Pyrolysis conditions and ozone oxidation effects on ammonia adsorption in biomass generated chars

Ammonia adsorbents were generated via pyrolysis of biomass (peanut hulls and palm oil shells) over a range of temperatures and compared to a commercially available activated carbon (AC) and solid biomass residuals (wood and poultry litter fly ash). Dynamic ammonia adsorption studies (i.e., breakthrough curves) were performed using these adsorbents at 23 degrees C from 6 to 17 ppmv NH(3). Of the biomass chars, palm oil char generated at 500 degrees C had the highest NH(3) adsorption capacity (0.70 mg/g, 6 ppmv, 10% relative humidity (RH)), was similar to the AC, and contrasted to the other adsorbents (including the AC), the NH(3) adsorption capacity significantly increased if the relative humidity was increased (4 mg/g, 7 ppmv, 73% RH). Room temperature ozone treatment of the chars and activated carbon significantly increased the NH(3) adsorption capacity (10% RH); resultant adsorption capacity, q (mg/g) increased by approximately 2, 6, and 10 times for palm oil char, peanut hull char (pyrolysis only), and activated carbon, respectively. However, water vapor (73% RH at 23 degrees C) significantly reduced NH(3) adsorption capacity in the steam and ozone treated biomass, yet had no effect on the palm shell char generated at 500 degrees C. These results indicate the feasibility of using a low temperature (and thus low energy input) pyrolysis and activation process for the generation of NH(3) adsorbents from biomass residuals.     

Removal of Cr(VI) by thermally activated weed Salvinia cucullata in a fixed-bed column

The present study evaluates the feasibility of using a thermally activated fresh water weed in removing Cr(VI) from wastewater through column studies. The effect of flow rate, bed height and Cr(VI) concentration of the feed solution on the adsorption capacity of the activated weed was investigated. The adsorption capacity increased with decrease in both flow rate and bed height but increased with an increase in initial adsorbate concentration. Four different kinetic models, such as. Adams-Bohart, Bed Depth Service Time (BDST), Thomas and Yoon-Nelson models were first applied to the experimental data to predict the breakthrough curve and to determine the characteristic parameters of the column useful for designing large-scale column studies. Different statistical methods such as Sum of the Square of the Error (SSE), Sum of the Absolute Error (SAE), Average Relative Error (ARE), Average Relative Standard Error (ARS) and regression coefficient, were applied to evaluate the prominent and unique characteristic features of the experimental and predicted parameters under the respective models to find out the best fit. The performance stability of the adsorbent was tested by continuous adsorption-desorption studies.     

Effect of austempering treatment on microstructure and mechanical properties of high-Si steel

In the present investigation, the influence of austempering treatment on the microstructure and mechanical properties of silicon alloyed cast steel has been evaluated. The experimental results show that an ausferrite structure consisting of bainitic ferrite and retained austenite can be obtained by austempering the silicon alloyed cast steel at different austempering temperature. TEM observation and X-ray analysis confirmed the presence of retained austenite in the microstructure after austempering at 400 °C. The austempered steel has higher strength and ductility compared to as-cast steel. With increasing austempering temperature, the hardness and strength decreased but the percentage of elongation increased. A good combination of strength and ductility has been obtained at an austempering temperature of 400 °C.     

Growth, Optical, Mechanical, Dielectric and Theoretical Studies on Potassium Pentaborate Tetrahydrate (KB_5O_8·4H_2O) Single Crystal by Modified Sankaranarayanan-Ramasamy Method

A nonlinear optical single crystal of potassium pentaborate tetrahydrate (KB5O8·4H2O) has been grown from aqueous solution by using unidirectional crystal growth method of Sankaranarayanan-Ramasamy (SR) with a due modification in the growth assembly. Potassium pentaborate crystal of 60 mm length and 10 mm diameter has been grown along (100) plane with a growth rate of 3 mm per day within a period of 20 days. The grown crystal was subjected to single crystal X-ray diffraction analysis to confirm that the cry...     

Failure analysis of railroad wheels

Failure of three railroad wheels, each belonged to a different train but to the same heat, was analyzed. It was found that the wheels were failed due to improper heat treatment.     

Cenosphere filled aluminum syntactic foam made through stir-casting technique

Cenospheres in the range of 30–50 vol.% were used as space holders for making syntactic aluminum foam having density 1.5–1.9 gm/cc using stir-casting technique. The synthesized syntactic foam (SF) was characterized in terms of microstructures, hardness and compressive deformation behaviour. It was noted that the SF behaves like a high strength aluminium foam under compressive deformation exhibiting flat plateau region in the stress–strain curves. The plateau stress of SF decreases with cenosphere volume fraction vis-à-vis porosity following a power law relationship. But, the densification strain increases linearly with cenosphere volume fraction.     

Experimental determination of thermal conductivity of three nanofluids and development of new correlations

Experimental investigations have been carried out for determining the thermal conductivity of three nanofluids containing aluminum oxide, copper oxide and zinc oxide nanoparticles dispersed in a base fluid of 60:40 (by mass) ethylene glycol and water mixture. Particle volumetric concentration tested was up to 10% and the temperature range of the experiments was from 298 to 363 K. The results show an increase in the thermal conductivity of nanofluids compared to the base fluids with an increasing volumetric concentration of nanoparticles. The thermal conductivity also increases substantially with an increase in temperature. Several existing models for thermal conductivity were compared with the experimental data obtained from these nanofluids, and they do not exhibit good agreement. Therefore, a model was developed, which is a refinement of an existing model, which incorporates the classical Maxwell model and the Brownian motion effect to account for the thermal conductivity of nanofluids as a function of temperature, particle volumetric concentration, the properties of nanoparticles, and the base fluid, which agrees well with the experimental data.     

Isolation and evaluation of a high H2-producing lab isolate from cow dung

Hydrogen producing bacterial strain was isolated from Indian cow dung and identified of the bacterial family Enterobacteriaceae. This lab isolate was differentiated from Citrobacter Y-19 at molecular level by using RAPD, PCR based technique, and OPO-03₄₆₀ and OPO-17₈₀₀ RAPD marker for this specific strain (lab isolate) was identified. Fermentative studies were investigated for important parameters, starting with pH of the culture, temperature, inoculum age and inoculum volume, initial substrate concentration and different substrates. Among different substrates, dextrose and sucrose were the preferred substrates for hydrogen production. The optimal starting pH of the culture was found to be 5.0. The H₂ production increased with increase in temperature up to 30 °C. The maximum value of H₂ production was recorded when inoculum volume was 12.5% of the culture broth and inoculum age was 14 h. Under batch fermentation conditions, the maximum hydrogen production rate and yield were 355.2 ml l⁻¹ h⁻¹ and 2.1 mol/mol glucose (conversion 35%), respectively. These results indicate that this lab isolate is an ideal hydrogen producer.     

Biosorption of cadmium (II) and lead (II) from aqueous solutions using mushrooms: A comparative study

Sorption capacity of oyster mushroom (Pleurotus platypus), button mushroom (Agaricus bisporus) and milky mushroom (Calocybe indica) were evaluated on biosorption of heavy metals, viz. cadmium (II) and lead (II) from aqueous solutions. The optimum sorption conditions were studied for each metal separately. The desired pH of the aqueous solution was found to be 6.0 for the removal of cadmium (II) and 5.0 for removal of lead (II) for all the mushrooms. The percent removal of both the metals was found to increase with the increase in biosorbent dosage and contact time. The fitness of the biosorption data for Langmuir and Freundlich adsorption models was investigated. It was found that biosorption of cadmium (II) and lead (II) ions onto the biomass of the three mushrooms were better suitable to Langmuir than Freundlich adsorption model. P. platypus showed the highest metal uptake potential for cadmium (q_max 34.96 mg/g) whereas A. bisporus exhibited maximum potential for lead (q_max 33.78 mg/g). Milky mushroom showed the lowest metal uptake capacity for both the metals. The present data confirms that mushrooms may be used as efficient biosorbent for the removal of cadmium (II) and lead (II) ions from aqueous solution.     

The flexible PEI composites

The present study investigates the compatibilizing effect of polyphosphazene on the blends of poly(ether imide) (PEI) and thermotropic liquid crystalline polymer (Vectra‐B). FTIR study showed that there was a partial interaction or chemical reaction between the PEI and LCP in the presence of compatibilizer. Polyphosphazene is compatibilized with both PEI and LCP, which was evident from DMA results. From the X‐ray diffraction study, it has been observed that the crystalline structure of PEI–LCP blends was increased with the addition of compatibilizer. The thermal study of the composites has been studied by DTA/thermo gravimetric analyses (TGA). TGA thermograms showed an increase in decomposition temperature of PEI–LCP blends in the presence of compatibilizer. Measurement of the tensile properties showed an increase in the elongation as well as enhanced modulus and strength. From SEM micrographs of tensile fractured surfaces, the addition of compatibilizer to PEI–LCP blends was found to increase the adhesion between the matrix and the dispersed phase. POLYM. COMPOS., 27:533–538, 2006. © 2006 Society of Plastics Engineers