Effect of P2O5 on the Nonisothermal Sinter‐Crystallization Process of a Lithium Aluminum Silicate Glass

Dense (~98.5%), lithium aluminum silicate glass‐ceramics were obtained via the sinter‐crystallization of glass particle compacts at relatively low temperatures, that is, 790–875°C. The effect of P₂O₅ on the glass‐ceramics' sinter‐crystallization behavior was evaluated. We found that P₂O₅ does not modify the surface crystallization mechanism but instead delays the crystallization kinetics, which facilitates viscous flow sintering. Our glass‐ceramics had virgilite (Li_xAl_xSi_3‐xO₆; 0.5 < x < 1), a crystal size <1 μm, and a linear thermal expansion coefficient of 2.1 × 10^?6°C^?1 in the temperature range 40–500°C. The overall heat treatment to obtain these GCs was quite short, at ~25 min.     

Maternal Flaxseed Oil During Lactation Enhances Bone Development in Male Rat Pups

Flaxseed oil is an alpha linolenic acid source important in the growth and body development stage; furthermore, this acid acts on adipose tissue and bone health. The aim of this study was to evaluate body composition, fatty acid composition, hormone profile, retroperitoneal adipocyte area and femur structure of pups at weaning, whose mothers were fed a diet containing flaxseed oil during lactation. After birth, pups were randomly assigned: control (C, n = 12) and flaxseed oil (FO, n = 12), rats whose mothers were treated with diet containing soybean or flaxseed oil. At 21 days, the pups were weaned and body mass, length, body composition, biochemical parameter, leptin, osteoprotegerin, osteocalcin, fatty acids composition, intra‐abdominal fat mass and femur structure were analyzed. FO showed (p < 0.05): higher body mass (+12 %) and length (+9 %); body fat mass (g, +45 %); bone mineral density (+8 %), bone mineral content (+55 %) and bone area (+35 %), osteocalcin (+173 %) and osteoprotegerin (+183 %). Arachidonic acid was lower (p < 0.0001), alpha‐linolenic and eicosapentaenoic were higher (p < 0.0001). Intra‐abdominal fat mass was higher (+25 %), however, the retroperitoneal adipocytes area was lower (?44 %). Femur mass (+10 %), distance between epiphyses (+4 %) and bone mineral density (+13 %) were higher. The study demonstrates that adequate flaxseed oil content during a lactation diet plays an important role in the development of pups.     

Color stability of denture shade tabs is affected by exposure to daylight and decontamination protocols

The purpose of this study was to investigate the effect of light exposure and decontamination protocols on the color stability of denture shade guide tabs. Fifty tabs for shades 62, 66, and 69 (Biotone IPN, Dentsply Sirona) were submitted to baseline L*a*b* measurements (EasyShade, Vita), separated into 5 experimental groups (n = 10), and subjected to one of the following conditions: G1–distilled water (DW‐H₂O)–control; G2 ?70% alcohol; G3–sodium hypochlorite 1% (NaClO); G4–no light exposure; G5–natural light exposure for 6 months. The experimental conditions were designed to simulate 6 months of clinical use. After the test period, final color measurements were recorded. The mean tristimulus coordinate difference (ΔL*,Δa*,Δb*) and total color difference values () were analyzed using 2‐way ANOVA and the Tukey test, α = .05. G2 (alcohol) produced less (P < .05) color change in shade 69 than G3 (NaClO). G5 (light exposure) affected the color stability for all shades, producing a statistical difference (P < .05) from G4 (no light exposure). It was concluded that natural light changes the color stability of the shade guides and that decontamination with 70% alcohol had the least impact on the color stability of the shade guide tabs.     

Evaluation of the effects of operational parameters in the pretreatment of sugarcane bagasse with diluted sulfuric acid using analysis of variance

The pretreatment of lignocellulosic residues has been extensively studied as a method to disrupt the cellulose–hemicelluloses–lignin complex in biomass to access the sugars in their respective components. In this work, we carried out a study using sulfuric acid pretreatment of sugarcane bagasse by varying the following operational parameters: solid loading (10–30% of bagasse relative to the volume of the sulfuric acid solution), sulfuric acid concentration (0.5–2.5% relative to the dry mass of bagasse), reaction time (5–25?min), and temperature (135–195°C). The obtained solids from each pretreatment condition were submitted to enzymatic hydrolysis under the same process conditions: 0.232?g of Celluclast 1.5?L and 0.052?g of Novozym 188 per g of pretreated sugarcane bagasse, 72?h of hydrolysis, and 200?rpm of agitation at 50°C. Using central composite rotational design configuration in the experiments and analysis of variance, the results indicate that the conditions that produced larger quantities of glucose by enzymatic hydrolysis (0.35?g glucose/g pulp) with minimum amounts of degradation products were as follows: 20% solids loading, 15?min of reaction time, 1.5% sulfuric acid, and a minimum temperature of reaction of 170°C.     

High surface area LaNiO<Subscript>3</Subscript> electrodes for oxygen electrocatalysis in alkaline media

LaNiO₃ coatings on nickel-foam supports were prepared by brush painting. The electrochemical properties were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Comparative studies were performed with LaNiO₃-pelleted electrodes. The roughness factors were determined by CV and found to be 5,208 ± 350 and 4,037 ± 250 for the pelleted and coated electrodes, respectively. EIS measurements confirm the results obtained by CV. Values lower than 0.3 were calculated for the morphology factors for both electrodes, indicating low electrochemical porosity. The experimental method used in this work to synthesise the oxide coupled with the use of Ni foam as support has proved to be very effective in producing oxide electrodes with surface areas higher than those referred to in relevant literature.     

Application of Multivariate Analysis in Mid-Infrared Spectroscopy as a Tool for the Evaluation of Waste Frying Oil Blends

Mid-infrared spectroscopy, in association with multivariate chemometric techniques, was employed for pattern recognition and the determination of the composition of waste frying oils (WFO); data are presented in terms of the percentage of soybean oil, palm oil and hydrogenated vegetable fat in frying oil blends. Principal component analysis (PCA) was performed using spectral data (3,000–600 cm⁻¹) to discriminate between the samples containing 100% soybean oil, 100% palm oil, 100% hydrogenated vegetable fat groups and their blends. Additionally, the results indicated that partial least squares (PLS) models based on mid-infrared spectra were suitable as practical analytical methods for predicting the oil contents in WFO blends. PLS models were validated by a representative prediction set, and the root mean square errors of prediction (RMSEP) were 2.8, 4.7 and 5.5% for palm oil, soybean oil and hydrogenated vegetable fat, respectively. The proposed methodology can be very useful for the rapid and low cost determination of waste frying oil composition while also aiding in decisions regarding the management of oil pretreatment and production routes for biodiesel production.     

Effect of alkylaluminum structure on Ziegler-Natta catalyst systems based on neodymium for producing high-cis polybutadiene

Summary  In this work, a laboratory scale process for producing polybutadiene with high content of cis-1,4 repeating units was studied. A Ziegler-Natta catalyst system constituted of neodymium versatate (catalyst), an alkylaluminum compound (alkylating agent and cocatalyst) and tert-butyl chloride (chlorinating agent) was used. The solvent employed was a mixture of hexane and cyclohexane (80/20 v/v). The objective of this work was to evaluate the effect of alkylaluminum structure and the influence of Al/Nd (5 to 15) molar ratio of long chain alkylaluminium compound (tri(n-hexyl)aluminum) on catalyst activity and polybutadiene characteristics. The alkylaluminum compounds employed in this study were tri(i-butyl)aluminum, tri(n-hexyl)aluminum, tri(n-octyl)aluminum and di(i-butyl)aluminum hydride. The polybutadienes molar masses obtained were strongly influenced by the alkylaluminum structure. Polymers with the highest molar masses were obtained when tri(i-butyl)aluminum, tri(n-hexyl)aluminum and tri(n-octyl)aluminum were employed. However, polymers with the highest contents of cis-1,4 units and the lowest molar masses were produced when di(i-butyl)aluminum hydride was employed.