9Al合金的相变温度，扩大α β区的温度范围；氢作为卢稳定剂会妨碍或完全抑制以Ti3Al为基的α2相的析出；钛合金的氢合金化可促使卢相在更低温度下稳定化，明显地提高了Ti9Al合金塑性。     

铜塔铸造工艺

介绍了五台山铜塔铸造工艺,由于其结构特殊,故采用了3种工艺分别铸造而成:细砂湿模造型、树脂砂毁模贴皮造型和熔模铸造.介绍了铜塔表面化学着色技术.铜塔铸造工艺对其他相似艺术铸品具有一定的借鉴价值.     

Effects of CeF3 on properties of self-shielded flux cored wire

0 IntroductionSelf-shielded flux cored wire is a newly developedwelding material used without gas protection. Use of suchcored wires has grown rapidly in developed countriesbecause of the following advantages: simple use, goodwind resistance ability, lower cost resulted from highproductivity and strong desulfurization ability[1]. Self-shielded flux cored wires are preferred for on-site weldingsuch as ship and barge building, storage tank, bridge,offshore oil platform buildings and so on[2 -3].…     

QH－1型扁环填料的气液接触性能

本文简要介绍了新近研制的ＱＨ－１型扁环填料对于汽液接触过程的流体力学与传质性能。实验表明，这种填料具有通量大、阻力小、传质效率高的优点，可望代替鲍尔环等常用填料，以取得良好经济效益     

超细纤维素胶体和丙烯酰胺的接枝共聚

本文用纤维素材料经酸分解制备具有平衡聚合度（LODP）的微晶纤维素，再分散成超细纤维素胶体（准均相纤维素体系）。用扫描电镜（SEM）观察处理前后的纤维素颗粒尺寸，并比较它们和丙烯酰胺接枝共聚的反应速率、聚合转化率、接枝率、接技效率、聚丙烯酰胺支链的分子量及其分布的情况。