High Temperature Property Development of Bauxite Based Bricks

Physical properties and microstructural evolution on firing of 3 types of bauxite based refractory bricks were carried out using techniques such as porosimetry,XRD and SEM.The groups differed from each other by progressive refining of the matrix or bond phase.It is revealed that such a refinement of the matrix can improve the high temperature properties of the bricks made from poor grade materials.     

Weakening Water Rights and Efficient Transfers 1

For more than half a century, in nearly all western states, the regulatory agencies (the State Engineer or equivalent) used impairment of other water rights as the primary criterion for approving or rejecting change applications to move water to higher-valued uses. In recent years, however, protests to change applications have been brought by 'stakeholders' who do not own water rights, but who argue that they are affected by water transfers. Under the impairment rule, these parties do not have statutory standing to protest successfully. But they have brought legal suits to block transfers, and the courts have considered whether additional criteria involving 'impacts on social welfare' are needed to evaluate transfers. State Supreme Court rulings on such suits in Utah and Nevada are reviewed as prototype cases. The Utah court held that additional 'social welfare' criteria must be utilized by the State Engineer in evaluating change applications, whereas the Nevada court held that such criteria were already incorporated in existing water statutes and administrative practice. The critical question raised in the paper is whether existing state regulatory agencies can effectively implement a real 'social welfare' criterion to evaluate change applications. The conclusion is that they probably cannot, and that if they try, water allocations will be politicized to a much greater extent than they are now, and efficient market transfers will be impeded if not completely prevented.     

A biochar from casein and its properties

A biochar was prepared by pyrolysis of casein. A helium and mercury porosimeter were used to measure the true and apparent densities of the chars respectively, elemental and IR analysis were used to characterize the chemical composition of char. A SEM was used to observe the char surfaces in order to verify the presence of porosity. The biochar has 9.02% of nitrogen, content of porosity is 20%. The experimental results show that it is possible to prepare chars with relatively high porosity from casein for the further preparation of activated carbon.     

Reliability studies of MOCVD TiSiN and EnCoRe Ta(N)/Ta

Passivated single damascene copper SiO₂ damascene lines were evaluated in combination with TiSiN and Ta(N)/Ta diffusion barriers. Leakage current, breakdown and time-dependent dielectric breakdown properties were investigated on a wafer level basis for temperatures ranging between room temperature and 150 °C. It is found that the leakage performance of the wafers with a TiSiN barrier is better at room temperature, but at 150 °C the performance levels out with Ta(N)/Ta. Time-dependent dielectric breakdown measurements at 150 °C show that the lifetime of the interconnect is higher with the selected Ta(N)/Ta barrier than for TiSiN.     

Platinum Binuclear Complexes as Phosphorescent Dopants for Monochromatic and White Organic Light‐Emitting Diodes

Efficient blue‐, green‐, and red‐light‐emitting organic diodes are fabricated using binuclear platinum complexes as phosphorescent dopants. The series of complexes used here have pyrazolate bridging ligands and the general formula C^∧NPt(μ‐pz)₂PtC^∧N (where C^∧N = 2‐(4′,6′‐difluorophenyl)pyridinato‐N,C^2′, pz = pyrazole ( 1 ), 3‐methyl‐5‐tert‐butylpyrazole ( 2 ), and 3,5‐bis(tert‐butyl)pyrazole ( 3 )). The Pt–Pt distance in the complexes, which decreases in the order 1 > 2 > 3 , solely determines the electroluminescence color of the organic light‐emitting diodes (OLEDs). Blue OLEDs fabricated using 8 % 1 doped into a 3,5‐bis(N‐carbazolyl)benzene (mCP) host have a quantum efficiency of 4.3 % at 120 Cd m^–2, a brightness of 3900 Cd m^–2 at 12 V, and Commission Internationale de L'Eclairage (CIE) coordinates of (0.11, 0.24). Green and red OLEDs fabricated with 2 and 3 , respectively, also give high quantum efficiencies (～ 6.7 %), with CIE coordinates of (0.31, 0.63) and (0.59, 0.46), respectively. The current‐density–voltage characteristics of devices made using dopants 2 and 3 indicate that hole trapping is enhanced by short Pt–Pt distances (< 3.1 Å). Blue electrophosphorescence is achieved by taking advantage of the binuclear molecular geometry in order to suppress dopant intermolecular interactions. No evidence of low‐energy emission from aggregate states is observed in OLEDs made with 50 % 1 doped into mCP. OLEDs made using 100 % 1 as an emissive layer display red luminescence, which is believed to originate from distorted complexes with compressed Pt–Pt separations located in defect sites within the neat film. White OLEDs are fabricated using 1 and 3 in three different device architectures, either with one or two dopants in dual emissive layers or both dopants in a single emissive layer. All the white OLEDs have high quantum efficiency (～ 5 %) and brightness (～ 600 Cd m^–2 at 10 V).     

Intelligent process analytics for CRM

Many organisations use decision models in their processes such as tables or trees to provide decision support to their operational divisions. For example, in fault management, customer contact centre operators usually use a decision model in the form of prescribed interviews. Based on the answers given by customers, the operator navigates through the decision model to reach an assessment of the problem. In order to achieve customer satisfaction and operational excellence, it is very important to constantly monitor the performance of a decision model not only on an overall level, but also on the level of individual decisions. In this paper we present a configurable business process analytics tool, known as the intelligent Universal Service Management System, that constantly monitors decision data and is capable of optimising the decisions based on high-level business objectives. We explain the various features of the software and show how it can be used to optimise decision processes. We also show how we can easily provide a customised version to monitor the performance of provision processes.     

Fault detection for control of wastewater treatment plants.

Interest in real-time model-based control is increasing as more and more facilities are being asked to meet stricter effluent requirements while at the same time minimizing costs. It has been identified that biological process models and automated process control technologies are being used at wastewater treatments plants throughout the world and that great potential for optimising biotreatment may exist with the integration of these two technology areas. According to our experience, wastewater treatment plants are indeed looking for ways to successfully integrate their modelling knowledge into their process control structure; however, there are practical aspects of this integration that must be addressed if the benefits of this integration are to be realised. This paper discusses the practical aspects of monitoring, filtering and analysing real sensor data with an aim to produce a reliable real-time data stream that might be used within a model-based control structure. Several real case study examples are briefly discussed in this paper.     

Evaluation and optimization of package processing and design through solder joint profile prediction

Solder joints are generated using a variety of methods to provide both mechanical and electrical connection for applications such as flip-chip, wafer level packaging, fine pitch, ball-grid array, and chip scale packages. Solder joint shape prediction has been incorporated as a key tool to aid in process development, wafer level and package level design and development, assembly, and reliability enhancement. This work demonstrates the application of an analytical model and the Surface Evolver software in analyzing a variety of solder processing methods and package types. Bump and joint shape prediction was conducted for the design of wafer level bumping, flip-chip assembly, and wafer level packaging. The results from the prediction methodologies are validated with experimentally measured geometries at each level of design.