Study of inductively coupled Cl2/BCl3 plasma process for high etch rate selective etching of via-holes in GaAs

We have investigated the selective etching of 50 μm diameter via-holes for etch depth >200 μm using 30 μm thick photo resist mask in Inductively Coupled Plasma system with Cl₂/BCl₃ chemistry. Resultant etch rate/etch profiles are studied as a function of ICP process parameters and photo resist mask sidewall profile. Etch yield and aspect ratio variation with process pressure and substrate bias is also investigated at constant ICP power. The etch yield of ICP process increased with pressure due to reactant limited etch mechanism and reached a maximum of ∼19 for 200 μm depth at 50 mTorr pressure, 950 W coil power, 80 W substrate bias with an etch rate ∼4.9 μm/min. Final aspect ratio of etched holes is increased with pressure from 1.02 at 20 mTorr to 1.38 at 40 mTorr respectively for fixed etch time and then decreased to 1.24 at 50 mTorr pressure. The resultant final etch profile and undercut is found to have a strong dependence on the initial slope of photo resist mask sidewall angle and its selectivity in the pressure range of 20-50mTorr.     

A load frequency control algorithm based on a generalized approach

A generalized approach to load frequency control that combines discontinuous control and dual-mode control and uses variable-structure-systems concepts is developed. Using this approach, a novel load-frequency control algorithm is proposed. Studies on a multi-area power system, including generation rate constraint and governor dead-band, demonstrate the effectiveness of the control scheme     

Statistical evaluation of water tree lengths in XLPE cables at different temperatures

Accelerated aging of two types of commercially produced medium voltage XLPE insulated cables was carried out under the combined stresses of three types consisting of ionic aqueous species, elevated electrical stress and temperature cycling. After 1000 h of aging, the water tree parameters were evaluated. Results show that external ionic species exert profound impact on the generation of bow tie and vented water trees, while impurities inherently present in the cable components also contribute significantly. Temperature cycling increases the bow tie trees by an order of magnitude, while morphology of insulation influences the level of water tree degradation. The water tree population and their lengths were subjected to Weibull and log-normal models of statistical distributions and the data were found to fit better on the log-normal model. For a better statistical inference, a computer based Monte Carlo simulation was devised and used to precisely discriminate the two models. Simulation results further confirm that both types of water trees fit better on the log-normal model. The most likely mechanism for water tree degradation is fatigue based and hence mechanistic by nature.     

Determining SPICE parameter values for BJTs

The roles of hybrid-π, two-port, and SPICE transistor parameter are compared. A step-by-step procedure is described for determining numerical parameter values for a dynamic SPICE model of a bipolar junction from transistor manufacturer's measured data. The procedure is illustrated with an example     

Towards an integrated neonatal brain and cardiac examination capability at 7 T: electromagnetic field simulations and early phantom experiments using an 8-channel dipole array

Objective

Neonatal brain and cardiac imaging would benefit from the increased signal-to-noise ratio levels at 7 T compared to lower field. Optimal performance might be achieved using purpose designed RF coil arrays. In this study, we introduce an 8-channel dipole array and investigate, using simulations, its RF performances for neonatal applications at 7 T.

Methods

The 8-channel dipole array was designed and evaluated for neonatal brain/cardiac configurations in terms of SAR efficiency (ratio between transmit-field and maximum specific-absorption-rate level) using adjusted dielectric properties for neonate. A birdcage coil operating in circularly polarized mode was simulated for comparison. Validation of the simulation model was performed on phantom for the coil array.

Results

The 8-channel dipole array demonstrated up to 46% higher SAR efficiency levels compared to the birdcage coil in neonatal configurations, as the specific-absorption-rate levels were alleviated. An averaged normalized root-mean-square-error of 6.7% was found between measured and simulated transmit field maps on phantom.

Conclusion

The 8-channel dipole array design integrated for neonatal brain and cardiac MR was successfully demonstrated, in simulation with coverage of the baby and increased SAR efficiency levels compared to the birdcage. We conclude that the 8Tx-dipole array promises safe operating procedures for MR imaging of neonatal brain and heart at 7 T.

     

Electromechanical properties of ternary BiFeO<Subscript>3</Subscript>−0.35BaTiO<Subscript>3</Subscript>–BiGaO<Subscript>3</Subscript> piezoelectric ceramics

In the present work, composition dependent crystal structure, ferroelectric, piezoelectric, and temperature dependent dielectric properties of the BiGaO₃-modified (1–x)(0.65Bi_1.05FeO₃–0.35BaTiO₃) (BFBT35–xBG, where x?=?0.00–0.03) lead-free ceramics were systematically investigated by solid-state reaction method, followed by water quenching process. The substitution of BG successfully diffuses into the lattice of the BFBT ceramics, without changing the pseudo-cubic structure of the samples. The scanning electron microscopy (SEM) results revealed that the average grain size was increased with BG-content in BFBT system. The BFBT–xBG ceramics showed a maximum in permittivity (?_max) at temperatures (T_max) above 500 °C in the compositional range of 0.00?≤?x?≤?0.03. The electro-strain is measured to be 0.125% (d^*₃₃ ~ 250 pm/V) under unipolar fields (5 kV/mm) for BFBT–0.01BG ceramics. The same composition (x?=?0.01), large static piezoelectric constant (d₃₃ ~ 165 pC/N) and electromechanical coupling factor (k_p ~ 25%) were obtained. The above investigated characterizations suggests that BFBT–BG material is favorable for piezoelectric and high temperature applications.     

Evolution of ferroelectric and piezoelectric response by heat treatment in pseudocubic BiFeO<Subscript>3</Subscript>–BaTiO<Subscript>3</Subscript> ceramics

Heat treatment of ceramics is an important process to tailor the fine electromechanical properties. To explore the criteria for optimized heat treatment in a perovskite structure of (1–x)Bi_1.05FeO₃–xBaTiO₃ (BF–BT100x) system, the structural phase relation, ferroelectric and piezoelectric response of BF–BT36 and BF–BT40 ceramics prepared by furnace cooling (FC) and quenching process were investigated. The X-ray diffraction examination showed single pseudocubic perovskite structure for all the ceramics. The homogenous microstructure was obtained for all ceramics with relatively large grain size in the furnace cooled samples. Well saturated ferroelectric hysteresis loops and enhanced piezoelectric constant (d₃₃?=?97 pC/N) were achieved by quenching process. Dielectric curve of BF–BT36 showed large dielectric constant at its Curie temperature, however, BF–BT40 showed diffused relaxor-like dielectric anomalies. Quenched BF–BT36 samples showed typical butterfly like field induced strain curves, however negative strain decreased in BF–BT40 ceramics. From these investigated study, it is observed that BF–BT ceramics are very sensitive to the heat treatment process (furnace cooling and quenching) on the dielectric, electromechanical properties.     

A new hybrid approach for the solution of nonconvex economic dispatch problem with valve-point effects

Economic dispatch (ED) generally formulated as convex problem using optimization techniques by approximating generator input/output characteristic curves of monotonically increasing nature results in an inaccurate dispatch. The genetic algorithm has previously been used for the solution of problem for economic dispatch but takes longer time to converge to near optimal results. The hybrid approach is one of the methodologies used to fine tune the near optimal results produced by GA. This paper proposes new hybrid approach to solve the ED problem by using the valve-point effect. The approach we propose combines the genetic algorithm (GA) with active power optimization (APO) based on the Newton's second order approach (NSO). The genetic algorithm acts as a global optimizer giving near optimal generation schedule, which becomes the input for generation buses in APO algorithm. This algorithm acting as local search technique dispatching the generated active power of units for minimization of cost and gives optimum generation schedule. Three machines 6-bus, IEEE 5-machines 14-bus, and IEEE 6-mchines 30-bus systems have been tested for validation of our approach. Results of the proposed scheme compared with results obtained from GA alone give significant improvements in the generation cost showing the promise of the proposed approach.     

Interaction of cetyltrimethylammonium bromide with drug in aqueous/ electrolyte solution: A combined conductometric and molecular dynamics method study

Interaction between beta-lactum antibiotic drug ciprofloxacin hydrochloride(CFH)and cationic surfactant cetyltrimethylammonium bromide(CTAB)was performed conductometrically in aqueous as well as in the occurrence of different salts(NaCl,KCl as well as NH_4Cl)over the temperature range of 298.15–323.15 K at the regular interval of 5 K.CFH drug has been suggested for the treatment of bacterial infections such as urinary tract infections and acute sinusitis.A clear critical micelle concentration(CMC)was obtained for pure CTAB as well as(CFH+CTAB)mixed systems.The decrease in CMC values of CTAB caused by the addition of CFH reveals the existence of the interaction between the components and therefore it is the indication of micelle formation at lower concentration of CTAB and their CMC values further decrease in attendance of salts.A nonlinear behavior in the CMC versus T plot was observed in all the cases.The ΔG_m~0 values are found to be negative in present study systems demonstrated the stability of the solution.The values of ΔH_m~0 and ΔS_m~0 reveal the existence of hydrophobic and electrostatic interactions between CFH and CTAB.The thermodynamic properties of transfer for the micellization were also evaluated and discussed in detail.Molecular dynamic simulation disclosed that environment of water and salts have impact on the hydrophobic interaction between CFH and CTAB.In water and salts,CTAB adopts spherical micelle in which charged hydrophilic groups are interacted with waters whereas hydrophobic tails form the core of the micelle.This hydrophobic core region is highly conserved and protected.In addition,micelle formation is more favorable in aqueous Na Cl solution than other solutions.     

Cu-K/Al2O3 based catalysts for conversion of carbon dioxide to methane and carbon monoxide

Abstract

A series of Cu-K/Al₂O₃ catalysts were synthesized by wet impregnation technique. The reduced catalysts were further used for conversion of carbon dioxide to methane and carbon monoxide. Moreover, the fresh and used catalysts were characterized to investigate the changes in the surface morphology, metal dispersion, surface area, crystalline phases, and functional groups of studied catalysts. The SEM analysis of fresh and spent catalysts showed no remarkable difference in surface morphology with irregular shaped agglomerated particles. Furthermore, TEM micrographs presented the well distribution of metal catalyst over alumina support. The decrease in surface area from 115 to 77?m²/g for Cu_1.62-K_0.5/Al₂O₃ after reaction was related to sintering and oxidation of catalyst during reaction. XRD revealed the disappearance of some minor peaks which can be associated with the sintering of spent catalyst. FTIR also presented some new peak for spent catalyst which can be linked with metal oxides. Moreover, various reaction conditions of temperature (230, 400, and 600?°C), pressure (1 and 7?bar), and feed molar ratio of H₂/CO₂ (2:1 and 4:1) were investigated using different Cu loading (0, 1, 1.25, 1.62, and 4 weight percent). A maximum CO₂ conversion of 63% with 39% CH₄ selectivity was achieved by using Cu_1.62-K_0.5/Al₂O₃ at 600?°C, molar ratio of H₂/CO₂ 4 under 7?bar. The presence of K on the surface of synthesized catalyst increased the CO₂ conversion from 48% (Cu₁/Al₂O₃) to 55% (Cu₁-K_0.5/Al₂O₃) at above mentioned reaction conditions which suggested the promoter effect of K during conversion of carbon dioxide.