Fluidised pellet bed bioreactor: a promising technology for onsite wastewater treatment and reuse.

A pilot-scale fluidised pellet bed (FPB) bioreactor, which combines chemical coagulation, biological degradation, particle pelletisation and separation in one unit, was applied for onsite wastewater treatment and reuse. As a result of rational use of inorganic coagulant and organic polymer and moderate mechanical agitation, spherical particles were generated in the upflow column and a well-fluidised bed was formed. With a continuous supply of dissolved oxygen through a recycling loop, an aerobic condition was kept in the bottom section of the FPB column. Under such conditions the pellets in the FPB column showed the following characteristics: (1) compact structure and high density; (2) rich in microorganisms; and (3) high MLSS and MLVSS concentrations. Therefore, the FPB bioreactor achieved more than 90% removal of SS, COD, BOD and TP from raw domestic wastewater within a total hydraulic retention time (HRT) of only about 30 minutes. It also showed nitrification and denitrification ability and the TN removal could be about 50% as the recycling ratio was increased to 1:1. The treated water quality is generally competitive with the secondary effluent from a conventional activated sludge process. With these advantages the FPB bioreactor is recommendable as a compact system for onsite wastewater treatment and reuse.     

As,Sb,Sn对30CrMnSiA钢力学性能的影响

在３０ＣｒＭｎＳｉＡ钢中加入不同量的Ａｓ，Ｓｂ，Ｓｎ元素，研究了这些元素单独存在及复合存在时对钢的强度，塑性，冲击韧度及韧脆转变温度的影响规律，并用扫描电镜及俄歇能谱分析了Ａｓ，Ｓｂ，Ｓｎ导致晶界脆化的机理。     

Designing the MPC105 PCI bridge/memory controller

The MPC105 peripheral component interconnection bridge/memory controller provides a platform-specification-compliant bridge between Power PC microprocessors and the PCI bus. With it, designers can create systems using peripherals already designed for a variety of standard PC interfaces. This bridge chip also integrates a secondary cache controller and high-performance memory controller that supports DRAM or synchronous DRAM and ROM or flash ROM     

Rate sensitivity of high birefringent fiber optic sensors underlarge dynamic loads

New experimental studies on the effects of large dynamic compressive loads on highly birefringent optical fibers are presented. The intensity rate of applied dynamic loads ranged between 2.18-6719 KN/m-sec. A Fibercore (previously York) HB600 Bow-Tie fiber with an initial beat length of 1.16 mm was employed in the present study. Sensor response is discussed in terms of the effects of force amplitudes and velocities on the calibration parameter T_f. T_f is a function of the amplitude as well as the velocity of applied loading. Therefore, calibration of the sensor should be achieved through regression analysis of the load-fringe data for the entire spectrum of the desired force velocities. The ramification of this finding is that a single experiment for the measurement of T_f cannot provide the required parameters for calibration. This further implies that the change in beat length is also dependent on the amplitude and velocity of loading. The suggested method takes both effects into account through empirical analysis of experimental data     

C60 Detection in Soot Formed in Benzene Liquid Spray Combustion in a Shock Tube

H.P.L.C. and mass spectrometry.     

Grassmannian, central projection, and output feedback poleassignment of linear systems

A sufficient rank condition for arbitrary pole assignability by static output feedback of m-input, p-output linear systems of McMillan degree n相似文献   

Insight into an unsupervised two-step sparse transfer learning algorithm for speech diagnosis of Parkinson’s disease

Neural Computing and Applications - Speech diagnosis of Parkinson’s disease (PD) as a non-invasive and simple diagnosis method is particularly worth exploring. However, the number of samples...     

Intrinsically patterned electrical systems: physical requirements and experimental demonstration

Microsystem Technologies - This paper introduces a method of replicating electrical circuits through a series of specific requirements as part of a design methodology referred to as Intrinsically...     

Surface analytical study of the interaction between γ-amino propyl triethoxysilane and E-glass surface

Time-of-flight secondary ion mass spectrometry has been used to study the interaction of -amino propyl triethoxysilane with an E-glass surface. The fragmentation pattern has been interpreted by assigning a series of mass peaks to the structural unit of the poly(aminosiloxane). The composition of the coating is complicated by the presence of polydimethylsiloxane and its copolymers. The highest mass fragment was obtained from the coating exposed by extraction with warm water (697 AMU). The largest molecular fragments would appear to have degrees of polymerization of 6 with differing numbers of silanol groups. On re-extraction with hot water the fragment size decreased. It is postulated that the network chain length of the three-dimensional polymer decreased as the interface was approached. At the glass surface a chemically bound molecular layer could be identified. The full chemical nature of the deposit is complicated by the incorporation of aluminium from the substrate into the coating. It was also possible to confirm that a layer of warm-water soluble oligomers existed at the air interface.