Effect of vanadium and chromium on the microstructural features of V–Cr–Mn–Ni spheroidal carbide cast irons

The objective of this investigation is to study the influence of vanadium（5.0wt%–10.0wt%） and chromium（0–9.0wt%） on the microstructure and hardness of Cr-V-Mn-Ni white cast irons with spheroidal vanadium carbides. The alloys＇ microstructural features are presented and discussed with regard to the distribution of phase elements. The structural constituents of the alloys are spheroidal VC, proeutectoid cementite, ledeburite eutectic, rosette-shaped carbide eutectic（based on M7C3）, pearlite, martensite, and austenite. Their combinations and area fraction（AF） ratios are reported to be influenced by the alloys＇ chemical composition. Spheroidized VC particles are found to be sites for the nucleation of carbide eutectics. Cr and V are shown to substitute each other in the VC and M7C3 carbides, respectively. Chromium alloying leads to the formation of a eutectic（γ-Fe ＋ М7С3）, preventing the appearance of proeutectoid cementite in the structure. Vanadium and chromium are revealed to increase the total carbide fraction and the amount of austenite in the matrix. Cr is observed to play a key role in controlling the metallic matrix microstructure.     

Mechanisms of neuronal calcium homeostasis destabilization caused by hyperstimulation of glutamate receptors

The present paper summarizes the data obtained in studying the mechanisms of glutamate-induced deterioration of neuronal Ca2+ homeostasis. In the cultured mammalian central neurons, a short-term (< 1 min) glutamate (GLU, 100 mu) challenge is known to induce a readily reversible (transient) neuronal [Ca2+]i increase. In contrast, a long-term (15-30 min) GLU exposure leads to the appearance of high [Ca2+]i plateau or to the partial recovery of the increased [Ca2+]i. Experiments show that impaired [Ca2+]i recovery in the postglutamate period cannot be explained by the increased [Ca2+]i permeability of the neuronal membrane, as earlier considered. Moreover, a sustained elevation of [Ca2+]i during and after chronic GLU application is associated with a progressive decrease in Ca2+ permeability. The major cause of GLU-induced Ca2+ overload is the mitochondrial depolarization resulted from excessive Ca2+ influx into the mitochondria, the generation of free radicals and the opening of a "giant pore" in the inner mitochondrial membrane. This in turn suppresses both ATP synthesis and Ca2+ electrophoretic uptake into the mitochondrial matrix. In combination with [Ca2+]i-dependent acidification, this leads to the suppression of Ca2+ release from the cell via Na+/Ca2+ exchanger and Ca2+/H+ pump of the neuronal membrane. Therefore, [Ca2+]i recovery following a long-term GLU treatment becomes strongly or even irreversibly compromised.     

Managing complex orthodontic problems: the use of implants for anchorage

In congestive heart failure captopril modifies the left ventricular filling pattern mainly by unloading the heart. We investigated whether the structural characteristics of the left ventricle may influence the acute effects of captopril on this pattern in patients with untreated hypertensive (H group, 6 patients) or idiopathic (I group, 14 patients) cardiomyopathy. We evaluated changes of pulsed Doppler mitral flow, of systemic arterial and wedge pulmonary pressures 40 min after 25 mg captopril administered sublingually, and correlated these changes with the M-mode echocardiographic relative wall thickness index (h/r). Baseline mean arterial pressure (H = 137 +/- 20 mm Hg, mean +/- SD, I = 95 +/- 19 mm Hg; p < 0.001), and h/r (H = 0.38 +/- 0.03, I = 0.28 +/- 0.09; p < 0.05) were greater in the high blood pressure group; wedge pressure, echocardiographic biplane ejection fraction, and Doppler indexes of the left ventricular filling were similar in the two populations. After captopril, ejection fraction did not change significantly, mean arterial pressure decreased significantly in hypertensive patients (H group, baseline = 137 +/- 20, captopril = 119 +/- 10, p = 0.02; I group, baseline = 95 +/- 19, captopril = 90 +/- 24, p = nonsignificant), and the wedge pressure was reduced by the same extent in both groups (H group, baseline = 27.7 +/- 3, captopril = 21 +/- 7, p < 0.05; I group, baseline = 20 +/- 12, captopril = 15 +/- 8, p < 0.05). In the H group early mitral flow increased [(E wave integral) x (mitral annulus area)] by 38 +/- 15%, and was almost steady in the I group (-1.3 +/- 30%; group H vs. I = p < 0.01); late mitral flow [(A wave integral) x (mitral annulus area)] showed a pattern exactly opposite to this (H = +0.4 +/- 40%, I = +38 +/- 19; p < 0.01). In the whole population there was a significant correlation between the early/late flow ratio variations and baseline h/r (r = 0.6, p < 0.05). In chronic congestive heart failure, changes in left ventricular filling with captopril are related to h/r: a higher index, as recorded in the H group, is associated with "true normalization' of the filling pattern after captopril; a lower index, as recorded in the I group, is associated with "pseudonormalization' despite a similar decrease of left ventricular filling pressure.     

Automatic control system for a pipe’s inner surface coating

Theoretical bases for controlling the application of coatings to the inner surface of pipes and other hollow products are considered based on the stabilization of the velocity of the coating material in the product cavity taking into account temperature and viscosity. The device makes it possible to automatically compensate for the variation in the coating thickness depending on temperature taking into account the characteristics of the used control equipment. The dependence of the coating thickness on temperature and material velocity is described. The system that implements the proposed method in the MATLAB + SIMULINK shell is simulated. The optimal values of the system gain and level sensor sensitivity that minimize the dynamic error of the control system are determined.     

Diagnostics of degradation processes induced by pulsed electric signals at the aluminum-silicon interface

Thermal conditions in an aluminum metallization stripe deposited onto a single crystal silicon substrate have been studied during the passage of single rectangular electric pulse with a current density of j < 8 × 10¹⁰ A/m² and a duration of τ = 100–1000 μs. Based on the results of this analysis, a method of diagnostics of the state of metallization contact systems and determination of the conditions of their safe operation is proposed.     

Local effects in the vicinity of inserts in sandwich panels

The paper considers local bending effects induced in the vicinity of inserts in sandwich panels. Such local bending effects are associated with an increase of bending stresses in the sandwich faces and normal and shear stresses in the sandwich core. An earlier developed analytic model [Proceedings of the Sixth International Conference on Sandwich Structures (ICSS-6) (2002) 551] is adapted for the case of a sandwich panel with circular insert, with elastic properties differing from those of the core. The locally induced stresses in the faces and core due to presence of the insert are expressed via simple analytic relations (and charts) enabling an estimation of these local stresses. Finite element analysis is employed to demonstrate the applicability of the analytic model, and a good correspondence between the numerical and the analytical data is found. A study case related to marine applications, namely a circular insert in a sandwich deck panel used for mounting of a rigging fixture, is considered, and optimization of an existing design is carried out.     

Experience gained with development of the instrumentation and control system for the PGU-410 power unit at the Krasnodar cogeneration station on the basis of the tornado-n distributed control system

The development of the instrumentation and control system for the PGU-410 power unit at the Krasnodar cogeneration station is discussed. Problems encountered in designing the process control system of a complex facility are considered, in particular, the need to integrate local control systems. Special attention is paid to the importance of setting up a united control area at such facilities.     

Problems of Kinematic Analysis and Special Positions of Mechanisms of Robots with Parallel Structure

A solution to the problem of the velocities and problems of analysis of the special positions of the spatial mechanisms with parallel structure with a kinematic decoupling is considered. The Gosselin and Angeles method of partial derivatives and the apparatus of the theory of screws is used.