Effects of brefeldin-A on Golgi morphology in human cultured fibroblasts observed in three-dimensional stereo scanning electron microscopy

Brefeldin A (BFA) has been reported to cause disassembly of the Golgi. We have used three-dimensional (3-D) high-resolution scanning electron microscopy (HRSEM) to investigate these effects in human skin fibroblast cells. The spontaneous reassembly during prolonged exposure to BFA and some effects of forskolin were observed. A BFA concentration of 5μg/ml caused Golgi complexes to become vesicular, resulting in a progressive decrease in the size of the Golgi. Morphologic changes were visible within 2 min of BFA incubation, and by 30 min no identifiable Golgi could be found. Spontaneous reassembly of the Golgi apparatus upon the removal of the BFA or with continued long-term exposure with BFA could not be confirmed. Preliminary experiments with forskolin were not effective in reversing or inhibiting the effects of BFA in human fibroblast cells grown in culture. This inability for spontaneous reassembly and nonreversal by forskolin may reflect a differential effect of BFA in various cell types. HRSEM has proven to be useful for observing 3-D morphologic effects of BFA in Golgi.     

An analytical model for high electron mobility transistors

In this paper we present a new model for HEMT's which is based on a single analytical function that describes the electron concentrations in the two dimensional electron gas and in the AlGaAs layer. Besides accounting for the AlGaAs conduction, the model includes the effect of mobility degradation, channel length modulation in the saturation region and the series resistances R_S and R_D. The model results in closed form expressions for the current, transconductance, output conductance and gate capacitance. Finally, the theoretical predictions of the model are compared with the experimental data and shown to be in good agreement over a wide range of bias conditions     

On-line dead-time compensation method using disturbance observer

A new on-line dead-time compensation method for a permanent magnet (PM) synchronous motor drive is proposed. Using a simple disturbance observer without any additional circuit and off-line experimental measurement, disturbance voltages in the rotor reference dq frame caused by the dead time and nonideal switching characteristics of power devices are estimated in an on-line manner and fed to voltage references in order to compensate the dead-time effects. The proposed method is applied to a PM synchronous motor drive system and implemented by using software of a digital signal processor (DSP) TMS320C31. Simulations and experiments are carried out for this system and the results well demonstrate the effectiveness of the proposed method.     

Over GHz electrical circuit model of a high-density multiple line grid array (MLGA) interposer

The multiple line grid array (MLGA) interposer was recently introduced as a future high-density high-speed bonding method. In this paper, we introduce an electrical model and high-frequency characteristics of the MLGA interposer. The high-frequency electrical model was extracted from microwave S-parameter measurements up to 20 GHz as well as from fundamental microwave network analysis. For the parameter fitting process during model extraction, an optimization method was used. Several different types of MLGA interposers were designed, assembled and tested. The test vehicles contained coplanar waveguides, probing pads and an MLGA interposer structure. The height of the MLGA, the conductor shape inside the MLGA, and the dielectric insulator of the MLGA were varied. From the model, an MLGA with a height of 0.4 mm and a polymer dielectric insulator was found to have 203 pH of self inductance, 49 pH of mutual inductance with the nearest ground conductor line, and 186 fF of mutual capacitance. By reducing the height of the MLGA and by using an insulator with a lower dielectric constant, parasitic inductance and capacitance is further reduced. TDR/TDT simulation and measurement showed the validity of the extracted model parameters of the MLGA interposer. Circuit simulation based on the extracted model revealed that the MLGA interposer could be successfully used for microwave device packages up to 20 GHz and for high-speed digital device packages with a clock cycle up to 5 GHz.     

Effects of potential and heat treatment on phase transition of alumina dielectric layer

The characteristics and growth behaviors of alumina dielectric layer formed by anodic oxidation were investigated. The aluminum oxide layer anodized at 400 V was predominantly amorphous alumina, but at the applied potentials more than 500 V, amorphous and crystalline γ-alumina were existed in anodic oxide layer and the ratio of γ-alumina increased with the increasing applied potential. During the heat treatment at 600^°C or higher temperature, amorphous alumina layer was transformed into the crystalline γ-alumina. The phase transition of anodic amorphous alumina into crystalline depends on anodic applied potentials and heat-treatment temperatures.     

Nanoporous activated carbon cloth for capacitive deionization of aqueous solution

Activated nanostructured-carbon cloths with a high ratio of surface area to volume are used as electrode for capacitive deionization. The electrochemical properties on capacitive deionization for NaCl solution have been investigated to improve efficiency of capacitive deionization properties from aqueous solution, employing chemical surface-modification by etching in alkaline and acidic solution. The removal efficiency of inorganic salts of activated carbon cloths by chemical modification significantly increased. Specially the carbon cloth surface modified in HNO₃ showed an effect of improvement in the CDI efficiency due to not only ion adsorption by an electric double layer, but also electron transfer by Faradaic reaction.     

Analysis of hazard area associated with hydrogen gas transmission pipelines

Hydrogen is considered to be the most important future energy carrier in many applications reducing significantly greenhouse gas emissions, but the safety issues associated with hydrogen applications need to be investigated and fully understood to be applicable as the carrier. Generally, the locations of hydrogen production and consumption are different. Hydrogen must be transported from the point of production to the point of use. Pipeline delivery is cheaper than all other methods for large quantities of hydrogen. The rupture of a hydrogen pipeline can lead to outcomes that can pose a significant threat to people and property in the immediate vicinity of the failure point. In this work, a simplified equation of hazard analysis is proposed for the pipeline transporting hydrogen, which relates the diameter, the operating pressure and the length of the pipeline to the size of the affected area in the event of a failure of the pipeline. The dominant hazards are thermal radiation from sustained fire and shock pressure from gas cloud explosion. For a transmission pipeline of hydrogen gas, the hazard area from the fire is slightly larger than by the other event. The hazard area is directly proportional to the operating pressure raised to the power one-half, and to the pipeline diameter. This simplified equation to estimate the hazard area will be a useful tool for safety management of hydrogen gas transmission pipelines.     

Photodegradation mechanism and stabilization of polyphenylene oxide and rigid‐rod polymers

Poly(2,4‐dimethyl‐1,4‐phenylene oxide) (PPO), poly(benzo[1,2‐d:5,4‐d′]bisoxazole‐2,6‐diyl‐1,4‐phenylene) (PBO) and poly(benzo[1,2‐d:4,5‐d′]bisthiazole‐2,6‐diyl‐1,4‐phenylene) (PBZT), which are polymers with extended conjugated structures, undergo a self‐sensitized photo‐induced electron‐transfer reaction. A second component is not required. This article presents many similar observations on these polymers when they are exposed to light and evidence to support the proposed photo‐induced electron‐transfer mechanism. Methods to stabilize these polymers against photo‐oxidation are also described. Workers investigating other conjugated polymeric systems may find the experimental methods, observations and polymer stabilization approaches discussed in this review useful. Copyright © 2005 Society of Chemical Industry     

Transluminal balloon angioplasty, stents, and atherectomy

Arterial bypass grafting for occlusive disease is still considered the gold standard in the treatment of arterial occlusive disease. However, less invasive methods are available for select patients. Percutaneous balloon angioplasty has been shown to be effective in focal iliac artery stenosis, with patency rates of 50% to 90% at 5 years. Patency rates for femoropopliteal lesions are generally less than 50% at 2 years. Complications seen with balloon angioplasty often can be treated with arterial stents. Stents can be categorized into balloon-expandable, which provide a rigid scaffold to support the artery, self-expanding, which exert radial force to resist external compression, and thermal expanding stents, which allow for the use of a smaller introducer sheath. Another treatment option is atherectomy, in which the offending lesion is removed instead of fracturing and dilating the lumen. Although overall initial results of atherectomy have not been favorable, short lesions with eccentric atheroma or intimal hyperplasia, such as those seen in dialysis access fistulas or vein graft stenoses, may respond well.