Design and synthesis of zero–zero-birefringence polymers in a quaternary copolymerization system

We designed and synthesized quaternary copolymers of methyl methacrylate (MMA), 2,2,2-trifluoroethyl methacrylate (TFEMA), benzyl methacrylate (BzMA), and 3,3,5-trimethylcyclohexyl methacrylate (TMCHMA) and we investigated their birefringence, thermal properties, and other optical properties. When the copolymer composition was MMA/TFEMA/BzMA/TMCHMA = 50:38:8:4, 40:30:7:23, or 30:21:7:42 (wt%), a zero–zero-birefringence polymer that exhibited neither orientational nor photoelastic birefringence was obtained. We demonstrated that such zero–zero-birefringence polymers with a variety of compositions could be successfully prepared in the quaternary system by using the same compensation method as applied in ternary random copolymerization. We also demonstrated that the glass-transition temperature (T_g) and refractive index (n_D) of these copolymers could be controlled with high accuracy while retaining their zero–zero-birefringence property. We can therefore predict the type of birefringence, the T_g, and the n_D of a particular copolymer before polymerization. Zero–zero-birefringence polymers with the most appropriate characteristics can then be synthesized selectively by quaternary copolymerization.     

Isotopomer analysis of production and consumption mechanisms of N2O and CH4 in an advanced wastewater treatment system

Wastewater treatment processes are believed to be anthropogenic sources of nitrous oxide (N(2)O) and methane (CH(4)). However, few studies have examined the mechanisms and controlling factors in production of these greenhouse gases in complex bacterial systems. To elucidate production and consumption mechanisms of N(2)O and CH(4) in microbial consortia during wastewater treatment and to characterize human waste sources, we measured their concentrations and isotopomer ratios (elemental isotope ratios and site-specific N isotope ratios in asymmetric molecules of NNO) in water and gas samples collected by an advanced treatment system in Tokyo. Although the estimated emissions of N(2)O and CH(4) from the system were found to be lower than those from the typical treatment systems reported before, water in biological reaction tanks was supersaturated with both gases. The concentration of N(2)O, produced mainly by nitrifier-denitrification as indicated by isotopomer ratios, was highest in the oxic tank (ca. 4000% saturation). The dissolved CH(4) concentration was highest in in-flow water (ca. 3000% saturation). It decreased gradually during treatment. Its carbon isotope ratio indicated that the decrease resulted from bacterial CH(4) oxidation and that microbial CH(4) production can occur in anaerobic and settling tanks.     

Tunable separation of single-walled carbon nanotubes by dual-surfactant density gradient ultracentrifugation

We present a systematic study of the effects of surfactants in the separation of single-walled carbon nanotubes (SWNTs) by density gradient ultracentrifugation (DGU). Through analysis of the buoyant densities, layer positions, and optical absorbance spectra of SWNT separation using the bile salt sodium deoxycholate (DOC) and the anionic salt sodium dodecyl sulfate (SDS), we clarify the roles and interactions of these two surfactants in yielding different DGU outcomes. The separation mechanism described here can also help in designing new DGU experiments by qualitatively predicting outcomes of different starting recipes, improving the efficacy of DGU and simplifying post-DGU fractionation.      

Fabrication of discrete polystyrene nanoparticle arrays with controllable their structural parameters

We have demonstrated the fabrication of two-dimensionally periodic non-close packed arrays of spherical polystyrene nanoparticles with controllable their structural parameters including diameter and interpartcile distance. The principle of this procedure relies on stepwise integration of spin-coat-assisted colloidal self-assembly of the single layer of close-packed polystyrene nanoparticle on a substrate, and subsequent etching of the particle under atmospheric pressure helium plasma. The plasma process converted the close-packed nanoparticle array into non-close-packed arrangement remaining with unchanged their original spherical shape and periodicity. Owing to the etching process underwent isotropically, the structural parameters could be controlled with nanometric accuracy by the treatment time. The etching rate strongly depended on the working pressure conditions, and the etching rate under 250 Torr was ca. 3 times faster than that of the 760 Torr. The effects of the working pressure indicated the neutral helium radicals and photons diffused from the plasma might be primarily responsible for the etching.     

A novel method to improve low‐voltage ride‐through capability of wind turbine generators

With increasing penetration of wind farms, power grids have responded by developing specific grid codes to maintain their stability. One of the main grid codes is the low‐voltage ride‐through (LVRT) capability, which requires the wind generator to remain connected when the grid voltage sags for a certain time period. A wind farm with squirrel cage induction generators suffers this LVRT problem the most because of their direct connection to the grid and reactive power consumption. In this paper, a new method is proposed to solve this problem by shunt‐connecting a motor‐driven mechanical load to the cage wind generator. For driving mechanical loads, the induction motor is most widely used in industries. This paper studies the terminal voltage holding effect of an induction machine during grid voltage sag due to the magnetic flux holding effect and the saturation characteristic. Taking advantage of this effect, the induction motor that is used for driving mechanical load is then proposed to improve the LVRT capability of wind turbine generators. Furthermore, the change of the rotating speed or slip of the induction machine is found to have a great impact on improving the LVRT. By adding some inertia to the motor‐driven mechanical load, an enhanced voltage holding effect, and therefore LVRT improvement, is expected for the wind farm. Both simulation and experimental results prove the effectiveness of the proposed method. © 2013 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Flow fields with vortex in a small semi-open axial fan

In order to clarify the effect of tip clearance (TC) size on fan performance and the flow field at rotor outlet in a small semi-open axial fan, the experimental investigation was carried out. The tip diameter of test fan rotor was 180mm and test TC sizes were 1mm (TC=1mm) and 4mm (TC=4mm). Fan characteristics tests were carried out for two cases of TC size and three-dimensional velocity fields at rotor outlet were measured using a single slant hot-wire probe at four flow-rate conditions. As a result, it was found that the pressure — flow-rate characteristics curves for two cases showed almost the same tendency. However, the ensemble averaged velocity profiles along radial measurement stations of TC=4mm largely changed compared with that of TC=1mm in cases of small flow-rate condition. From the phase-locked averaging results, it was also found that the vortex existed in the rotor outlet flow field of high flow-rate condition for each TC case. Compared with the vortices for TC=1mm and TC=4mm, the vortex for TC=4mm was stronger than that for TC=1mm.     

The Effects of Conventional Stabilizers and Phenol Compounds Used as Antioxidants on the Stabilization of Nitrocellulose

The thermal behavior of nitrocellulose (NC) containing diphenylamine (DPA), 2‐nitrodiphenylamine (2‐NO₂‐DPA), N‐nitrosodiphenylamine (N‐NO‐DPA), ethyl centralite (EC), akardite II (AKII), 1,1,3‐tri‐(2‐methyl‐4‐hydroxy‐5‐tert‐butyl‐phenyl)‐butane (BP_less), 3‐(3,5‐di‐tert‐butyl‐4‐hydroxy‐phenyl)‐propionic acid octadecyl ester (BP_hin), and 3‐(3‐tert‐butyl‐4‐hydroxy‐5‐methyl‐phenyl)‐propionic acid 2‐(9‐{2‐[3‐(3‐tert‐butyl‐4‐hydroxy‐5‐methyl‐phenyl)‐propionyloxy]‐1,1‐dimethyl‐ethyl}‐2,4,8,10‐tetraoxa‐spiro [5.5] undec‐3‐yl)‐2‐methyl‐propyl ester (BP_semi) was observed during isothermal storage at 393 K using a C80 microcalorimeter. The results indicate that each stabilizer decreased NC's maximum heat release rate and increased the induction period of heat release. We also observed that the maximum heat release rate and the induction period were dependent on the amount of stabilizer. DPA decreased the maximum heat release rate to the greatest extent, with the other stabilizers having similar effects on the decrease of maximum heat release rate. AKII prolonged the induction period of heat release most. The order of prolongation of the induction period was AKII>2‐NO₂‐DPA≈DPA>N‐NO‐DPA≈EC>BP_less≈BP_semi≈BP_hin.     

Partial oxidation of n-hexadecane and polyethylene in supercritical water

In this study, we show the results of partial oxidation experiments of n-hexadecane (n-C₁₆) and polyethylene (PE) in supercritical water (SCW). The experiments were carried out at 673 or 693 K of reaction temperature and 5 or 30 min of reaction time using a 6 cm³ of a batch type reactor. Water density ranged from 0.1 to 0.52 g/cm³ (water pressure: 20–40 MPa). The loaded amount of oxygen was set to 0.3 of the ratio of oxygen atom to carbon atom. Some experiments were made using CO instead of oxygen for the partial oxidation of n-C₁₆ and PE to explore the effect of water gas shift reaction. In the results of partial oxidation of n-C₁₆, the yield of CO and some compounds containing oxygen atoms, such as aldehydes and ketones increased with increasing water density. Moreover, 1-alkene/ n-alkane ratio in the products decreased with increasing water density. The 1-alkene/n-alkane ratio was lower than that of pyrolysis in SCW. Also for the case of PE experiments, in dense SCW (0.42 g/cm³), the 1-alkene/n-alkane ratio in partial oxidation was lower than that in SCW pyrolysis. In the case of CO experiments for n-C₁₆ and PE, 1-alkene/n-alkane ratio was a little lower than that of pyrolysis in SCW. These results show that the yield of n-alkane, which is a hydrogenated compound, was higher through water gas shift reaction in SCW and also through partial oxidation in SCW. Therefore, these results suggest the possibility of hydrogenation of hydrocarbon through partial oxidation followed by the water gas shift reaction.     

Features of Rotating Stall Cell in a Diagonal Flow Fan（in Case of Mid-loading Rotor）

The structure and behavior of rotating stall cell were experimentally clarified in a diagonal flow fan. The specific-speed of the fan was 1140 (r/min, m3/min, m), and the total pressure-rise coefficient at design flow-rate was 0.345. The static pressure on outer casing wall and the total pressure at rotor inlet and outlet were measured using a high response pressure transducer. The measured data were processed by the use of DPLA technique, and the structure and behavior of rotating stall cell were obtained. As a result, the stall cell extent for circumferential and spanwise direction and the pressure distributions inside stall cell were clarified. The details of stall cell propagation were also shown.     

Synthesis of highly crystalline hexagonal cesium tungsten bronze nanoparticles by flame-assisted spray pyrolysis

Highly crystalline and hexagonal single-phase cesium tungsten bronze (Cs_0.32WO₃) nanoparticles were successfully synthesized by a flame-assisted spray pyrolysis followed by annealing under a reducing gas atmosphere. The resulting Cs_0.32WO₃ nanoparticles featured a pure hexagonal Cs_0.32WO₃ phase with a high crystallinity and homogeneous chemical composition. Unlike conventional methods, the proposed process in this paper has several advantages, including a short reaction time and the ability to yield products with high purity and good energy efficiency. Furthermore, the Cs_0.32WO₃ nanoparticles produced in this research showed a remarkable near-infrared shielding ability with a 97.7% cut-off at 1500?nm.