Interactions of refractory materials with molten gasifier slags

The current study focuses on the analysis of sessile-drop interfacial reactions between two synthetic slags (based on average ash chemistries of coal and petcoke feedstock) and two refractory materials (90 wt% Cr₂O₃-10 wt% Al₂O₃ and 100 wt% Al₂O₃), using a Confocal Scanning Laser Microscope (CSLM). Ground slag samples (less than 325 mesh) were placed at specific microstructure locations on refractory substrates and heated to 1500 °C in an atmosphere of CO/CO₂ gas mixture (volume ratio = 1.8), using a gold-image heating chamber. Cross-sections of the slag/refractory interface indicated unique slag penetration into preferred areas of the refractory and grain dissolution into the slag which promoted spalling of the refractory. Initially, the slag attacked both grain boundaries and fine microstructure areas, freeing alumina grains into the slag. The formation of VO_x-based crystalline material in the petcoke slag was found to alter the liquid composition. Chemical spalling of Cr-containing crystal layer also facilitated degradation of the refractory.     

Probing Aromaticity of Borozene Through Optical and Dielectric Response: A Theoretical Study

In this work, we report electronic structure calculations aimed at computing the linear optical absorption spectrum and static dipole polarizablity of a newly proposed boron-based planar aromatic compound borozene (B ₁₂ H ₆). For the purpose, we use the semiempirical INDO model Hamiltonian, accompanied by large-scale correlation calculations using the multi-reference singles-doubles configuration-interaction (MRSDCI) approach. We present detailed predictions about the energetics, polarization properties, and the nature of many-particle states contributing to various peaks in the linear absorption spectrum. Our results can be used to characterize this material in future optical absorption experiments. We also argue that one can deduce the aromaticity of the cluster from the optical absorption and static polarizability results.     

Tuning the optical properties of metamaterials based on gold nanowire arrays embedded in alumina

We fabricated a series of gold nanowires/alumina composite films with different wire lengths. Optical transmission measurements confirmed that the composite films exhibit transverse and longitudinal surface plasmon resonances. We show that the wavelength of the longitudinal resonance is sensitive to nanowire length, while that of the transverse resonance is not. The experimental results are in agreement with the modeled results based on the Maxwell Garnett effective medium theory. Moreover, the window for negative refraction of the samples can be tuned in synchronism with the longitudinal resonance by the nanowire length.     

A non-linear regression form for vegetation index-crop yield relation incorporating acquisition date normalization

A non-linear form relating vegetation indices (VI) to crop grain yields which normalizes for differences in acquisition date is suggested. It is based on the assumption that deviations in VI near the peak VI follow a quadratic behaviour. This form gave a higher R2 value than a simple VI-yield linear model on a multi-year, multi-location data set of IRS (Indian Remote Sensing Satellite-1A) LISS-I(Linear Imaging Self Scanner-I) derived near-infrared (NIR)/red radiance ratios and wheat grain yields in a study site in Madhya Pradesh (India). As the suggested model includes time of peak as a variable, it allows integration of results from other sources, such as, weather-based crop phenology model or high repetivity spectral data into the VI-yield relation.     

EFFICIENT NEW SYNTHESES OF POLYCYCLIC AROMATIC HYDROCARBON ORTHO-QUINONES AND THEIR 2′-DEOXYRIBONUCLEOSIDE ADDUCTS

Three mechanisms have been proposed to explain the carcinogenic activities of polycyclic aromatic hydrocarbons (PAHs). On the basis of the nature of the active metabolites involved, they may be termed: the diol epoxide mechanism, the quinone mechanism, and the radical-cation mechanism. In connection with studies to evaluate the relative importance of these pathways, we required practical methods for the syntheses of the active PAH metabolites involved. We now report efficient new synthesis of the o-quinones of benzo[a]pyrene (BPQ), 7,12-dimethylbenz[a]anthracene (DMBAQ), and benz[a]anthracene (BAQ). These quinones are convenient synthetic precursors of the related o-catechols, trans-dihydrodiols, and diol epoxides, as well as the stable adducts of the o-quinones with 2-deoxyadenosine and 2′-deoxyguanosine.     

Low-Temperature Electrochemical Synthesis of ZrO2 Films on Zirconium Substrates: Deposition of Thick Amorphous Films and in situ Crystallization on Zirconium Anode

The feasibility of synthesizing crystalline ZrO₂ films at low temperatures was evaluated using an electrochemical method. Anodization of zirconium-metal substrates in tetraethyl ammonium hydroxide (TEAOH) solutions under constant applied voltage conditions at ∼25° and ∼100°C was investigated. The chemistry and microstructure of the anodic oxide films deposited on the zirconium-metal substrates under the above conditions were characterized using X-ray diffractometry and scanning electron microscopy. The results indicated that, with sufficiently high applied voltages (in the range of 300 V) at pH ∼9.5, the initial dissolution of the zirconium anode resulted in the local saturation of the electrolyte solution with Zr⁴⁺, forming Zr(OH)⁻₅, which deposited electrophoretically on the anode as a thick, gelatinous film at 25°C. Similar treatments at 100°C resulted in an in situ crystallization of Zr(OH)₄ gel to monoclinic ZrO₂.     

Surface studies on activated and hydrided CaNi5 alloy

X-ray photoelectron spectroscopic studies on the activated pure CaNi₅ alloy as well as the hydride formed at 1 atm pressure and room temperature, CaNi₅H_4.8, showed that on activation calcium segregates to the surface and forms the oxide, whereas most of the nickel on the surface is present in the metallic form. This indicates that the coexistance of the oxide phase and the metal phase is essential for the facile hydriding behaviour of CaNi₅.     

Copper losses and thermodynamic considerations in copper smelting

A relationship between copper in slag and copper in matte during copper sulfide smelting has been derived using industrial data from 42 plants employing blast furnaces, reverberatory furnaces, flash furnaces, and Mitsubishi smelting furnaces together with the available thermodynamic equilibrium data for Cu-Fe-S-O, FeO-SiO₂, and Cu-Fe-S systems and laboratory slag-matte equilibrium information. A copper smelting diagram showing oxygen potential; sulfur potential; and copper, magnetite, and sulfur contents in slag during the smelting of different grades of copper mattes is developed for mattes containing less than 70 pct copper. The data presented can be used to determine the entrained copper losses in slag. Further, by combining the calculated value of the entrained matte with the corresponding plant data for the sulfur content of the slag, it is possible to derive the dissolved sulfur content of the slag. These calculated values were in excellent agreement with the experimentally determined sulfide capacity of fayalite slags. It is shown that there is no need to assume the presence of dissolved copper sulfide species in industrial slags. The existing equilibrium data that relate the copper content of slags to oxygen potential adequately describe the copper losses in industrial slags.     

Application and modelling of hybrid stereolithography injection mould tooling

The use of stereolithography (SL) to make injection moulding tools has been shown previously to be an efficient way of producing rapid tools for simple geometries, aiming at small lot sizes with an acceptable degree of accuracy. This paper highlights the unexplored potential of using SL inserts in hybrid tools using practical experiments and FEA mould filling models. The practical experiments reveal problems incurred by uneven flow as a result of differential thermal conductivity between dissimilar mould materials in a hybrid tool. The FEA flow models confirm that this uneven flow would be anticipated when using finite element analysis (FEA) software. A further FEA stress analysis predicts that catastrophic mould failure will be expected under some conditions and these reflect the results found in the practical experiments. The use of a homogeneous SL tool eliminates the issues caused by uneven mould filling but results in thermal distortion of the female mould. Ultimately, a SL tool backfilled with low melt point alloy provides a solution that eliminates the problems of uneven filling and thermal distortion.