Production of Gentiobiose from Hydrothermally Treated Aureobasidium pullulans β-1,3-1,6-Glucan

We report production of the functional disaccharide gentiobiose β-D-Glcp-(1→6)-D-Glc by a hydrolysis reaction of hydrothermally treated Aureobasidium pullulans β-1,3-1,6-glucan as the substrate and Kitalase as the enzyme. Gentiobiose was produced over the pH range 4−6 and the concentration of gentiobiose produced decreased above pH 7. The maximum value of gentiobiose production was unaffected by the enzyme concentration. The maximum concentration of gentiobiose produced was dependent on the substrate concentration whereas the maximum ratio of gentiobiose to glucose was not. The production of gentiobiose from yeast β-1,3-1,6-glucan was lower than that from A. pullulans β-1,3-1,6-glucan.     

Sieving of aerosol particles with metal screens

Metal screens with uniform micrometer-sized opening were employed to sieve aerosol particles by suppressing the adhesion of particles smaller than the openings. The collection efficiencies of monodispersed polystyrene latex (PSL) particles were experimentally determined using the metal screens with 1.2, 1.8, 2.5, and 4.2 μm openings at various filtration velocities. The particles smaller than the mesh opening adhered on the metal screen at a low filtration velocity, but the bounce-off of particles on the mesh surface suppressed the adhesion at a high velocity. As a result, we found that the adhesion of PSL particles larger than 0.3 μm mostly suppressed at a filtration velocity higher than 10 m s^?1 and therefore we can sieve aerosol particles according to the opening size of metal screens. We also found that the particle number concentration could be determined by measuring the increase in pressure drop since the clogging of metal screen openings takes place by the individual particles.

© 2016 American Association for Aerosol Research     

New Approach for Macro Porous RB‐SiC Derived from SiC/Novolac‐type Phenolic Composite

A novel fabrication route to make macroporous silicon carbide (SiC) has been proposed in this study. The route is composed of the following two steps: the fabrication of porous α‐SiC/novolac‐type phenolic composite using hexamethylenetetramine (HMT) as a curing/blowing agent for the novolac monomer and a conventional reaction‐bonded (RB) sintering of the composite. The α‐SiC/novolac‐type phenolic composite was carbonized at 800°C for 2 h in N₂ gas and then reacted with the molten silicon at 1450°C for 30 min under vacuum, resulting in the macroporous RB‐SiC with an open porosity of 48% and relatively large pore size of ~110 μm. The compressive strength of the macroporous RB‐SiC was 113 MPa, which is relatively high compared to those reported for macroporous SiC of equivalent porosities and pore sizes.     

Numerical analysis to study the effect of through thickness reinforcement with different stitch orientations on open-hole laminates

The effect of through thickness reinforced open-hole laminates was analysed in terms of laminate behaviour under in-plane tensile loading based on continuum mechanics. Stitches around the notch were oriented in the longitudinal and transverse directions. To obtain the macroscopic damage and the local stress–strain constitutive behaviour, laminates were modelled on a lamina-wise basis. Interfaces between lamina and stitch yarns were assumed to be perfectly glued and modelled by the contact capability. Discretisation procedures using the principle of virtual work were applied in addition to discretisation of the contact traction. Progressive failure analysis with Puck’s failure criteria was conducted to characterise the failure behaviour of the laminate. In both cases, damage was initiated by a matrix crack in the perpendicular direction of the loading axis on the notch. The longitudinally stitched laminate showed a 14.29% higher strength compared to the transversely stitched laminate by suppressing damage propagation. The results obtained using this finite element technique was consistent with the experimental results.     

Focus on Extracellular Vesicles: Development of Extracellular Vesicle-Based Therapeutic Systems

Many types of cells release phospholipid membrane vesicles thought to play key roles in cell-cell communication, antigen presentation, and the spread of infectious agents. Extracellular vesicles (EVs) carry various proteins, messenger RNAs (mRNAs), and microRNAs (miRNAs), like a “message in a bottle” to cells in remote locations. The encapsulated molecules are protected from multiple types of degradative enzymes in body fluids, making EVs ideal for delivering drugs. This review presents an overview of the potential roles of EVs as natural drugs and novel drug-delivery systems.     

Mechanism of Magnetite Seam Formation and its Role for FeO Scale Transformation

The phase transformation behavior of a thermally grown oxide scale of FeO on pure-Fe and an Fe–2wt%Au alloy was investigated. Particular attention was paid to formation of a magnetite seam, which is the Fe₃O₄ layer formed at the FeO/alloy interface at an initial stage of the phase transformation, since it has important effects on the overall phase transformation of FeO scale. A thin Au(Fe) layer was found to develop on the Fe–Au alloy at the FeO/alloy interface after 32 min of oxidation at 750 °C in air. This Au(Fe) layer prevented formation of a magnetite seam and accelerated the FeO eutectoid reaction. The Au(Fe) layer acted as a “chemical diffusion barrier” for inward diffusion of Fe from the FeO to the alloy substrate across the FeO/alloy interface and prevented magnetite seam formation.     

Experimental study of impingement cooling by heat sinks with thin longitudinal fins for LSI packages

This paper reports on the impingement cooling characteristics of a heat sink with thin longitudinal fins of 0.2 mm thickness, which are spaced with a fin-pitch in the range 0.5 mm to 2.0 mm. The air cooling of the heat sink comes from a slot-shaped orifice positioned above the heat-sink center. The breadth of the gap between the fin tops and the inlet orifice is in the range 0 mm to 10 mm. The thermal resistance of the thin longitudinal fins used is about 50% to 57% that of the thick longitudinal fins now in commercial use. The cooling performance of the thin-plate fins is almost the same as that of optimally arranged pin-fins with the same total surface area. A maximum value of six times the heat transfer rate of a single flat plate having the same base area was observed for the thin-plate fins. A comparison of cooling performance between impingement and channel flow systems was conducted. The performance of impingement cooling systems is almost unaffected by the breadth of the gap between the fin tops and the inlet orifice (or, for channel cooling, the upper wall). On the other hand, the performance of channel-cooling systems decreases significantly as the gap widens. © 1997 Scripta Technica, Inc. Heat Trans Jpn Res, 25(7): 449–459, 1996     

Effects of EDTA saturated with Ca2+ (Ca-EDTA) on pig,bovine and mouse oocytes at the germinal vesicle stage during maturation culture and the involvement of chelation of Zn2+ in pronuclear formation induction by Ca-EDTA

EDTA saturated with Ca(2+), Fe(3+) or Cu(2+) can induce parthenogenetic activation of pig oocytes at the germinal vesicle stage, whereas EDTA saturated with Zn(2+), which is unable to chelate Zn(2+), does not, indicating that chelation of Zn(2+) with EDTA saturated with Ca(2+) (Ca-EDTA) in maturing pig oocytes plays a pivotal role in the induction of parthenogenetic activation of oocytes. In the present study, the involvement of Zn(2+) chelation in the induction of parthenogenetic activation of pig oocytes at the germinal vesicle stage was confirmed first by examining the effects of concomitant addition of Zn(2+), Cu(2+) or Ni(2+) at various concentrations together with 1 mmol Ca-EDTA l(-1) to the maturation medium. The titration experiments revealed that the pronuclear formation induced by 1 mmol Ca-EDTA l(-1) was completely inhibited by the addition of > 30 micromol Zn(2+) l(-1) to the medium, but not by the addition of Cu(2+) and Ni(2+) at any concentration examined. Second, bovine and mouse oocytes at the germinal vesicle stage were cultured in medium with or without 1 mmol Ca-EDTA l(-1) for 48 h to examine the effects of Ca-EDTA treatment on these oocytes during maturation culture. Most (70-86%) of the bovine oocytes that underwent germinal vesicle breakdown matured to the MII stage via the MI phase, regardless of whether Ca-EDTA was present for the first 24 h of culture. However, 61% of oocytes that had been cultured with Ca-EDTA for 48 h formed a pronucleus without a second polar body, whereas oocytes cultured in the absence of Ca-EDTA were not observed to form a pronucleus at any time during culture. However, even when mouse oocytes at the germinal vesicle stage were cultured for up to 48 h in maturation medium containing Ca-EDTA, pronuclear formation was not observed. Finally, when bovine oocytes that had been cultured with 1 mmol Ca-EDTA l(-1) for 48 h from the germinal vesicle stage were cultured further in medium without Ca-EDTA that was supplemented with 5% fetal calf serum, only 26% of the oocytes developed to the cleaved stage, and none could develop further.     

Frequency-Dependent Properties of the Hyperpolarization-Activated Cation Current,If, in Adult Mouse Heart Primary Pacemaker Myocytes

A number of distinct electrophysiological mechanisms that modulate the myogenic spontaneous pacemaker activity in the sinoatrial node (SAN) of the mammalian heart have been investigated extensively. There is agreement that several (3 or 4) different transmembrane ionic current changes (referred to as the voltage clock) are involved; and that the resulting net current interacts with direct and indirect effects of changes in intracellular Ca²⁺ (the calcium clock). However, significant uncertainties, and important knowledge gaps, remain concerning the functional roles in SAN spontaneous pacing of many of the individual ion channel- or exchanger-mediated transmembrane current changes. We report results from patch clamp studies and mathematical modeling of the hyperpolarization-activated current, I_f, in the generation/modulation of the diastolic depolarization, or pacemaker potential, produced by individual myocytes that were enzymatically isolated from the adult mouse sinoatrial node (SAN). Amphotericin-mediated patch microelectrode recordings at 35 °C were made under control conditions and in the presence of 5 or 10 nM isoproterenol (ISO). These sets of results were complemented and integrated with mathematical modeling of the current changes that take place in the range of membrane potentials (−70 to −50 mV), which corresponds to the ‘pacemaker depolarization’ in the adult mouse SAN. Our results reveal a very small, but functionally important, approximately steady-state or time-independent current generated by residual activation of I_f channels that are expressed in these pacemaker myocytes. Recordings of the pacemaker depolarization and action potential, combined with measurements of changes in I_f, and the well-known increases in the L-type Ca²⁺ current, I_CaL, demonstrated that I_CaL activation, is essential for myogenic pacing. Moreover, after being enhanced (approximately 3-fold) by 5 or 10 nM ISO, I_CaL contributes significantly to the positive chronotropic effect. Our mathematical model has been developed in an attempt to better understand the underlying mechanisms for the pacemaker depolarization and action potential in adult mouse SAN myocytes. After being updated with our new experimental data describing I_f, our simulations reveal a novel functional component of I_f in adult mouse SAN. Computational work carried out with this model also confirms that in the presence of ISO the residual activation of I_f and opening of I_CaL channels combine to generate a net current change during the slow diastolic depolarization phase that is essential for the observed accelerated pacemaking rate of these SAN myocytes.