Analytical Model for Redistribution Profile of Ion-Implanted Impurities During Solid-Phase Epitaxy

We evaluated the redistribution profiles of ion-implanted impurities during solid-phase epitaxy using Rutherford backscattering spectrometry (RBS). RBS data revealed that the As concentration changes only near the moving amorphous/crystal interface. We derived an analytical model for the redistribution profiles using a segregation coefficient m between amorphous and crystalline Si, introduced a parameter of reaction length l that is the distance where impurities were exchanged, and obtained good agreement with experimental data with an m value of 3 and an l value of 1 nm for As. Furthermore, we applied our model to P and B redistribution profiles and obtained good agreement with corresponding m value of 4 and l value of 1 nm for P and m value of 0.3 and l value of 1 nm for B     

Low-Force Electric Contact Processes on Cu Electrodes

A contact process between large-scale integration (LSI) pads and test probes at low contact force is a key to developing a probe card with smaller pitch and higher pin count. In this paper, we report on the characteristics of low-force contact methods on Cu electrodes. One is the fritting process, in which an electric breakdown is utilized to break the surface oxide, and the other is the heating treatment in hydrogen gas aimed at deoxidizing the surface Cu oxide. Conventional tungsten needle probes were used as testing probes, and contact resistances at low contact force of 1-5 mN were measured. Contact resistances smaller than 1 Omega were obtained by the fritting processes, in which the voltage and the current were 10 V and 280-320 mA, respectively. A deoxidization process at over 260degC was found to be effective for decreasing the contact resistance. The X-ray photoelectron spectroscopy (XPS) was utilized to investigate the surface state of hydrogen-treated Cu, and the deoxidization of Cu₂O to Cu was observed in samples treated at 260degC, while no change was found in that at 150degC.     

Steady-State Characteristics of a Current-Source Inverter/Double-Wound Synchronous Machine System for AC Power Supply

A detailed steady-state analysis of a novel dc-to-ac conversion system used as an ac power source in dc electric railway coaches is presented. This system consists of a current-source inverter, a double-wound synchronous machine, a position sensor, and a control circuit. An equivalent circuit convenient for predicting the steady-state behavior of the system is first derived. Based on this equivalent circuit, the output voltage waveforms are then examined. It is shown that the voltage waveforms are nearly sinusoidal except that narrow spikes are superposed on them during commutation of the thyristors. As to armature reaction in the double-wound synchronous machine, it is shown that a remarkable direct reaction appears which affects the voltage regulation of the system. Finally, a method for keeping the output voltage and frequency constant is discussed.     

Fabrication of Nanocomposite Ceramics by Crystallization of Rapidly Solidified Eutectic Melts

Eutectic melt solidification is shown to avoid cracking during solidification by quenching an amorphous phase. Subsequent annealing results in micro/nanostructure ceramics. This strategy has been applied to HfO₂–Al₂O₃–GdAlO₃ and Y₂O₃–CaO–Al₂O₃ ternary systems that have deep eutectics. In most cases, ceramic materials cracks when they are solidified from melt due to the thermal stress accumulated on the grain boundaries, the large specific volume difference between the melt and the crystalline solid, etc. The main reason why this strategy works is that a eutectic composition yields an amorphous phase from the melts by rapid cooling and the amorphous phase enables to design crystallization without cracking by postannealing. Appropriate postannealing for the quenched amorphous enables to control the crystallization behavior from the amorphous phase, which yields nanostructured composites without cracking. For the HfO₂–Al₂O₃–GdAlO₃ case, the melt solidification and postannealing yields a nanocomposite with high transparency due to reduced scattering of 5–10 nm crystallites. For the Y₂O₃–CaO–Al₂O₃ case, a plate-shaped bulk composite is obtained without cracking by molding the melt and postannealing.     

Interfacial area concentration in bubbly flow

Interfacial area concentration is one of the most important parameters in two-phase flow. It is related to mass, momentum and energy transfer at the interface. In bubbly flow, it has close relation to bubble diameter. Interfacial area concentration was measured with particular attention to bubble diameter at inlet. The relationship between bubble diameter and interfacial area was theoretically considered. The possibilities of measurement methods of interfacial area concentration with multiprobes were discussed and a preliminary experiment for one of these methods was carried out.     

A novel method for induction and detection of anaphylactic reaction using the mouse abdominal wall (AW method)

We found that an antigen-specific anaphylaxis was induced by antigen challenge to the abdominal wall, ear auricle, or subcutaneous tissue in mice sensitized 9 days previously with antigen and adjuvant. The anaphylactic reaction was detected by vascular permeability at the injected site 7 minutes after challenge, which was the best time for estimation. A novel method (AW method) for induction and detection of the anaphylactic reaction in mice was established using the abdominal wall as the challenge site. This method could detect the anaphylactic response in mice 1 to 3 weeks after sensitization. The increase in vascular permeability was completely inhibited by administration of diphenhydramine.     

Water-soluble polyion complex associates of DNA and poly(ethylene glycol)-poly(L-lysine) block copolymer

Complex formation of poly(ethylene glycol)-poly(L-lysine) (PEG-PLL) AB type block copolymer with salmon testes DNA or Col E1 plasmid DNA in aqueous milieu was studied. The PLL segment of PEG-PLL interacts with nucleic acid through an electrostatic force to form a water-soluble complex associate with a diameter of ca. 50 nm. PEG segments surrounding the core of the polyion complex prevented the complex from precipitation even under stoichiometric conditions, at which the unit ratio of L-lysine in PEG-PLL and phosphate in the DNA is equal. The profile of the thermal melting curve revealed a higher stabilization of DNA structure in PEG-PLL/DNA complexes compared to that in the complex made from DNA and PLL homopolymer with the same molecular weight as the PLL segment in PEG-PLL. This stabilizing effect on the DNA structure may be due to the compartmentalization of DNA into the microenvironment of PEG with low permittivity. The reversible nature of the PEG-PLL/DNA complex was further verified through the addition of polyanion [poly-(L-aspartic acid)]: Poly(L-aspartic acid) replaced DNA in the complex with PEG-PLL, resulting in the release of free DNA in the medium. Furthermore, the PEG-PLL/DNA complex showed high resistance against DNase I attack, suggesting DNA protection through the segregation into the core of the associate having PEG palisade.     

Optimal periodic maintenance strategy under an intermittently used environment

In this paper, the optimal periodic replacement-like strategy with minimal repairs is considered under an intermittently used environment. Suppose that transactions or jobs with exponential service times arrive at a system according to a homogeneous Poisson process and the system is alternatively in either a busy or an idle period subject to demand for use. We derive approximately the optimal preventive maintenance schedule which minimizes the relevant expected cost criterion for the system which behaves intermittently on an M/M/1 queueing process, and compare it with the usual maintenance schedule for the continuously used system.     

Transport of direct dye into cellulose membrane

The dyeing process for a cellulose membrane–direct dye system is analyzed based on a parallel transport mechanism of surface and pore diffusion with Freundlich isotherm. Numerical solutions were obtained in order to clarify how the surface and pore diffusion resistances affect the uptake curve. The numerical solutions were also compared with an analytical solution for surface diffusion control to establish the range where the analytical solution can be considered as an acceptable approximation. The uptake curves in the cellulose membrane-chromophore (C.I. Direct Yellow 12) system in the presence of inorganic electrolyte were measured. The rate of adsorption and the maximum amount of adsorption increased with an increase in the concentration of those electrolytes. The rate of adsorption was approximately controlled by the surface diffusion rather than by pore diffusion. The surface diffusivities of the dye were little affected by either the concentration and or nature of the electrolyte.     

A new blood compatible and permselective hollow fiber membrane for hemodialysis

The authors have prepared a blood compatible and highly permselective hemodialysis membrane composed of polyether segmented nylon. This block copolymer was synthesized by polycondensation of bis-3-aminopropyl-poly(tetramethylene oxide) (PTMO) and poly(imino-1,3-bismethyl-cyclohexyl-iminoisophtharoyl) (NyBl) prepolymer obtained by polycondensation of 1,3-bis(aminomethyl)cyclohexane (B) and isophthalic acid (I). The molecular weight (MW) calculated from the number of end-groups was 16,000-21,000. In vitro blood compatibility was evaluated in terms of platelet adhesion onto the surface. PTMO-NyBl surfaces showed excellent platelet adhesion preventing properties. The PTMO-NyBl hollow fiber membrane was obtained by a dry-wet spinning process. The membranes had higher permeability coefficients for macromolecules ranging from MW 10,000 to 20,000 than polysulfone hollow fiber membrane (PS membrane), and had acceptably low albumin permeability for use as a dialysis membrane. The ex vivo blood compatibilities of PTMO-NyBl membrane and PS membrane were investigated by extracorporeal circulation in a pig model. The PTMO-NyBl membrane gave excellent results when assessing hemodialysis leukopenia, oxidative burst, and free platelet count decrease.