Numerical analysis of the warpage problem in TSOP

The reliability and the solderability of thin small outline package (TSOP) are significantly affected by the warpage that is generated after epoxy molding compound (EMC) molding process. This warpage problem mainly results from the mismatch of material properties such as Young's modulus, Poisson's ratio and coefficient of thermal expansion (CTE) and the geometric structure of each component for TSOP. The optimization of both material properties and geometric structures using the numerical analysis is necessary to reduce the warpage of TSOP. However, there are still some limitations for the numerical analysis to obtain proper results consistent with the practical warpage values. In this paper, the numerical analysis is performed under the assumption of elastic behavior for EMC. Furthermore, to solve the limitations, the material properties at the molding temperature and the degree of reaction rate at the end of the molding process of EMC are considered together for the analysis. This numerical analysis gives the higher warpage values than the measured ones, and is applicable to the practical design of the reliable electronic package.     

Structural properties of 0.65Pb(Mg1/3Nb2/3)O3–0.35PbTiO3 relaxor ferroelectric thin films on SrRuO3 conducting oxides

Coating of 0.65Pb(Mg_1/3Nb_2/3)O₃–0.35PbTiO₃ (PMN–PT) relaxor ferroelectrics by a sol–gel method is followed by growth of epitaxial SrRuO₃ (SRO) metallic oxide electrodes on SrTiO₃ (STO) single-crystal substrate by pulsed laser deposition. High-quality PMN–PT films on SRO with preferred growth orientation were successfully fabricated by controlling the operation parameters. Structural properties of relaxor ferroelectric PMN–PT thin films on SRO/STO substrates have been studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and atomic force microscopy (AFM). In-plane and out-of-plane alignments of the heterostructure are confirmed and the structural twinning of the materials are also revealed.     

Photodegradation mechanism and stabilization of polyphenylene oxide and rigid‐rod polymers

Poly(2,4‐dimethyl‐1,4‐phenylene oxide) (PPO), poly(benzo[1,2‐d:5,4‐d′]bisoxazole‐2,6‐diyl‐1,4‐phenylene) (PBO) and poly(benzo[1,2‐d:4,5‐d′]bisthiazole‐2,6‐diyl‐1,4‐phenylene) (PBZT), which are polymers with extended conjugated structures, undergo a self‐sensitized photo‐induced electron‐transfer reaction. A second component is not required. This article presents many similar observations on these polymers when they are exposed to light and evidence to support the proposed photo‐induced electron‐transfer mechanism. Methods to stabilize these polymers against photo‐oxidation are also described. Workers investigating other conjugated polymeric systems may find the experimental methods, observations and polymer stabilization approaches discussed in this review useful. Copyright © 2005 Society of Chemical Industry     

Analysis on a mobile agent-based algorithm for network routing and management

Ant routing is a method for network routing in agent technology. Although its effectiveness and efficiency have been demonstrated and reported in the literature, its properties have not yet been well studied. This paper presents some preliminary analysis on an ant algorithm in regard to its population growing property and jumping behavior. Results conclude that as long as the value max, {i/spl Omega//sub j/|} is known, the practitioner is able to design the algorithm parameters, such as the number of agents being created for each request, k, and the maximum allowable number of jumps of an agent, in order to meet the network constraint.     

New approach to enhance adhesions between carbon nanotube emitters and substrate by the combination of electrophoresis and successive electroplating

Complementary electroplating combined with electrophoresis enhanced the field emission characteristics of emitters by improving the adhesions between CNT emitters and substrate. The emitting current of the CNT emitters prepared by our combined method increased nine times higher than that of CNT emitters prepared by electrophoresis only, since electroplating improved the adhesion of CNT emitters. During the life-time measurement for 10 h, the emitting current of CNT emitters fabricated by electrophoresis only was drastically decreased to 13% of the initial current, while that prepared by the combination of electrophoresis and successive electroplating decreased to 64% of the initial current. We suggest that our method is a promising approach for the efficient fabrication of reliable CNT emitters.     

Treatment of Natural Geometry in Finite Volume River Flow Computations

A method is proposed for the treatment of irregular bathymetry in one-dimensional finite volume computations of open-channel flow. The strategy adopted is based on a reformulation of the Saint-Venant equations. In contrast with the usual treatment of topography effects as source terms, the method accounts for slope and nonprismaticity by modifying the momentum flux. This makes it possible to precisely balance the hydrostatic pressure contributions associated with variations in valley geometry. The characteristic method is applied to the revised equations, yielding topographic corrections to the numerical fluxes of an upwind scheme. Further adaptations endow the scheme with an ability to capture transcritical sections and wetting fronts in channels of abrupt topography. To test the approach, the scheme is first applied to idealized benchmark problems. The method is then used to route a severe flood through a complex river system: the Tanshui in Northern Taiwan. Computational results compare favorably with gauge records. Discrepancies in water stage represent no more than a fraction of the magnitude of typical bathymetry variations.     

The effects of EPM long chain branching on TPO properties

In this paper the effects of EPM long chain branching are examined in terms of reheological, processing, and physical property responses in mechanically blended TPOs. Morphological effects induced by this polymer variable as indicated by SEM are detailed as well. The EPMs used in this study were produced by DSM Copolymer, Inc., in Baton Rouge, Louisiana.