Polysaccharides as excipients for colon-specific coatings. Permeability and swelling properties of casted films

Oligosaccharides such as inulin (In) and polysaccharides such as galactomannans, combined with polymethacrylates on isolated films for film coatings, were obtained from aqueous-based solvents and investigated as potential vehicles for colonic drug delivery. These compositions, which are susceptible to fermentation by colonic microflora, constitute promising excipients for the development of new colon-specific therapeutic systems. The characteristics of several compositions have been demonstrated in permeability and swelling studies on isolated films composed of a polymethacrylate associated with In or galactomannans of mesquite seed gum (MSG). Results reported prove a dependency of the properties of mixed films on the polymethacrylate-polysaccharide concentration ratio and on the composition of the dissolution media. An increase in permeability through the mixed films was observed in a simulated colonic environment for the following compositions: Eudragit®RS30D-MSG 70 : 30 w/w; Eudragit® RS30D-In 90 : 10 w/w; Eudragit®RS30D-In 76 : 24 w/w.     

Optical properties of end-sealed hollow fibers

We propose sealing techniques for medical hollow fibers to protect the inner surface of fibers from debris or water that scatters from targets. First, hollow fibers are sealed with a film of polymer that is easily formed by use of a dipping technique. The transmission loss of 20-microm-thick sealing film was 0.2 dB for Er:YAG laser light, and the maximum energy that is available for the film was 180 mJ. Second, a sealed glass cap was applied to the output end of hollow fiber. The silica-glass cap with a wall thickness of 400 microm shows a transmission loss of 0.5 dB and was not damaged by radiation of 400-mJ energy pulses.     

Catalytic oxidation of hydrogen chloride in a fluid bed reactor

The Deacon reaction (HCI + 1/4 O₂ ⇋ 1/2 Cl₂ + 1/2 H₂O) was studied in a catalytic fluid bed reactor. Reaction rates found from measurements in differential and integral reactors were represented by the Langmuir-Hinshelwood type rate equation. Considering the effect of catalysts in the dilute phase, it was found that conversions in a fluid bed reactor can be calculated without any modifying parameters. It is pointed out that the wake fraction, which has been necessary to consider for fast reactions in a fluid bed reactor, is attributed to the dilute phase effect.     

The presence of Penicillium and Penicillium mycotoxins in food wastes

A total of 97 samples (48 summer and 49 winter) of food waste from private households were investigated for Penicillium and for mycotoxins. Twenty-five Penicillium species were isolated and Penicillium crustosum, Penicillium brevicompactum, Penicillium chrysogenum, Penicillium expansum, Penicillium roqueforti, Penicillium spinulosum, Penicillium viridicatum, Penicillium commune, Penicillium citrinum and Penicillium solitum were, in decreasing order, the most frequently identified species. Mycotoxins produced by several of these species, including mycophenolic acid, roquefortine C, penitrems A-F and thomitrems A and E, were detected. Of the 48 summer samples, 36 were severely infected and contained more than 10(5) colony forming units (CFU) Penicillium/g sample. The levels of mycotoxins in these samples were in the range 75-19000 microg/kg mycophenolic acid, 40-920 microg/kg roquefortine C, 35-7500 microg/kg penitrem A, 20-2100 microg/kg thomitrem A and 20-3300 microg/kg thomitrem E. Of the 49 winter samples, only one was found to contain mycophenolic acid (4800 microg/kg) and roquefortine C (190 microg/kg), and this sample was severely infected with P. roqueforti. Thirty samples of food waste collected from the food manufacturing industry were also investigated. The number of Penicillium in these samples was between 10(5) and 10(6) colony forming units (CFU)/g sample. Seven of these samples contained mycophenolic acid ranging from 50 to 600 microg/kg and three of these samples also contained roquefortine C in the range 100-250 microg/kg.     

Contact and interconnect formation on compound semiconductor devices by ionized-cluster beam deposition

A new deposition technology, namely the ionized-cluster beam deposition method, was applied to form contacts and interconnects on III–V compound semiconductor devices. Au alloy films deposited by this technology had strong enough adhesion to an insulator layer to be a satisfactory interconnection. A step approximately 8 μm high at an angle of 90° to the semiconductor was covered fully with an Au alloy film obtained by this method. Electrical ohmic contacts for p-type GaP and GaAs were successfully obtained at substrate temperatures of 400 °C and 300 °C respectively without any further annealing process; this resulted in better device characteristics because of the lower process temperatures and also made the device less expensive because of a reduction in fabrication time.     

Design principle of micromechanical probe with an electrostatic actuator for friction force microscopy

It is important to understand friction force in micro/nano mechanical devices both at high sliding speed and with high lateral resolution. Dual-axis friction force microscopes that can provide high lateral resolution and accuracy have been proposed; however, the sliding speed is limited by the probe scan speed. While a micro mechanical probe (MMP) with an electrostatic actuator can overcome this problem, details of probe design have not been established yet. This paper presents the principle of the mechanical design for an MMP with high force sensitivity and sufficient drive force. The dimensions of the double cantilever beam control the spring constants, resonant frequencies, and drive force. The use of an actuated MMP enables accurate friction force microscopy at high sliding speeds, which is required for the design of micro/nano mechanical devices.     

A new data mining approach to estimate causal effects of policy interventions

This paper presents a data driven approach that enables one to obtain a measure of comparability between-groups in the presence of observational data.The main idea lies in the use of the general framework of conditional multiple correspondences analysis as a tool for investigating the dependence relationship between a set of observable categorical covariates X and an assignment-to-treatment indicator variable T, in order to obtain a global measure of comparability between-groups according to their dependence structure. Then, we propose a strategy that enables one to find treatment groups, directly comparable with respect to pre-treatment characteristics, on which estimate local causal effects.     

Reduction of nitric oxide with activated PAN fibres

The reductive removal of nitric oxide from flue gases by reaction with polyacrylonitrile-based active carbon fibres (PAN-ACF) activated with sulphuric acid has been studied at 423–632 K, using a circulating flow reactor. Nitric oxide (0.67 mmol) was completely removed via reduction with 1 g activated carbon under optimum conditions in 210 and 60 min at 423 and 623 K, respectively. N₂ was formed as NO was removed. Some oxygen remained on the carbon surface at 423 K, but was desorbed as CO or CO₂ on subsequent heating to 623 K. The bimolecular reaction of NO reduction over PAN-ACF, and the possible active sites of oxygen surface groups are discussed in the light of a kinetic study and a comparison of the fibre activation at different temperatures.     

Algorithms for solving large-scale 0–1 goal programming and its application to reliability optimization problem

Goal programming(GP) is one of the most widely used Operations Research/Management Science/Industrial Engineering techniques for solving multiple criteria decision making (MCD M) problems. In the realistic decision making problems, many GP problems are involved a large number of 0–1 decision variables and a special type of system structures.

Inthis paper, we develop a computational algorithm for solving 0–1 goal programming with a generalized upper bounding (GUB) structures. From the views of the computational experience and storage requirement, we implemented an efficient software package for UN IX workstations in which we called it micro 0–1 GP(GUB). In the micro 0–1 GP(GUB) developed here, the GUB structures would be effectively handled and we designed user-friendly GP data entry subsystem.

As a real-world 0–1 goal programming problem with the GUB structures, we demonstrate an optimization problem of system reliability for allocating redundant units by the micro 0–1 GP(GUB) software package on an UN IX system.