Al、Mo含量对铸造钛合金力学性能的影响

运用正交实验 ,考察了Al、Mo含量对Ti Al Mo 1Zr系铸造钛合金力学性能的影响。试验结果表明 :随Al、Mo含量提高 ,铸造合金的强度增加 ,塑性和冲击韧性降低 ,但Al、Mo的交互作用却使合金塑性提高 ,强度和冲击韧性降低     

珠光体球化的分形研究

珠光体球化反映到金相上，是一种不规则图像的变化，并且具有分形的特征，可望用分形几何的方法来进行描述。以Cr-Mo钢的珠光体球化为例，用分形维数来描述珠光体球化程度；用小岛法对15CrMo钢的珠光体球化图谱进行了测量。实验表明，珠光体球化从1级到6级，其相应的分形维数范围为1.3156-1.9282。从电厂运行了10^5h的15CrMo钢管上取样，实测了该试样的珠光体球化等级，结果表明，以分形维数表示的球化程度与按图谱评定的球化等级完全吻合。     

海底输油管道内智能引导装置研究

对海底输油管道内智能引导装置研究的必要性进行了分析;介绍了国内外在该领域的技术发展状况。针对智能引导装置的作业对象和环境,提出了技术要求和指标,对智能引导装置进行了总体设计,分析了其作业机理,建立了力学模型并进行了计算。对智能引导装置的控制系统进行了设计,提出了设计过程中应注意的问题。所研制的管内轮式智能引导装置具有质量轻、输出牵引力大、体积小、结构紧凑等特点,对较小管内空间类似系统的设计有一定参考价值。     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

MIM隧道发光结的负阻现象

本文介绍了薄膜隧道发光结的基本结构、发光机理，阐述了其Ｉ－Ｖ特性中的负阻现象。简单介绍了ＭＩＭ结构负阻的几种解释，根据热像仪照片和低温测试结果分析，再结合Ｄｅａｒｍａｌｅｙ导电模型，我们提出了ＭＩＭ负阻的物理模型，理论与实验符合较好，最后分析了负阻现象的应用前景。     

Abnormal junction profile of silicided p+/n shallowjunctions: a leakage mechanism

The leakage mechanism in p⁺/n shallow junctions fabricated using Co silicidation and shallow trench isolation processes has been investigated using transmission electron microscopy (TEM) combined with selective chemical etching. TEM and TSUPREM-4 simulation results show that dopant profiles bend upward near the edge of the active region. The formation of the abnormal profile is attributed to transient enhanced diffusion induced by source/drain implantation. Based on the TEM and simulation results, it is suggested that the shallower junctions formed near the active edge can serve as a source for leakage current in the silicided p+ /n shallow junctions     

The pharmacokinetics of pancuronium bromide in infants, children and adults

Laparoscopic retroperitoneal lymph node dissection is a new surgical procedure used to enhance staging in men with clinical stage I nonseminomatous germ cell tumors of the testis. The procedure has been performed in a limited number of patients at several centers with extensive laparoscopic experience. Laparoscopic retroperitoneal lymphadenectomy is a technically demanding procedure which can be successfully completed in the majority of patients. However, the risk of complications is greater than in patients who undergo standard open retroperitoneal lymph node dissection. The primary advantage of a laparoscopic approach is shortened hospitalization and rapid return to normal activity. The role of laparoscopy in the management of patients with testis malignancy has not been defined. The use of this staging procedure may help minimize the need for surveillance studies following surgery and may be best utilized in men with a lower likelihood of nodal metastases. Ultimately, prospective study in large groups of patients will be necessary to determine the role of laparoscopic retroperitoneal lymph node dissection in patients with testis cancer.     

C-t analysis of MOS capacitors under constant current stress

The effect of high oxide field stress is studied using capacitance-time (C-t) measurements of MOS capacitors. The stress results in parallel shifts of the C-t curve along the time axis. The flatband voltage shift ΔV_FB obtained from the initial deep depletion capacitance C(t=0⁺) follows the same trend as that from the high-frequency C-V characteristics. However, the discrepancy between the two flatband voltages becomes larger as the stress increases due to the effect of interface charges on C-t characteristics. The flatband voltage difference is converted to interface trap density, showing a steady increase of interface trap density with stress, similar to that from low-frequency C-V measurements     

冶金过程中复杂夹杂物和钢液化学平衡计算

本文提出一个同温冶炼过程中预测非金属夹杂物沉淀的计算机程序。本研究中，多元硅酸盐溶体的Ｇｉｂｂｓ自由能由基于统计热力学的晶胞模型来计算，该晶胞模型按照氧与周围的阳离子构成的对称和非对称晶胞来描述硅酸盐熔体结构，假定高温冶炼时认与非金属夹杂物平衡，钢液中氧化物元素的活度由Ｗａｇｎｅｒ交互作用系数来计算，利用本程序可以估计炼钢时沉淀的非金属氧化物的成分，为调整冶炼工艺和提高产品质量提供指导，进一步可计     

以网格曲线为连续条件的光滑曲面

本文提出一种以网格边界曲线定义曲面的方法。曲面的计算式唯一地由网格的四条边界线的参数而定，各网格间连接的光滑度完全由网格间的边界线的光滑度来决定。当网格间的边界线具有Ｃ~１连续以上的光滑度时，网络曲面间将自动保证是Ｃ~１连续的，否则将是Ｃ~０连续。利用这个方法，可以方便地从线框模型（ｗｉｒｅ－ｆｒａｍｅｍｏｄｅｌ）建立面模型（ｓｕｒｆａｃｅｍｏｄｅｌ）。